Search Documents

By Egon Pohl, Peter Eckl, Friedrich Steinhäusler, Johanna Pohl-Rüling

RADON EXPOSURE AND CARCINOGENIC CELL TRANSFORMATION The highest radiation burden to miners is due to inhalation of radon and its short-lived decay products. The quantification of the risk associated with this radiation burden is complicated by modeldependent lung dosimetry, insufficient accuracy of past human exposure data as well as lacking knowledge about potential synergism of various carcinogens. Nevertheless, it is evident from epidemiological studies of miners that inhalation of elevated levels of radon daughters is correlated with increased lung cancer incidence (UNSCEAR, 1977). The situation is further complicated by the lack of reliable data on the biological variability of the latency period for the development of lung tumor under varying exposure conditions. At present information on variation with age is scarce, however, it is indicated that the excess lung cancer rate for workers exposed to high radon levels is considerably higher, if exposure occurs at ages over 40 years as compared to under 30 years of age (Sevc, Kunz, Placek, 1976). Furthermore, latency period is shorter by 6 - 7 years for smokers exposed to elevated radon levels than for non-smokers (Fry, 1976). Analysis of US- and CSR-uranium miner data revealed that the mean latency period is in the order of about 15 years (Jacobi, 1973). These uncertainties, together with medical diagnostic shortcomings, lead to the dissatisfying situation that at present the detection of radon induced injury of mining personal is primarily the assessment of the endpoint, i.e. radiation induced cancerous transformation of lung cells with typically less than 10% chance for recovery. Therefore it would be advantageous to develop practically applicable diagnostic aids to indicate already early precancerogenic changes of cell characteristics. This would permit the identification of specific population groups at increased risk for the development of lung cancer, thereby increasing the chances of more successful medical treatment. Despite continuous improvements in the reliability of test methods for the diagnosis of cancer cells there is still need for techniques, which enable the detection of transformed cells before the onset of invasion of the host organism. It is generally recognized that the transformation of a cell into a malignant state leads to a change of the cell surface, indicating a correlation between membrane-specific immunological properties and loss of growth control. Surface alterations on cells appear to be responsible in part for the malignant state and are not simply secondary effects of the transformation (Schnebli and Burger, 1973). Furthermore, membranes of cancer cells differ significantly from those of normal cells, particularly, in permeability properties (Rastogi, 1976). In dying cells, proteins, glycoproteins, peptides, aminoacids and their breakdown products are released, which block the permeation of the membrane itself. A mammalian cell can be considered as a 3-phase system (interior, boundary, environment) with the membrane forming a heterogeneous barrier between two subsystems. Under normal circumstances a difference of chemical potential is maintained on both sides of the membrane, causing an ion gradient across and fixed surface charges on the membrane. This results in a membrane resting potential (MRP) between cytoplasm and the bulk medium. It has been shown that MRP is a highly sensitive indicator for cellular reactions due to physical, chemical and biological agents, particularly whenever phenomena of transport and ion gradients as well as permeability are involved (Redmann, 1980). The primary interaction of the agent "ionizing radiation" with any form of living matter occurs at the cellular level. The component with the highest hit probability is the cell membrane. In the study presented MRP-changes of human cells were investigated with simultaneous measurements during irradiation and post-irradiation intervals up to six days. Furthermore, the suitability of MRP-measurements of human cells was tested as an indicator for early changes of cellular properties prior to the histological confirmation of carcinogenic transformation. EXPERIMENTAL METHODS Lung cells The biological specimen used were cultured human lung cells and human lung biopsy samples. Monolayers of lung fibroblasts (W138) were grown in petridishes using conventional culture techniques. In addition, transformed lung cells (W138SV13, subline 2RA) were used applying similar culture methods. All petridishes were incubated at 37°C and only cells in logarithmic growth phase were used. Freshly excised lung biopsy samples were obtained from randomly selected male and female patients (20 cases), where suspected or unclear malignancies were indicated by clinical or X-ray observations. At the time of sampling 80 % of the patients were or had been smokers in the past. The samples were taken by means of a stiff bronchoscope introduced into the trachea under local anasthesia with 1 % Novesinsolution (preparation with Atropin and Pantopen). This permitted the observation of both main bronchi down to the segmental bronchials. From each patient two tissue samples were excised from the mucusepithelial layer under visual control with fiber optics and transferred immediately into 1 % NaClsolution. One sample was taken from the suspected

