Search Documents

By Peter W. Harben

Once considered the dowdy country cousins of the glamorous metallics, industrial minerals are shedding their old image. They are neither common nor easy and their time has come in an age of increasing specialization. Consider that of the 45 or so industrial minerals and rocks listed in [Table 1], almost three-quarters have ten or fewer significant suppliers (i.e., those individual countries contributing 2% or more of total world production); in more than half the cases, 85% of world production is accounted for by only five countries or fewer. Curiously, even materials that appear to be virtually ubiquitous like crushed rock and common salt have significant production vacuums. For example, there is a severe lack of sound aggregates along the US Gulf Coast and common salt production on a large scale is virtually absent in central Africa. These examples all underline the obvious, but acute truism that "The single most important fact about mineral resources is that they are not distributed equally over the world" (Flawn, 1966). Just as significant today is that human resources are not distributed equally over the world, and so arise some interesting commercial incongruities. In certain regions raw materials are plentiful but consumers are not, and without a market a mineral deposit is merely a geological curiosity. Elsewhere, there may be a market but no local raw material supply. For example, despite a huge market there is no or virtually no commercial production of chromite, diamonds, and manganese in the United States and Canada, nor phosphate rock, diamonds, rutile, and zirconium minerals in western Europe. In contrast, Australia with its small domestic market is the world's largest supplier of bauxite, diamonds, ilmenite, natural and synthetic rutile, and zircon; the same is true for South Africa which is a leading producer of chromite, manganese, diamonds, andalusite, ilmenite, rutile, and zircon (Table 2). In the commercial world, Nature's uneven distribution is counterbalanced by deep sea international trade.

Jan 1, 1994

By Anna Sieminska-Lewandowska, Monika Mitew-Czajewska

"The construction of 6.3 km long central part of 2nd metro line in Warsaw was completed in September 2014 (7 stations - out of which three 25m deep stations - built using cut and cover method; two single-track tunnels constructed using four EPB TBMs as well as a short NATM section with soil freezing below the existing road tunnel). Central section of the 2nd metro line was opened to public after verification and testing in March 2015. Design and build tender for the extension of this line in East (three stations) and West direction (three stations) was announced with total length of running tunnels – approx. 5 km. Detailed description of a very complex geotechnical context, different construction methods, challenges encountered and solved during construction and finally lessons learnt on this interesting project are presented in the paper. DESCRITPTION OF THE PROJECT Introduction The very first concept plan of the metro system in Warsaw was designed several years after regaining independence by Poland in 1918. In 1929, following the geotechnical survey, design works begun, but the economic crisis of the 1930s stopped it. After a few years of break, in 1938 a coherent concept of the metro network was proposed to be implemented in phases over the next 35 years. In total, construction of 46 kilometers of metro, including 31 km of tunnels and 15 km on surface, was planned. Unfortunately, World War 2 made the implementation of those plans impossible. In the post-war period several metro designs were elaborated, but none except one was scheduled for implementation. Construction of the 1st, 23.1 km long, North-South line commenced in 1983 and finished in 2008 (Sieminska-Lewandowska et all. 2009). Nowadays, Warsaw covers the area of 517 km2 and, according to year 2014 statistical data, the city has much more than 1.7 million inhabitants. Only one operating metro line is not sufficient for such a populated city. Up-to-date metro plan, shown on Figure 1, includes also 30.5 km long 2nd metro line. It’s route is divided into four sections: Western Section with the length of approx. 9.2 km and 9 stations, Central Section with the length of 6.3 km and 7 stations, North-East Section with the length of 7.7 km and 6 stations, South-East Section with the length of 7.1 km and 6 stations. The construction of the central part of the 2nd metro line in Warsaw was completed in September 2014 and its operation started in March 2015. The paper focuses on challenges encountered and solved and lessons learnt during construction of the central part of the 2nd metro line in Warsaw."

