Search Documents

By Donald J. Worth

When Eugene Bailey asked me to contribute to this session on "Canadian exploration - 1976", it took a little coaxing before he got me to agree. My immediate reaction was, what could i say about Canadian exploration that already had not been said a hundred times in the past few years; secondly, why include a banking person in such a discussion? Everyone knows banks only come into the picture after the discovery has been made and feasibility well established and validated. Rather than wrestle with these misgivings, I decided to take the easy way out and go on blind faith in Eugene - that is, he asked me so he must think that I could come up with some useful thoughts and at least touch upon some of the pros and cons of exploration in Canada. The object of the whole exploration exercise is to Find economic deposits, once they are found, one cannot really move them elsewhere to mine them. It follows, therefore, that we should really be speaking about the pros and cons of mining In Canada and my treatise will eventually lean in this direction. In any event and before getting down to the pros and cons, let us take a quick look at the history of mineral resource development in our country since the end of world war II. At that time, we were producing well under one billion dollars worth of mineral products including hydrocarbons.

Jan 1, 1976

By K. E. Laughery

The Nevada Barite industry has experienced a 277% growth over the last five years with a total production of 2,542,000 tons. Total production prior to 1970 approximates 2,700,000 tons dating back to 1907 Annual production, as can be seen in Table 1, has increased from 192,000 tons in 1971 to 723,000 tons in 1975. During this same period U.S production has increased from 825,000 tons to 1,056,000 tons. Nevada is now the leading producer with 69% of the market. The increase in the Nevada barite production is, of course, directly related to the increased demand for weight material coupled with the lack of other sources and the relative economic advantage of the Nevada barite, A significant tonnage of Nevada barite is utilized in the non-oil well market, principally at FMC's barite chemical plant at Modesto, California; however the growth has been in the oil well market.

Jan 1, 1976

By William E. Saegart

Copper has been mined in the Philippines since at least as early as the Ming dynasty (1368 A.D. to 1644 A. D.). The principal source areas of this early production were in Camarines Norte (Paracale), in the Mountain Province, which now boasts the largest number of Philippine porphyry copper deposits, in Masbate and in Surigao, The Spanish Era began in 1521. Although they were primarily interested in gold, the Spaniards operated several copper mines including the San Remigio mine on Panay and the Lepanto mine in northern Luzon, beginning in 1842 and 1865 respectively. Prior to World War II most of the Philippine copper production was supplied by these same two mines together with the Hixbar mine, Rapu Rapu Island which began operation in 1939. The Hixbar and San Remigio mines are cupriferous pyrite deposits and the Lepanto is a vein-¬form replacement deposit (Kinkel et al. ,I 1956). No significant copper production was derived from porphyry copper occurrences prior to world War II.

Jan 1, 1976

By Donald M. Ulbrich

Any of you who served in the military remember the admoniton to "get the lead out," In the military environment, where cost wasn't always a factor, "get the lead out" was more often a call for activity of any sort than activity of a particularly productive nature. As a result, when the top sergeant yelled "get the lead out," lots of people started moving.. . usually to get out of his way. Now there's a new cry, ..one that comes not only from the military but from an entire nation threatened with dependence on foreign sources for its energy needs. That cry ...get the coal out, Like the earlier order, it's a call to activity. A signal that the coal reserves of the United States must be tapped so that Project Independence can succeed by 1985, But it's more than a mere call to activity; it's also a call to achieve productivity. ,a call to produce coal both efficiently and acceptably. And that leads us to the key questions of where the coal is going to come from to meet that 1985 goal, and how can it best be mined. Where will the coal come from? There's no doubt much of it must come from surface mining in the West. How can this coal be mined? There are several options available but there is an excellent case to be made for using mining shovels and haul trucks due to their versatility in stripping, loading and reclamation, We'll explore this approach in this talk today.

Jan 1, 1976

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By Henry S. Brown

At least two dozen massive sulfide deposits in the southern Appalachians have supported significant mining operations. Literally hundreds more deposits are known to exist, but are too small to be of commercial interest. Essentially all that are being, or have been, mined are those deposits that were exposed at the surface when first discovered. It is reasonable to assume that many more massive sulfide deposits, large and small, exist hidden not far beneath the surface. The ideas I am sharing with you here today are based both on my personal studies of some of the deposits and on descriptions of deposits in the literature. An attempt will be made to account for the genetic interpretation problems raised by many of these deposits posessing both "syngenetic" and "epigenetic" features. In addition, an examination will be made of the possible relationships between the massive and the not-so-massive sulfide deposits in this region. Hopefully, these observations added to those of others will eventually lead to the synthesis of a better model on which we can base exploration programs in the southern Appalachians.

