Search Documents

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By Stuart F. McTavish

Mechanically suitable grinding mills became available to the mining industry in 1908. Since then, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. Most important, they had to last long enough in an operating mill to protect its structure from the abrasive wear of the ore and the grinding media. In addition, they had to be capable of efficiently transferring the energy from the mill to the mill charge in order to facilitate the grinding process. And these liners had to be easy to install and remove. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high-carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. In the early 1920s, pieces of solid rubber truck tires were used as emergency repairs for broken cast metal liners. Thus was rubber first introduced as a mill liner material. The first patent for rubber mill liners was awarded in 1921 to James Denny and Rolla Watson, both of the Coniagas Mine in Cobalt, Ontario, and to Dale Barnum of the Comstock Lode in Virginia City, NV. This original design was covered under US Patent No. 1470597. It had a fabric backed rubber that was bonded to the shell of the mill.

Jan 1, 1990

By M. E. Poad, W. G. Pariseau, M. A. Laurenti

In 1986, a cooperative effort by Homestake Mining Co., the US Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high-grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will he safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modeling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1996

By Patricia T. Foley

An analysis of the demand for copper shows a widely varying pattern of end use. For example, copper tube is the most popular material for hot water supply in the US and northern Europe, but galvanized steel is used in Japan and plastics are used in developing countries. In addition to such peculiarities of end use, the demand for copper varies among countries depending on the stage of industrialization and the extent that the copper processing industries are developed. Brazil, with its abundant supplies of bauxite and hydroelectric power, uses aluminun in place of copper wherever possible. South Korea, with its export oriented economy and its advanced custom smelting and fabricating industries, favors copper. Understanding the details of demand in different countries enhances statistical derived forecasts and illustrates potential new markets.

Jan 1, 1986

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By M. Charles Gilbert

Basement rocks in southern Oklahoma are divided into two groups. One group is the Lower Cambrian Wichita Igneous Province, a diverse igneous suite that crops out in the western Arbuckle Mountains and in the Wichita Mountains. These largely bimodal igneous rocks were emplaced in an intracratonic-rift environment. The other group, the older, is a set of Precambrian rocks of the Eastern Arbuckle Province, yielding ages between 1,350 and 1,400 Ma, exposed in the core of the eastern Arbuckle Mountains. These are deeply eroded mesozonal granitic rocks and associated granitic gneisses cut by numerous dikes ranging in composition from diabase to rhyolite. The southern Oklahoma igneous rocks have long been utilized mostly as dimension and crushed stone. Most of the early quarries were in granite of various red hues for monuments and facing stones. Large crushed-stone quarries are now exploiting both granite and rhyolite, which is used chiefly as aggregate and railroad ballast. The exposed basement rocks in Oklahoma represent an underdeveloped and accessible resource.

Jan 1, 1999

By R. Gong, R. Bhaskar

The development of a three-dimensional mathematical model for evaluating airflow fields at a continuous miner face is described. The model utilizes three-dimensional incompressible flow, mass continuity, and momentum (Navier-Stokes) equations to predict the airflow velocity at the face. Obstacles and equipment in the face area are modeled using appropriate boundary conditions. Parameters such as flow velocity and face dimensions can be modified and evaluated for various schemes, such as exhausting and blowing ventilation, using either brattice or tubing. A model such as the one described, with additions for local effects, can be used to evaluate novel face ventilation ideas before initiating expensive full-scale tests or field studies. The model described is a step in the direction of advanced predictor models.

Jan 1, 1993

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

By A. M. Taweel, M. T. Ityokumbul, A. I. A. Salama, M. W. Mikhail

The liquid-phase mixing within CANMET's Western Research Centre's (WRC) 0.76-m-diem pilot-plant flotation column was characterized using a salt tracer. The process variables studied were frother addition and, gas and liquid flow rates. The response of the column to a tracer pulse was monitored at three axial and two radial locations. The results showed that the 2-tph flotation column was well mixed. Discussed are the implications of this observation to column design and scale-up.

Jan 1, 1996

By D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity which exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into worldwide business with a capacity of about one-half million tons/yr. This paper will present data on the chemistry, mining, manufacturing and applications for acid- activated clays.

