Search Documents

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By M. J. Hrebar

This paper reviews large dozer stripping techniques and presents results of two field studies. The first is a seven-shift study of a contour block stripping operation where a Caterpillar DII is used as the primary stripping equipment. The second is a two-shift study of two Cat DIIs dozing blast cast material ahead of a dragline operation. Surveys and continuous time studies were used to determine production rates and as a basis for forecasting unit stripping costs in both cases.

Jan 1, 1994

By Leonard A. Eros

In many mining applications it is not practical to use gravity takeups. In these situations hydraulic takeups are often utilized. Performance specifications are often compromised by designs which have inherently high internal friction and inefficient hydraulic designs. This results in performance which does not match the requirements of the conveyor system. A computer model has been built to check unit efficiencies and field measurements have been taken which verify the results.

Jan 1, 1993

By M. A. Marticorena, R. Stratton-Crawley, C. I. Basilio

Diethylenetriamine (DETA) is a selective depressant for nickeliferous pyrrhotite during pentlandite flotation. Laboratory flotation tests conducted on ore and process samples showed that pyrrhotite rejection is greatly improved by small additions of DETA; however, the effectiveness of this depressant is most noticeable when the mineral sample is oxidized. LIMS and XPS analyses conducted on flotation products and pyrrhotite specimens showed that the difficulty in pyrrhotite rejection arises from inadvertent activation of the mineral by heavy metal ions, such as Ni2+, cu2+ and Ag+, that are present in the process water. In the presence of DETA, however, the mineral is deactivated under oxidizing conditions. The deactivation mechanism may involve oxidation of the activation products, which are likely in the form of heavy metal sulfides, followed by solubilization by DETA. FTIR spectra of pyrrhotite electrodes contacted with DETA showed no trace of the reagent on the surface, substantiating the view that its role is one of complexing agent that enhances the dissolution of activation products under oxidizing conditions. FTIR spectra of pyrrhotite contacted with amyl xanthate solutions showed that both dixanthogen and iron xanthate are formed on the surface, the latter becoming more predominant at higher potentials. In the presence of DETA, however, only a small amount of xanthate is adsorbed on the mineral at potentials (Eh) approximately 200 mV higher than the case without DETA.

Jan 1, 1995

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By Harrison R. Cooper

INTRODUCTION AND SUMMARY Phosphate matrix beneficiation is the process of providing a mineral product suitable for downstream chemical processing to yield high analysis chemical fertil- zers. Extraneous contaminants, clays and gangue solids, are separated by screening and flotation. Reject materials always carry with them some phosphate mineral values, however. A continuing objective is minimizing phosphate losses discarded with tailings as a principle factor in maintaining beneficiation efficiency. The quest for efficiency, and improved productivity, during beneficiation is hampered by disturbances arising from among the following: o Natural variance of phosphate deposit compositions, o Minimal control over managing ore matrix supply to the plants, o Screening and flotation mechanical upsets and inefficiencies. Production personnel, in recognizing these factors, attempt corrections for changed process conditions. This response usually has limited effect. Efforts of product- ion personnel to correct for upsets of the process may often diminish efficiencies rather than improve them. Lack of prompt data for analysis of process streams is an important contributing cause of inefficient operation. Discussion in this paper examines methods for improved process control in Florida phosphate beneficiation with particular emphasis on use of on-stream analysis to aid gaining productivity. The Florida Institute of Phosphate Research has supported demonstration of on-stream analysis applicable to improved process control. Concurrently, work is proceeding world-wide in the phosphate industry toward practical on-line analysis technology. Table 1 summarizes viable methods for real-time analysis data as result of work by individual companies and research organizations. A recently completed investigation (sponsored by the Florida Institute of Phosphate Research) of beneficiation efficiency was carried out in two Florida beneficiation plants using a newly developed on-stream analyzer for phosphorus (1). BPL measurements were taken at frequent intervals over two to three weeks of routine operation. Grades are expressed in "BPL", with one BPL, or bone phosphate of lime unit, equal to 0.46 P^Y2^YO^Y5^Y. The time series of feed and tailing BPL data were evaluated by statistical procedures. Results show avoidable losses can be five per cent or greater of mineral values in feed. Use of modern process control methods in Florida phosphate mining began several years ago (2, 3). Benefits of stabilizing control used in one of the two plants where data were collected for the investigation, in comparison to manual control in the other, are outlined. Process control technology developments reported from European and South African phosphate mining operations are also noted (4, 5). It is now well accepted that advanced control techniques can increase beneficiation productivity by better management of losses. However, to make advanced control effective, real-time measurements are needed of feed and tailings BPL as well as mass flow rates.

