Search Documents

By Toru Nakao

Fujiwara Quarry had been operated by the "Glory-hole Benchcut" mining system. But because it became difficult to meet the expanding demand by this system, "Central- shaft MCP" mining system was introduced in 1979. This MCP is equipped with a hydraulic walking system manufactured for the first time in Japan. Nowadays "Central-shaft" mining is the common method at limestone quarry in Japan. In this method crushing facilities are usually installed at the bottom of the shaft. But at this quarry, MCP was adopted and installed on the quarry surface. Many MCPs are operated in foreign countries, but in Japan few examples exist. Normally, Japanese limestone deposits lie in high mountains, which is obviously inconvenient for MCP to walk in and around the quarry. This difficulty, however, was overcome at this quarry, and MCP has been operated satisfactorily and efficiently for about 2 years after it was installed. In order to overcome the difficulty, in "Cen¬tral-shaft MCP" mining system, two mining methods are employed, the one is "SLICE-DOWN" mining method, and the other is "BLOCK-CUT" mining method.

Jan 1, 1982

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit' data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO's increased geochemical activity.

Jan 1, 1982

By Duk-Won Park

The stability problems of back- filled spoil banks became more important since the Federal Surface Mining Control and Reclamation Act of 1977 was enacted. The material properties of spoil banks were categorized as the first part of the study and spoil slope stability was evaluated using computer programs as a second part. Emphasis was placed on the effects of natural barriers, which is required in the federal law.

Jan 1, 1982

By S. K. Kawatra

With the increasing importance being placed upon modernizing the coal industry as a result of recent developments in the international energy balance, computer control has been and is being instituted in many coal cleaning plants. Control techniques that are well established in many base metal industries have been adapted to coal washing. Essential to any control scheme is an accurate measure of the parameter which is to be controlled. A sensor is required that will provide information both quickly and precisely. In fine coal circuits, the critical parameter that must be measured and controlled is the per- cent ash contained in the clean coal product and tailings. Measuring the ash content of these slurry lines on a continuous basis enables the operating conditions in the circuit to be adjusted so as to obtain optimum separation efficiencies at all times. An on-line ash monitor has been developed and tested at Michigan Technological University which is capable of making percent ash and percent solids determinations instantaneously. Two radioisotopes are employed in this system to generate signals that can be related to the density and the ash content of the slurry. Such data provide a means to execute a short term control strategy.

Jan 1, 1982

The effect of addition of a flotation collector (dodecylammonium chloride) on grinding of quartz has been studied. The data obtained are correlated with the results of tests conducted under similar chemical conditions to study influence of these additives on relevant basic sub-processes (primary breakage, pulp fluidity, and dispersion and flocculation of ground products). Such correlations suggest that the role of chemical additives in grinding is determined by their cumulative influence on the above mentioned basic properties of the system.

Jan 1, 1982

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By M. Ashraf Mahtab

In Louisiana salt mines a sudden erruption or outburst of salt and gas occurs when the heading face approaches a pressure pocket (altered salt with high pressure gas). The resulting cavity is semi-ellipsoidal, reaching lengths of 50m or more. Potential risks from the outbursts include loss of life and equipment. A gas outburst is initiated by "disking" of the salt in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement to boundaries of the pressure pocket.