Jan 1, 1986

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By J. Herbst, A. J. Lynch, E. V. Manlapig, G. C. Throne, J. S. Hall, G. Poling

Modelling of industrial sulphide flotation based on data collected in several flotation plants is discussed. A mechanistic approach is used in which it is recognised that flotation is a two stage process with concentration occurring both in the pulp and in the froth. The important features of the model, which is a kinetic model, are – 1. for each particle species there is a range of flotation rates which corresponds to the range of particle sizes, 2. the flotation rates of the liberated gangue particles which have no hydrophobic properties are dependent on the flotation rate of water and are controlled by variables such as the air and frother addition rates, and the pulp level, 3. as an approximation the valuable sulphide particles may be regarded as being present in two groups with high and low flotation rate constants, 4. increase in the addition rate of collector tends to increase the proportion of sulphide particles which are in the high flotation rate constant group. The actual flotation rate of each group of particles is a combination of an "inherent" flotation rate and a flotation rate which is dependent on the flotation rate of water, at particular air and frother addition rates and pulp levels there is a physical limit to the rate at which particles can be transported into the concentrate and this is recognised in the

Jan 1, 1976

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By Ted D. Maki, Joseph B. Taylor

INTRODUCTION FMC's Paradise Peak mine, located 13 Ian (8 miles) south of Gabbs, Nevada, became opera¬tional in April of 1986 (Figure 1). It was designed and built by Davy McKee, who was instrumental in equipment design and selection. It is the 7th largest gold deposit in the United States with defined reserves of 10.9 mt (12 million st) containing 34 million gms (1.1 million tr oz) of recoverable gold and 933 million gms (30 million tr oz) of recoverable silver. The mine extracts ore by the open-pit method, taking advantage of a 1.5:1 stripping ratio. The mill operates at a 3600 mt/day (4000 st/d) capacity. Crushing is done in three stages to achieve an ore size of minus 0.635 cm (0.25 inches). Grinding further reduces the ore to 85% minus 100 mesh. The ground ore is treated with cyanide in agitated leach tanks and then washed in the counter-current decantation (OCD) thickeners. Zinc is added to the clarified, deaerated pregnant solution to precipitate the precious metals. The precipitate is acid digested to eliminate excess zinc, filtered and retorted to drive off contained mercury. The retorted precipitate is then fluxed, melted and poured through cascade molds. Dore bars are cleaned for shipment and the slag is sent to an in-house slag treatment system. ELECTROSTATIC SEPARATION The dry electrostatic slag treatment system at Paradise Peak is the first installation of its kind. Electrostatic separation has been widely used in mineral processing since the early 1950's. A brief discussion of the theory behind the process is helpful to those not familiar to electrostatic separation. Charging and sepa¬rating slags, dry minerals or other materials by ion bombardment is the most common form of electrostatic separation. Millions of tonnes of minerals are processed each year by this method. In an ion bombardment separation, granular material is fed onto a grounded metal cylinder (or roll) and charged by a corona-producing electrode placed above the roll's surface (Figure 2). While both conductors and non¬conductors become charged, only the conductor is able to lose its charge. The charged non¬conductor, as it rests on the roll's surface, "sees" an oppositely charged image of itself in the metal surface. It is attracted to the image charge, becomes electrostatically pinned to, and moves with the roll's surface. The conductive particle also sees an image and is attracted to it. But upon touching the roll's surface, it discharges rapidly to the grounded surface and is thrown free from the roll's surface with a projectile motion. In the case of precious metal slags, the con¬ductive particles would be metallic prills of dore metal; and the nonconductive particles would be the slag, free of metal. Middling grains, generally, are in the form of a metallic prill encased in or incompletely liberated from slag. LABORATORY TESTING A number of precious metal slag samples have been tested in the laboratory. It has been found that the composition of slags vary widely from one refinery operation to another. Typical laboratory procedure is to crush and size the slag followed by two-stage lab-scale electro¬static separation. The conductor fractions from the first and second pass are then combined as a prill concentrate; middlings fraction and clean slag tailings from the second pass are held separate. Selected results from laboratory testing are shown in Table 1. It is important to note in Table 1 that the assays represent overall silver and gold, not metallic values. From experience, the laboratory results are typically lower in grade and recovery than the industrial installations. This is largely due to the hydroscopic nature of precious metal slags coupled with the high local humidity in Carpco's Jacksonville, Florida, location. Relative humidity in Jacksonville can range form 60-95%, while most mining locations in the

Jan 1, 1987

By F. Michael Jenkins, Elaine T. Bowers

Longwall systems are used to mine approximately 50 pct of the world's total coal production. Single entries are the predominate method of longwall development in Europe and Asia where mining conditions are much more severe than those encountered in the United States. During the 1970's and early 19801s, the Bureau of Mines and the coal mining industry invested nearly $20 million in single entry and related research. This report reviews the accomplishments of single-entry research in the United States. Two U.S. single-entry field projects are described; the Sunnyside Single-Entry Project conducted in central Utah, and the Tunnel Boring project conducted in northern West Virginia. Two other important studies are discussed, the Single-Entry Study by NAMCO and the Single-Entry Design Study by Ketron. Inc. This review compares the resulting technology with European counterparts to further assess the utility and efficiency of the U.S. systems, and final1 y, it discusses future research and development options which would lead to safe and productive single-entry longwall development in this country.

Jan 1, 1986

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976