Jan 1, 1981

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By L. A. Garfield

Since the start of mining operations at White Pine in 1953, over 22 miles of drifts have been driven for the purpose of developing the ore body. The drifts, normally driven in multiples of three or five headings, serve as conveyor belt routes, ventilation ducts, equipment and haulage roads, and initial access to mining blocks. Development openings in the flat-lying, bedded ore body are driven in rectangular section from 16 to 32 feet wide and from 8. 5 to 16 feet high. The floor level normally coincides with the bottom limit of the chalcocite values and the roof or back is carried at the most competent stratum adjacent to the top of the ore. A development front consisting of five headings and associated crosscuts is advanced at an average rate of about 100 feet per month using conventional drill and blast techniques and equipment. The cyclic nature of the functions involved in driving the openings and the need to include them in production schedules preclude significant improvements in advance rates using current drill, blast, muck, and haul sequencing.

Jan 1, 1969

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come but are just around the corner. This article presents a vision of this upcoming revolution in the earthmoving industry. This vision includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For the industry to realize maximum benefits from the information age, it must have a vision of the future that is shared by technologists, machinery producers and miners. History of the information age During the 1970s, the information age revolutionized retailing, starting with the grocery business. By using bar codes and laser scanners, individual items were connected to the information world of computers and communications. Once this connection was made, the data on what an item was and where and when it moved became valuable information for inventory control and marketing. Not only was the information valuable, it was easy and inexpensive to collect and manipulate. The effort required to provide the consumer with the right product at the right time was reduced. Costs went down and customer satisfaction went up. But there were casualties of this revolution. Many inventory counters lost their jobs. There were also equipment casualties. Cash registers that could not interface with the digital world were discarded long before the end of their useful life.

Jan 1, 1994

By G. S. Austin, L. A. Brandvold, J. Renault

A series of tests were run on soil samples collected near the site of a Socorro, NM lead smelter that was abandoned more than 98 years ago. Three 30.5- x 30.5-m (100-X 100-ft) squares provided 13 samples each. As described in Part I (this issue), each sample was divided into seven splits according to particle size. A mineralogical examination of the fine-size fraction of Pb-contaminated soils failed to reveal crystalline Pb compounds. These authors conclude that Pb is present as amorphous phases or is adsorbed on the surfaces of soil particles. Site vegetation contained elevated Pb levels that increased with increasing Pb amounts in the soil. However, the biological absorption coefficient (BAC) indicates that some of the site's Pb is unavailable, or the plants are able to limit their uptake. Of the vegetation tested, rabbit bush showed the greatest increase of Pb levels in its roots, whereas levels in creosote were highest in the foliage. In cactus, the Pb levels varied. The amount of Pb due to dust incorporated in plant tissue is almost negligible compared to the amount absorbed through the plant vascular system.

Jan 1, 1994

By Ronald J. Doll, John Elkin, M. P. Evans

The application of "Alignment Free” right angle shaft mounted drive systems offers improved reliability and reduced costs for surface and underground belt convey- ors. Comparisons to conventional approaches will cover installation, operating, maintenance, and spares inventory cost savings. Various options for belt acceleration and load control on fixed and variable length (booster) belt conveyors will be reviewed for operating performance, reliability, and total cost. Lastly, a case study of a successfully operating installation will be highlighted.

