Search Documents

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982

By G. L. Hohmann

The Waste Isolation Pilot Plant (WIPP) project is authorized by legislation to provide a demonstration of the safe disposal of radio- active wastes generated by the national defense programs and activities of the United States. The U.S. Department of Energy (DOE) is proceeding with the implementation of the WIPP project in accordance with the "Department of Energy National Security and Military Application of Nuclear Energy Authorization Act of 1980" (PL 95-164).

Jan 1, 1982

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By R. V. Ramani

This paper is based on the thesis that the demand for computer-oriented mining engineers will continue to sharply increase in coming years. It presents the philosophy behind the development of a mine systems engineering program at The Pennsylvania State University. The paper discusses the current status of mining engineering education and the problems encountered in integrating extensive computer background and education into a traditional mining engineering program. The paper analyzes the interrelated roles of research, graduate studies, and continuing education in developing a comprehensive program of study. It is hoped that this program philosophy will be useful to other institutions which are contemplating new programs and courses in emerging technologies.

Jan 1, 1982

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By Horace M. Varner

Under sponsorship of the USBM and later of the DOE, a new type of rotary rock drill has been developed by The Bendix Corporation. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. This drill allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. The paper discusses various applications and experience for the flexible drill system in coal mining, metal/nonmetal mining, and for general civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1982

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982

By Richard L. Stein

INTRODUCTION Increasing a miner's chance of surviving a disaster requires advance planning for emergencies, adequate training of personnel, and the provision of proper survival equipment. It is extremely important that fires and toxic gases be detected early, and that warning systems such as stench, audible and visual alarms, and communications systems be provided to allow timely escape. However, situations do occur where timely warning is not provided and immediate escape is not possible, regardless of the precautions that are taken. Under such circumstances, a combination of new per¬sonal protective devices and old techniques can provide protection that is adequate to save a miner's life. SELF-RESCUE EQUIPMENT Self-rescuers are devices which provide a short-term supply of respirable air under the potentially lethal con¬ditions following a mine disaster. Functioning either as filtration devices for the elimination of carbon monoxide (CO) or as oxygen supplies, self-rescuers allow an endangered miner a limited amount of time in which to effect an escape or reach a place of temporary safety. Carbon-Monoxide Self-Rescuers For almost 50 years, filtration self-rescuers have protected miners' lives following explosions or fires. Designed to eliminate carbon monoxide from inhaled air, the first of these devices was approved in the 1920s and has evolved into the two units that are approved today-the Mine Safety Appliance (MSA) W-65 and the Draeger 810. Both of these units rely on the cata¬lytic conversion of very toxic carbon monoxide to rela¬tively safe levels of carbon dioxide (CO,). As shown in Figs. 1 and 2, both of these filtration self-rescuers operate in the same manner. On inhalation, the mine air passes through both coarse and fine filters that remove the dust, preventing the dust from coating the chemical beds or entering the miner's mouth. The air then passes over a drying agent that removes water vapor; this is required to prevent the water vapor from poisoning the catalyst. Subsequently, the dried air passes over the Hopcalite catalyst, where carbon monoxide is converted to carbon dioxide. Then, the air passes through a heat exchanger that reduces the temperature of the inhaled air. Finally, the air is inhaled by the user. Air exhaled by the user passes through the heat ex¬changer and exits the device through an expiratory valve. Both units of this type are subject to certain limita¬tions: 1) The units do not protect the user against oxygen¬deficient air; when air is inhaled through this type of self-rescuer, the device only removes the carbon mon¬oxide. If the mine air contains less than 15% oxygen, anoxia is inevitable. Symptoms of anoxia include dizzi¬ness, shortness of breath, quickened pulse, and deeper and more rapid respiration while the victim is at rest. During heavy exertion such as would be expected dur¬ ing escape efforts, a 15% oxygen level can cause loss of consciousness. 2) The units do not protect against excessive levels of carbon dioxide. Available data on carbon monoxide and carbon dioxide concentrations following explosions or fires are limited, but there are indications that the carbon monoxide concentration can rise to 2% and the carbon dioxide concentration can reach 5 or 6% of the mine air (by volume). In some situations, the in¬haled air could contain up to 6 or 7% carbon dioxide. At a carbon dioxide concentration higher than 2%, breathing patterns can be affected adversely. At a con¬centration of 6 or 7%, the effects include severe respira¬tory distress, with unconsciousness resulting from exer¬tion such as that needed for escape activities. 3) The units do not protect against high inhalation temperatures. The catalytic oxidation of carbon mon¬oxide to carbon dioxide is an exothermic reaction that evolves a large amount of heat. As the carbon monoxide concentration increases, the temperature of the inhaled air also increases. Available data show that above 1.5% carbon monoxide, the air inhaled through some self¬rescuers can be as high as 90°C (194°F). At those

Jan 1, 1982

By James E. Kolesar

An essential prerequisite to expanding the application of longwall mining techniques in the United States is the development of a better understanding of the mechanics of rock mass deformation near the mined seam, in the inter- burden and at the surface. The results of studies of this type will provide a basis for the development of empirical and/or numerical modeling techniques to predict the rock mass response to mining both near and far from the mined seam. This will lead to improved gate and panel design, resulting in maximum recovery, increased productivity, as well as provide a mechanism for assessing likely surface effects induced by long- wall mining. Presented here is the instrument plan to be used at Kitt Mine No. 1 in the study of rock mass response to two adjacent longwall panels.

Jan 1, 1982

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By N. J. Ferguson

An upsurge in demand for Australian coal has seen a much needed programme for a new generation of coal ports. This paper discusses design concepts in planning a large modern terminal, with the 25 Nt/a Port Kembla and the 50 Mt/a Newcastle facilities as practical examples. The need is emphasised for a studied Master Plan, in-built materials handling flexibility and staged development. Trends in bulk ship design and loading methods are noted. Features of these Australian designs include methods of dealing with poor ground conditions, functional civil engineering for environmental protection and optimal marine structure designs.

Jan 1, 1982

By Dwight R. Coles

The solving of complex metallurgical flowsheet calculations by hand is, at best, a tedious job which often proves that engineers, too, make mistakes. The high cost and long lead time associated with manual flowsheet solutions have led several organizations involved in research, development and construction of extractive metallurgical processes to search for computerized systems which will solve flowsheet calculations. Although design flowsheet programs have been developed by the chemical industry, the ability to solve flowsheets involving particulate solids is usually overlooked. A new computer applications system has been developed at Fluor Mining and Metals which has been designed to accommodate the type of design flowsheets required by the minerals industry. By employing the sequential modular computation technique, a library of metallurgical pro- cessing routines may' be accumulated which are used by a universal executive system. This technique enables rapid solution of new process) .flow- sheets with only a minimum of additional programming effort. The implementation of the FLEXMET flowsheet solution system is the subject of this paper. Some of the major features of the system which are examined include interactive input data handling, automated flowsheet calculation order arrangement, flexible accomodation of unit operations models and advanced management of recycle and specification control calculations.

Jan 1, 1982