Jan 1, 1982

By A. J. Richardson

Before the development of the underground stoping and mining costs can be considered, certain facts about the ore body, the proposed mine, markets, etc., must be known or determined. In the case to be studied, the zinc-lead mineralization occurred with a narrow vertically dipping structure of undetermined length and vertical extent. Exploration completed to date has revealed 6.5 mil¬lion st t of proven reserves. A further 820,000 st of in¬dicated reserves has been outlined and this tonnage is considered capable of being expanded by a factor of approximately four after more detailed drilling. After studying the market conditions and completing a very preliminary feasibility study, it was decided that production would be 730,000 stpy (or 2000 stpd) of ore. First year production would be at the rate of 1500 stpd. The main design criteria for the selection of the min¬ing methods are minimizing surface subsidence, maxi¬mum recovery of the ore body, maximum degree of grade control, maximum productivity, and safe working conditions. Two basic extraction systems are considered capable of meeting these requirements: mechanized cut¬and-fill stoping and sublevel long-hole stoping with filling. The primary development system of the mine has been designed to give maximum flexibility in stoping systems and layout and to permit changes if considered necessary as a consequence of actual production ex¬perience. At the present time, access to the mine is by a circu¬lar concrete lined vertical shaft, 16 ft diam, sunk to a depth of 1380 ft. Two exploration levels have been driven within the ore zone at depths of 165 and 1246 ft below the surface outcrop. The development to date had the objective of sampling the mineralization and produc¬ing detailed information on the outline of the ore body and the distribution and controls of zinc and lead values. In an attempt to satisfy the basic design criteria for the mine, it was decided that production would be best achieved by a combination of 40% sublevel long-hole stoping and 60% cut-and-fill mining. Costs of exploration and capital development of per¬manent underground facilities are normally written off over the life of a mine. Production expenditures, on the other hand, are of a temporary nature and are normally charged as and when incurred as an operating expense. Reasonably accurate predictions of mine production costs can be built up from engineering design and estimates of individual mine activities for ultimate inclusion in the comprehen¬sive data required for financial decision making. The simulated operations can be costed on a detailed basis in the form of a monthly operating budget. The budget format can be generalized or detailed, depending upon the scope of the project. However, ex¬perience suggests that a fairly detailed format has the advantage of assuring that all significant cost items are included. For underground costing it is suggested that the budget structure include five major cost centers (i.e. development, diamond drilling, ore extraction, hoisting/ transportation, and general mine expense). These in turn are detailed under numerous subheadings. The mechanism for compiling an operating budget will be illustrated. Because of its relative simplicity, ore extraction under sublevel long-hole stoping has been chosen for illustration. All other activities, simple or complex, can be estimated in similar fashion. BLOCK AND STOPE DEVELOPMENT Long-hole blocks, used where advantageous, will be up to 250 ft in height, depending upon the vertical con¬tinuity of the mineralization, and approximately 300 ft long. Drawpoints will be at 36-ft intervals and serviced by loading crosscuts driven from a footwall drift parallel to and close to the ore zone. Pillars between the stopes will be 50 ft wide. Stopes will be drilled off with vertical rings of blastholes drilled from sublevels approximately 60 ft apart vertically. This drilling will be done by percussion drilling machines (31/2 in.) mounted on a trackless drilling rig. Load¬haul-dump (LHD) equipment will be used to move broken ore from the drawpoints to the orepass connecting to rail haulage systems. On completion, long-hole stopes will be backfilled to prevent caving and to facili¬tate later pillar removal. From a planned stope layout, a forecast of produc¬tion and development is made in Table 1. Table 1. Block Tonnage and Stope Development Quantity Ore Waste Total ore block 375,000 st 2 stopes 310,000 st 1 pillar 65,000 st Access crosscuts, 4 at 100 ft 400 ft Drill sublevel drifts, 6 at 300 ft 1800 ft Stope raises, 3 at 250 ft 750 ft Undercut sublevel drifts, 2 at 300 ft 600 ft Loadout crosscuts at 35-ft intervals 550 ft 100 ft 3300 ft 500 ft Total development footage 3800 ft Tons per ft of development 987 st

Jan 1, 1982

By D. E. Munson, H. J. Sutherland

Empirical methods for describing the shape of the subsidence trough over coal mines in Europe are tested against field measurements of subsidence over longwall panels in the United States. The graphical methods developed by the National Coal Board in the United Kingdom do not correlate well with the U.S. measurements; however, the profile functions typically used on the Continent give quite acceptable fits to the data. In the case of two longwall panels mined at Old Ben No. 24 in Illinois, a trigonometric profile function appears the best choice; in the case of two longwall panels mined at York Canyon in New Mexico, an error integral function is somewhat superior. Analyses of subsidence development curves show that rate effects occur. A comparison of fitting parameters establish influence functions as an important methodology for future analysis. In conjunction with the evaluation of empirical methods, an analytic model based on material failure and bulking was developed. A key element of the model is the void-volume distribution function which establishes a mechanism for transfer of significant amounts of the mined volume to the surface. Preliminary calculations demonstrate the features of the model and illustrate close correlation to physical observations in the field. Moreover, centrifuge models simulating the subsidence process have been used successfully to demonstrate the dominant or key failure modes necessary to the analytic model. General features of the centrifuge simulations and model calculations correlate well.