Jan 1, 1996

By Thomas O’Neil

Part 2 of this article continues with a discussion of features that distinguish contemporary investment analysis in mining from earlier methods. Part 1 traced the evolution of evaluation methodology from the traditional and discounted cash flow methods to the present. Quantitative investment models of the past 20 years played an important role in mine evaluation, but a new integrated approach to mine investment decision-making is now developing because of growing economic, technical, and political uncertainties. One of those uncertainties -inflation-was discussed in Part 1. Increased Risk At a time when mineral production technology and analytical evaluation tools have never been more sophisticated, it may seem anomalous to claim that mining ventures are riskier. Whereas technical risk has, indeed, been notably reduced, business risk the chance of a major loss due to market factors-has increased. This has been caused by two factors: the rapidly rising capital requirements of new projects and increasingly unpredictable future economic conditions. These difficulties are compounded by the long lead times of large, new mining projects. Rising Capital Requirements A $100 million investment is no longer considered to be a large mining project in most cases. For a large metal mining project, the total cost of the concentrator alone can exceed $100 million. Amoco Minerals' Thompson Creek molybdenum mine being developed in Idaho will cost over $350 million, for a relatively modest sized (23-kt/d or 25,000-stpd) ore operation with no extraordinary features. For a major grass roots copper operation producing blis¬ter or refined copper, the capital requirements are billions of dollars, not millions. Project costs are higher for two reasons. One, the projects themselves are larger; and two, the capital cost per unit of production is rising rapidly. Projects are larger because lower grade ores, yielding smaller margins, must be mined in greater volume-particularly in view of the high fixed costs of modern technology. When analysts contemplate any capital project, an important consideration is the minimum economic size of the facility. This is the smallest size that can be built and still be competitive on a total unit production cost basis. In the conventional copper smelting business, for example, a production rate of at least 91 kt/a (100,000 stpy) of blister copper is about the absolute minimum for reducing unit fixed costs to competitive levels. Clearly, many variables affect the minimum economic size of a mining facility, but with few exceptions that size continues to grow. Unit capital costs of new mining projects also are continuing to rise. The accompanying table shows that the capital costs in primary copper production have risen faster than the cost of living. Of particular note is the capital charge of over $1.70/kg (77411b) required for a new, fully integrated facility in 1981. Thus, the mid-1982 copper price would not even cover the cost of capital for a new copper producing complex without considering the direct operating costs for such a facility. The breath-taking costs of new mining projects are caused by factors such as increasingly complex technology, the rising social costs of creating attractive living and working conditions for employ¬ees, and the expenditures re¬quired for environmental protec¬tion. For whatever reasons, how¬ever, unit capital costs in mining continue to exhibit staggering growth rates. Future Economic Conditions Risk is not only a function of the size of the potential loss-an im¬portant measure of which is the capital intensity of mining dis¬cussed above-but also of the like¬lihood of incurring the loss. It is here that the ever increasing lead times of mining projects and the glaring limitations of economic forecasting are so important. In comparison to nearly all other in¬vestments, mining has more capi¬tal at stake for a longer period of time before commercial uncer¬tainty is resolved by distant eco¬nomic conditions that are subject to high forecasting errors. A sobering example of the pre¬ceding points occurred with the Lakeshore copper mine in south¬ern Arizona that Hecla Mining Co. undertook to finance and manage in 1969. The project was a joint venture of Hecla and the El Paso Natural Gas Co. and included two mines-one producing oxide ore and a second in the sulfide zone¬and a complex processing facility producing both electrowon cop¬per cathodes and copper precipi¬tates. The project originally was

Jan 12, 1982

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

Due to the relatively remote location of the St. Anthony Mine, the high cost of transportation and milling, plus the low grade nature of the deposit, the United Nuclear Corporation began investigating methods of mechanical upgrading approximately eighteen moths ago. This investigation culminated in the installation of Model 17 and Model 18 ore sorting machines. The machines are marketed in the United States and Canada by Ore Sorters of Canada (Ltd.). The installation of this advanced technology will enable United Nuclear Corporation to fully realize the residual potential of St. Anthony.

Jan 1, 1979

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969