Jan 1, 1993

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By Carl E. Brechtel, Edward D. Thimons

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kw (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1987

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By C. R. Landis

The Wyoming bentonite industry continued its run of stable, if not strong, growth in its complex markets. Growth at the macroscale was fueled by a strong domestic economy, the weakening of the U.S. dollar in the global market and strong worldwide global demand. Challenges to the benchmark of the industry were rapid and saw ongoing increases in raw material costs(pallets, bags and additives), higher energy costs and higher overall transportation costs for all modes of movement. Exports continued to be assisted by dollar depreciation (5 percent to 10 percent) from January 2004to January 2005. This depreciation followed the significant weakening of 2003. And it was most favorable during the pullback in fuel and shipping rates in the second half of the year.

Jan 1, 2005

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By Joe W. Siefke

The world-class Kramer sodium borate deposit is being developed by modern open pit operations near Boron, California. The deposit is a bedded, lenticular sedimentary sequence of borax and kernite crystals together with claystone. The borates dip south into a structural basin-bounding fault and were formed in the bottom muds of a permanent shallow lake. The lake was fed boron and sodium-rich solutions from a thermal spring source of volcanic origin. In addition to deposit geology, present day geotechnical concerns such as groundwater and slope stability will be discussed.

Jan 1, 1995

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By J. D. Vincent

The Mission By-Products Plant at the Mission Concentrator of the American Smelting and Refining Company, some 20 miles south of Tucson, Arizona in the Twin Buttes mining area, has been in operation slightly over a year. The plant produces a molybdenite concentrate a copper concentrate and, at times, a zinc concentrate. An intensive test program of over three years was conducted at Mission to make the recovery of molybdenum economic. Briefly it was found necessary to make a scavenger concentrate in the copper mill before it was possible to recover economic quantities of molybdenite. By so doing there were resulting additional recoveries of copper, silver and zinc. This program resulted in the design and construction of the existing plant. A paper by the authors discussing the test work and the design was presented at the, October 1965 meeting of the American Mining Congress in Las Vegas, Nevada, by Mr. Wayne Bossard.

Jan 1, 1966

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By David L. Giles

The alkalic igneous province of Montana consists of centers of laccolithic and stock-like intrusive complexes with associated sills, dikes, and breccia pipes (e.g., Judith, Highwood, Little Belt Mts.); isolated plug-like mafic bodies (e.g., Smokey and Eagle Buttes); and clusters of kimberlitic diatremes and ultrabasic dike swarms (Missouri River Breaks). The province extends in a belt throughout central Montana from the North Absaroka Range in the south to the Sweetgrass Hills on the Canadian border. Intrusive activity ranged in age from Late Cretaceous to late Miocene, peaking at about 50 m.y, ago. Diverse types of significant epithermal gold mineralization occur at many of the laccolithic centers. This mineralization took place in large part during the waning stages of, or following, igneous activity. Large remnant travertine blankets in the region attest to comparatively recent hydrothermal activity. The quartz-pyrite-gold mineralization ranges from igneous- hosted stockworks or fracture sets (Zortman-Landusky and Neihart districts) and breccia pipes (North Moccasin Mts.) to replacement zones in flanking and upwarped Madison Group limestone (Gilt Edge and Kendall districts). The latter are mostly localized by intraformational solution breccias in the upper Madison, notably near porphyry contacts. Gold mineralization in the province was accompanied by varying amounts of silver, base metals, sulfosalts, and tellurides, with quartz, fluorite, carbonate, and barite and gangue. Gold occurs as auriferous pyrite, sylvanite, or in native form. Since the 1880's, primary gold production from numerous scattered deposits in the Judith, Moccasin, and Little Rocky Mountains, along with byproduct gold from the Neihart silver district (Little Belt Mountain), has totalled around 2 million oz. The major deposits were in the 1-2 million ton range at an average gold tenor of 0.3-0.6 oz per ton. Most of the ore was mixed oxide or carbonaceous sulfide ore and was treated either by amalgamation or by roasting-cyanidation. Current activity includes heap-leach operations on bulk- tonnage low-grade (approximately 0.03 oz per ton) ores at Zortman-Landusky, and several small-scale, experimental leach or mining operations on carbonaceous replacement ores, as in the Kendall district and Spotted Horse mine. Current exploration efforts for gold are focused not only in the old established districts, but also in and around other alkalic centers, which have been unproductive to date, such as the Crazy Mountains, Sweetgrass Hills, and Bearpaw Mountains. Target concepts in these efforts are porphyry-hosted stockwork or disseminated gold ores and Carlin-type replacement lodes in the flanking Madison or other favorable carbonate units.

Jan 1, 2013