Jan 1, 2016

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By F. B. Henderson, D. Bird, P. L. Hauff, E. C. Prosh

A National Aeronautics and Space Administration (NASA)-funded project (NASA Grant #NAG13-02026) is underway to determine the ability of hyperspectral remote sensing to map mineralogy that affects water quality within a watershed and to identify the relative contributions of natural and anthropogenic sources to that drainage. Natural sources, particularly areas of pyritic hydrothermal alteration, have been found by the Colorado Geological Survey to be a significant source, sometimes the only source, for acidity and/or metals in a number of areas of Colorado (Neubert, 2000). This situation undoubtedly occurs in many places in the Western United States and elsewhere where metallic mineralization occurs. Anthropogenic sources arise from mining and other human activities that increase the exposure of acid-generating materials to weathering processes, thereby increasing acidity and metal loading to drainages where that activity is occurring or has occurred. This project is attempting to determine if these sources can be differentiated through mineralogical analysis, in conjunction with surface water chemistry that controls the precipitated minerals, of the impacted drainages by remote sensing techniques.

Jan 1, 2003

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state's highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002

By T. C. Rao, N. Suresh, M. Vanangamudi

Experiments have been conducted on a 76¬mm water-only cyclone treating cowl below 2 mm size having different proportion of -0.075 mm fines. The effect of cone angle of the cyclone (compound cone) has been analyzed on water split, separation of -0.075 mm fines, separation of coarse solids, and on separation behavior of individual size ructions of the feed. It has been noted from the results that there exists a linear relationship between the flow rate of water in the feed and flow rate of water reporting to overflow stream. This relationship is independent of the cone angle and, with changes in the fines content in the feed, only the intercept of the straight varies, keeping the slope constant. Further, it has also been found that the percentage of fines below 0.075 mm reporting to the overflow is directly proportional to the percentage of feed wafer reporting to the overflow. This relationship is found to be independent of the cone angle and the fines in the feed. The performance of the water-only cyclone has been analyzed by plotting partition curves for different experimental conditions. In addition to this, the Rosin-Rammler equation has been fitted to the partition curves of the hulk feed and individual size-fractions. Tile analysis of the results has revealed that the specific gravity of separation increases with increase in the cone angle of the cyclone while it decreases with increase in percent fines present in the feed. Mathematical relationships have been developed to relate the variation in SG50 with cone angle and percent fines in the feed.

Jan 1, 1990

By T. J. Lien

AMAX Coal Company's Belle Ayr coal dryer is the first industry attempt to commercialize sub-bituminous coal drying which has been the subject of laboratory and pilot plant tests for almost two decades. This paper presents the historical background, construction, start-up and operation of this adaption of fluidized bed coal drying technology to Powder River Basin coal. The flowsheet and operational problems encountered during plant start-up are discussed together with general material balance and product quality.

Jan 1, 1990

By Yoshinori Shimada, Oleg Kotiaev, Hiroaki Sakamoto, Toshihiro Asakura, Naotoshi Yasuda, Norikazu Misaki, Masahiro Shinoda

"To ensure that trains run safely, the performance of railway civil engineering structures is checked by periodic inspections. General inspection method has merits and demerits, but none of them offers the combination of high accuracy and quick inspection. In an effort to resolve this problem, West Japan Railway Company, the Institute for Laser Technology and the Railway Technical Research Institute jointly developed a remote laser sensing system as an alternative to the impact acoustics method for detecting defective concrete elements in tunnel linings. The proposed remote laser sensing system has two lasers, one to apply an impact to the concrete surface and the other to measure the vibration of the concrete generated by the impact laser. The impact laser is a high-energy pulse laser that induces vibration in the concrete. The detection laser has a signal beam and a reference beam. The signal beam reflects on the concrete surface and goes into the dynamic hologram crystal. The reference beam diffracts in the dynamic hologram and enters the detection sensor with the signal beam. The vibration of the concrete surface can be measured to detect the movement of an interference pattern. A prototype of the remote laser sensing system was developed as shown in Figure1. A vibration and acoustic insulators are equipped to remove a noise generated from a maintenance car or electric generator in this system. The proposed laser remote sensing system and the detection algorithm were verified with the help of field test conducted in a tunnel on the Shinkansen. An impact test using hammering was applied to obtain the accurate response acceleration on the surface of the concrete before application of the proposed method. In this test, the result obtained from the proposed method has good agreement with that obtained from the impact test by hammering. Consequently, it is verified that the proposed method can be used as an alternative to the standard impact acoustics method."