Jan 1, 1976

By Thomas J. Neil, O&apos

Mine land reclamation is a comparatively new science-Although some mining companies point with pride to reclamation efforts of 20 to 30 years ago these were the exception rather than the rule. In the last ten years the skyrocket of environmental awareness has been awesome to behold. Future shock gripped mine operators everywhere as they struggled to cope with rapidly changing and escalating demands. The initial result was that two divergent points of view became dominant. Environmentalists said, "Put it back the way it was," and the miners responded, "Let's grow some weeds and hide it." These views are not surprising as they represent rather obvious alternative responses, albeit at opposite ends of the decision spectrum. The former case has prevailed more often than the latter, as most state and federal legislation -- both proposed and passed -- has required drastic alteration of the post-mining landscape so that evidence of prior mining is largely obliterated. An exception to this has been in porphyry copper country where the infrequent abandonment of mines has given emphasis to the second philosophy -establishing vegetative cover on mine waste materials. Now, it should come as no revelation to most mining people that both of these approaches to mine reclamation suffer from serious drawbacks when applied to open pit copper mines. First, whereas waste dumps and tailings dams can be vegetated with some aesthetic benefit, the massive presence of copper mining operations remains very prominent. It is difficult to conceal an open pit copper mine. Second, returning open pit copper mines lands to their original topography and productivity is simply not a reasonable alternative.

Jan 1, 1976

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By J. D. Pitts

The worldwide production of iron ores was approximately 880 million metric tons in 1975. This level is the result of an annual growth rate of nearly four percent during the period 1967 to the present. The high growth rate was particularly significant in that two relatively severe worldwide recessions occurred in 1971 and 1975. The current upturn in world economic growth will probably allow future annual iron ore production growth rates in excess of the four percent figure, and, in fact, the International Iron and Steel Institute (IISI) has predicted that a five percent rate should be realized through 1985. The IISI figures would indicate a 1.4 billion metric tons per year output by 1985 or an increase in current production levels of around 500 million metric tons per year (MMTA)1. Even the more conservative four percent growth rate prediction from historical data would provide an 2 increase over current figures of nearly 350 MA by 1985. A large portion of world iron ore production is being provided by large resource-rich countries with relatively new industrial bases. These countries are typified by heavy export of raw materials such as iron ore and ore products and a large capital investment in the facilities to recover these raw materials. Brazil and Australia are typical of such countries and, indeed, their production of iron ore in the period 1967 to 1973 increased at annual rates of 17 to 30 percent, respectively, The continual reassessment of resources in these and other major iron ore exporting countries such as Venezuela and Liberia would indicate chat these high growth rates may continue for some years to come to meet anticipated world demand for raw steel production.

Jan 1, 1976

After the war that was nearing an end In early 1945, regular consulting work for Bralorne, the Bradleys, Pennsalt Chemical Co., and a directorship and occasional consulting for Homestake Mining Co. made it almost certain that in spite of my 61 years I would have enough work to feed my family. But this routine work would not provide enough income to lay up funds for the inevitable future when I could no longer do arduous work. And it would not give me the adventure that had first lured me into mining. Therefore I was greatly relieved as well as pleased when, in the 18 months from April 1945 to November 1946, I was asked to make three of the most adventurous as well as profitable examinations that ever came my way. Pati[n]o Mines, Bolivia The first of the exciting jobs was an examination of the Pati[n]o tin mines in Bolivia. After I had unsuccessfully tried to induce Anaconda to purchase these mines In 1915, the World War I crisis that had forced the half-Indian accountant to try to sell the mines had come to an end. The European market for tin improved dramatically, and "Don Simon" was able to borrow money for expenses while the concentrates were still In Bolivia. He took advantage of the favorable conditions by buying adjacent properties and increasing development work until his Bolivian tin mines were the greatest in the world. And his daughter had marled the French Count de Boisrouvain and was cutting a swath In high International society. Pati[n]o wanted to get rid of the drudgery of running a complicated mining Industry in a remote area In Bolivia when the fleshpots of Paris were much more seductive. An added incentive was the fact that his miners had become unruly and had even threatened his 11fe.