Jan 1, 1982

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982

By Graham A. Mathieson

A detailed breakdown of capital and operating costs is an essential element in the planning and evaluation of any mining project. The OPCOST System was developed by Golder Associates to provide mining engineers with the facility to synthesize detailed cost estimates for all aspects of an operating or potential open pit mine. The system can also be applied to underground mines equally as well. Such estimates can be prepared at a variety of levels depending on the detail required by the project. The OPCOST System is a suite of computer programs linked through a common hierarchical data base. It simulates the thought and reasoning processes within the quantity takeoff and cost estimation phases of a mining project. The system was developed as a mining cost engineering tool on the basis that it would have to satisfy a variety of purposes, namely:

Jan 1, 1982

By C. W. Fitzgerald

INTRODUCTION Continuous mining machines are used in regular flat ore beds having uniform thickness. Since coal is the most common type of material occurring in such beds, most continuous miners are used for the extraction of coal from underground mines. The first continuous mining machine for under¬ground coal mining was introduced in 1948. In one machine, the continuous miner combines the functions performed by a conventional face drill, a cutting ma¬chine, and a loading machine. It breaks or digs the material out of the surrounding solid and transfers the material back through the machine chassis by means of a chain conveyor. The conveyor carries the material to a haulage system, usually a rubber-tired vehicle known as a shuttle car. Generally, continuous miners are used in seam heights from 890 to 3660 mm (35 to 144 in.). For seam heights of 1070 mm (42 in.) or less, the haulage system may be a multiple-bridge conveyor or battery-powered tractors that haul low-bed trailers. Proj¬ects are being undertaken by private industry and through government contracts to develop a continuous haulage system for all seam heights. As of 1976, the majority of continuous miners were of two types. The first type is the drum miner, which mounts the cutting elements on a series of drums across the cutting head of the machine, sometimes using a cutting chain to cut clearance for the gear drive. In the drum-type machines, the cutting head rotates parallel to the material face. The second type is the auger miner, which utilizes cutting elements mounted on two auger-type cutting heads. One head is located on each side of the machine, with the heads mounted per¬pendicular to the material face. Chain-head ripper-type miners/miners having rotary cutting elements with oscillating motion and twin-head boring-type miners have all been popular within the last 15 years. Although these are considered obsolete, some machines are still being supplied for specialized applications. GENERAL DESCRIPTION This chapter describes only continuous mining ma¬chines available as manufacturers' production models as of September 1976. Figs. 1 through 11 illustrate some typical machines currently in use. Cutting Elements The cutting elements are the interface between the machine and the material being mined. In describing the cutting elements, consideration must be given to the differences between the drum- and auger-type machines, the bit-tip speeds, and the bit types. Drum-Type Continuous Mining Machines: Three of the four principal manufacturers of drum-type miners use multi-motor designs that provide separate a-c motors for driving the cutting elements. Gear trains are used to reduce the speeds of the motors to the rotational speeds of the cutting elements. One of the three suppliers drives the cutting elements of its low-seam models with a heavy-duty drive chain that is equipped with cutting bits; all other functions of this machine have separate motor drives that are either electrical or hydraulic. The fourth principal manufacturer generally provides two a-c electric motors, utilizing gear reducers, drive shafts, and hydraulically operated engaging clutches to power all of the operating functions, including the cut¬ting elements. Some drum-type miners use trim chains, equipped with cutting bits, to cut clearance for the gear drives. These trim chains vary from two 305-mm (12-in.) chains to one 760-mm (30-in.) chain per machine, de¬pending upon the manufacturer's design concept. In all machines other than the low-seam models that use chains to drive the heads, the trim chains are driven by sprockets on the drive shaft of the final cutterhead drum; therefore, the trim chains are not used for power trans¬mission to the cutting elements. In addition to cutting clearance for the gear drives, the trim chains provide uniform bit spacing all the way across the head and assist in moving the cut material to an area where it is either loaded directly into the miner's conveyor or is easier to load into the conveyor. On a drum-type mining machine, the cutting ele¬ments all rotate from the top to the bottom. Therefore, the recommended procedure is to raise the cutterhead to the maximum seam height, sump the entire machine forward to maximum depth by means of a crawler drive, and then shear downward until the cutter elements reach the floor level. The maximum sump depth varies ac¬cording to the drum diameter, the type of material, the floor conditions, and the operator's abilities. It normally varies an average of 460 to 760 mm (18 to 30 in.). Cutter drums are supplied with two types of cutting bit holders. Weld-on holders are attached permanently. Pin-on holders are replaceable at the face. Cutter-drum diameters over the bit tips vary from 660 to 965 mm (26 to 38 in.), depending upon the chassis height of the machine and the range of cutting heights. Auger-Type Continuous Mining Machines: As cut-