Jan 1, 2016

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By Welland L. Ott, Hans J. Rumland

The Falconbridge Dominicana laboratory receives samples from all parts of the operation. Ore, metal and oil samples are taken by operating departments, gas and water samples by the laboratory staff. Physical sample preparation is essentially standard and produces comminuted samples for wet-chemical analysis and X-ray fluorescence analysis (XRF). T he main operating sections of the laboratory are described indicating in each case the type of instrumentation and method used, sample types analysed and comments on problems experienced. Emphasis is given to the sample preparation and X-ray sections especially with regard to the difficulties caused by our heterogenous ore material, calibration of the instrument and operational malfunctions. General problems related to our remote location and the tropical climate are discussed. Limited statistics on instrument availability, and stability, accuracy, precision, etc., are given.

Jan 1, 1979

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004

By Michael E. Salovich

The U. S. Department of Interior, Bureau of Mines (Bureau) has developed a prototype version of a computer application that combines hydrologic analysis with object-oriented graphics. This software is unique in that it presents analytic element analysis within an object-oriented CAD environment. Its user interface employs mouse handling, scrolling windows, dialog boxes, palettes, and pulldown menus. It can import scanned images of maps and overlay these images within the same window. This application was developed using object-oriented programming techniques. Several programming issues concerning graphics had to be resolved during development of this system. These include (1) how to represent hydrologic elements as graphical objects, (2) how to translate screen coordinates to map coordinates, (3) how to implement ?zooming? (changing the magnification level of a window), (4) how to overlay layers of images, and (5) how to import scanned images of maps. An object library was used to implement graphical user interface features such as scrolling windows and pull-down menus. Algorithms for CAD features such as map coordinate translation, zooming, and the layering of images were developed by Bureau researchers. The application has a modular source code structure and can be modified for use in other research applications.

Jan 1, 1992

By Edward S. Plotkin

The tunneling construction industry faces a new challenge in endeavoring to comply with the multitude of regulations and standards of the Occupational Safety and Health Administration and to work following accepted and experienced tunneling practices. Tunnel inspections appear to be gaining in priority. The national OSHA inspection activities reported for the year 1976 in the construction industry are as follows: 989 Inspections 45 As result of Accidents 186 As result of Complaints 605 General 153 Follow Up 34% Were found to be in compliance 714 Citations were Issued 1,825 Violations were found (201 of which were serious; 1573 were non-serious; 51 were imminent danger. There were no recorded failures to abate a violation in our industry.) The five general priorities by which a company would be scheduled for an inspection in descending order are: imminent danger situations, reports of fatal accidents or catastrophies, inspections in response to valid employee C( taints, inspections of work places covered by National Emphasis Program NEP, (OSHA's NEP has been designed to impact on any industry having a very high injury or illness rate) and finally random inspections of work places covered by OSHA. The following criteria in selecting companies for random inspections is used by OSHA.

Jan 1, 1979

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By E. V. Kuzmin

The rock properties improvement means the exchange of natural properties: increase of stability, strain and compress tension, reduction of gas-liquid filtering property, increase Jung- module, other mechanical and physical parameters of rocks by injection the hardening materials, such as polymeric pitches, micro-or geocements by special technology under high pressure, to fill cracks. Flow of liquid materials between the rock units and hardening under high pressure create full redistribution of rock pressure in rock massif. There are many reasons to use this technology in underground mining, tunnelling, creation barrier technology in raioactive, chemical and other danger material site etc.

Jan 1, 1996