Jan 1, 1976

By M. Saidman, R. Pizzuti, R. Hirschfeld, A. J. Desai, J. Rand

Two bedrock tunnels, 170 to 250 feet deep and with a length of about 17,000 feet each, will be used to convey cooling water from the Atlantic Ocean to the Seabrook, N.H., Nuclear Power Plant. Seismic reflection and refraction surveys were used to obtain preliminary information about overburden and bedrock conditions. A major boring program, including core orientation and water-pressure testing, was undertaken to provide detailed geologic data. The results of the geotechnical investigation were summarized in terms of rock type, frequency and character of joints, degree of weathering, modified core recovery (RQD), pressure-test results and strength and hardness. These parameters were used as a basis for evaluating the feasibility of using a tunnel-boring machine, for designing and estimating the initial support systems, and for evaluating the grouting and tunnel lining requirements.

Jan 1, 1976

By Alfred C. Maevis

On October 27, 1972, ground was broken for the first section of the Second Avenue Subway, a two track underground rail system that was to extend from the south end of Manhattan at Broad Street, north to the Harlem River at 126th Street, a distance of eight miles. This ground breaking was the culmination of 67 years of planning for an east side subway in Manhattan. Following the successful opening of New York City's first subway on October 1904 there was a mass planning for additional subways throughout the City. In 1905 approval was requested of the Board of Estimate for a First Avenue route and Third Avenue route. The Third Avenue route was approved but when action was not taken to start construction, the approval in accordance with the conditions under which it was given was withdrawn. Further reports and plans for an east side subway, usually to be constructed on Third Avenue, were issued in 1920, in 1922, in 1924, etc. Those of us who had worked on the Sixth and Eighth Avenue subways in the thirites and early forties left to join the armed services of World War II in the expectation that we would return and start work on designing and constructing that east side subway. The reason that much of the thrust in those years was to construct on Third Avenue was that there was a Third Avenue "EL" and business interests of the City were in favor of its demolition. This demolition was accomplished in 1955 so one of the incentives to construct on Third Avenue was removed; but an east side subway was always part of the master plan of the City.

Jan 1, 1976

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By J. A. Bowersmith

The environment in which the surface mining industry operates today is considerably different than that of a few years ago. Increased pressure from the public, government, labor and internal industry factors calling for the fulfillment of rapidly changing expectations is especially intense in the surface coal mining industry. Such things as requirements for increased production, the Mine Health and Safety Act, environmental concerns and land reclamation, shortages of qualified and enthusiastic employees and market cycles coupled with price competition are but some of the specific items that are requiring the surface mining industry to better utilize equipment, materials, and labor resources available, There is one technical tool available which will assist management to increase productivity, improve cost control and assist in planning, organizing and operating surface mines. Industrial Engineering is that tool. Before a discussion of specific applications of Industrial Engineering to surface mining is conducted, it is worthwhile to review a definition of Industrial Engineering and the history of its development. The following definition has been adopted by the American Institute of Industrial Engineers: "Industrial Engineering is concerned with the design, improvement and installation of integrated systems of men, materials and equipment. It draws upon specialized know- ledge and skill in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict and evaluate the results to be obtained from such systems."

Jan 1, 1976

By George H. Tousley

As a member of the vast fraternity of those that supply and service the mining industry, I can assure you that we are amused, amazed, and horrified at the poor drilling and blasting practices of a great number of operations. Yes, ?horrified?. After all, that is our product you are using and abusing. We all know that drilling and blasting is expensive. In some operations D & B costs may exceed excavating or hauling costs, or both. At any rate, it is the only portion of the whole operation that could be said to directly affect other costs. There is no argument that it affects excavating costs. If the overburden and/or product is drilled and hauled, it affects haulage costs. It can easily affect milling costs, if more or less fines is important. And poor fragmentation affects crushing costs. If scalping is done ahead of the primary crusher it can affect production. As has been pointed out, the D & B operation itself is costly, and therefore should lend itself to close scrutiny. Anyone that could immediately decrease haulage costs by 10% would be a hero with any mining company.

Jan 1, 1976

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976