Jan 1, 1982

By G. Robert Frey

INTRODUCTION This chapter on underground rotary drills briefly describes the equipment features, selection or applica¬tion criteria, safety features, and relative costs of both face and roof drills. After a brief description of the basic components, the application, safety, and cost con¬siderations will be explored. ROTARY DRILL COMPONENTS As illustrated in Fig. 1, an underground rotary drill consists of five basic components. These components are the energy system, chassis, boom, feed assembly, and operator's station. Energy System The energy system of a typical underground drill con¬sists of an electric motor, driving a hydraulic pump or pumps. Usually, the drill is equipped with a cable reel to store the trailing power cable from the portable power center in the mine. A simple control box is supplied to house electrical switchgear and protective devices. In addition to the pump, the hydraulic portion of the energy system includes the hydraulic cylinders, hydraulic tram motors, relief valves, control valves, etc., necessary to actuate the various machine functions. Chassis The chassis provides the frame or support structure for the other four basic components of the drill. Fre¬quently, it incorporates an oil reservoir for the hydraulic system. The chasis provides the support for the trans¬mission, which drives rubber tires or, in the case of some foreign machines, the crawler tracks. The steering link¬age and steering tires also may be considered as parts of the chassis. Boom The boom is the structure that supports the feed assembly; it is either hinged or pivoted on the front of the chassis. Hydraulic cylinders on the boom are used to lift or swing the boom relative to the chassis and to swivel or "roll" the feed assembly. Feed Assembly The feed assembly is made up of the support struc¬ture with an integral thrust mechanism, a rotation unit, centralizers to stabilize the auger, and a hose handling arrangement. In addition, most drills have an extension frame with a tilt device to aid in positioning the feed. Operator's Station The operator's station is the area from which the miner operates the drill. UNDERGROUND ROTARY DRILL APPLICATIONS Underground Face Drills Underground face drills are used in mining opera¬tions that utilize the conventional mining system. The face drill is used to drill holes in the exposed face of the material, and the face is then "shot" by means of explo¬sives or high pressure air. The loose material then is ready for loading and transporting from the face to the preparation plant. Typical specifications for under¬ground face drills are listed in Table 1. Certain parameters should be established as to where the drill is to be used and what is expected of it. To create an awareness of some of the considerations that too often are overlooked, some questions are listed that should be asked in conjunction with the selection or application of the proposed drills. Energy System: Can the drill be supplied with the proper voltage to match the available or proposed elec¬trical power system of the mine? Is the system 250, 460, 500, 550, or 950 v; dc or ac; 3-phase; 60 or 50 Hz? Is the drill equipped with an adequate electric motor to handle the proposed duty cycle? Typical motor power on a single-boom drill would range from 25 to 40 kW (35 to 50 hp); the nominal power for a dual-boom

Jan 1, 1982

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation's No. 1 mine in northern West Virginia.

Jan 1, 1982

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By Tore M. Larsen

The Rødsand Gruber mining company is a subsidiary of the Norwegian industrial corporation Elkem AS, and its mine is situated in the northwestern part of southern Norway. The ore from this mine is a relatively low grade, magnetite ore with a small amount of vanadium. The ore bodies are very irregular in shape, resulting in a high amount of waste rock intrusion in the stopes. The annual underground production in the mines is approximately 1 million t. Because of varying dimensions of the ore bodies, both transverse and longitudinal stopes are employed. The inclination of an ore body is usually 1.04 to 1.59 rad (60 to 90°), and the horizontal width varies up to 100 m. Sublevel stoping has been the traditional mining methods in this mine. Until a few years ago, the ore was primarily blasted using horizontal blasthole fans drilled from Alimak raises. Recently, however there has been an increasing demand for a les expensive mining method. Alternate systems were considered, and finally a method based upon large blasthole stoping was found to be the most suitable. GENERAL LAYOUT The general layout of a stope is shown in Fig. 1 As with all the figures in this chapter, only the prin¬ciples of the method are emphasized and the details may not be valid for any particular site in the mine. In transverse stopes, the horizontal width of the ore determines the length of the stopes. The average length is approximately 50 m, the width of the stopes is 20 m, and there is a 10-m wide vertical pillar between. The distance between the main levels is 60 m. Usually a horizontal (sill) pillar 10 m thick is left below the mucking level. Each stope is first undercut along the entire stope length. This undercut is made with 50.8-mm (2-in.) diam drill holes in a fan pattern. At the moment this is being done by a trackless Atlas Copco Promec jumbo equipped with two Cop 130 pneumatic rock drills. The drill drift is 4 X 4 m, and the crater is 20 m high. This leaves a 36-m stope height to mine with large blastholes. To achieve a fair portion of vertical drilling withlarge blastholes, there are two parallel drill drifts at the top of each stope. These drifts are 4 m high and 9 m wide, separated by a 4-m wide pillar in the middle of the stope. To ease the drilling of perimeter holes, the drifts extend 1 m into the vertical pillar on each side of the stope. The pillar will thus be only 8 m wide on the drill drift level, but 10 m wide down the rest of the stope.

Jan 1, 1982

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982