Search Documents

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The phosphorus journey begins with the extraction of primary phosphorus in the form of phosphate in apatite through openpit mining and, in some rare cases, underground mining methods. The ores are processed in beneficiation plants to remove impurities before the phosphate rock concentrate is either sold on the open market or converted into phosphoric acid in downstream chemical production facilities by the wet acid process or thermal phosphorus routes. These can in turn be converted into fertilizers, as well as used in the food and electronic industries. The advent of the EV battery has given rise to a new use for purified phosphoric acid in the production of lithium ferro phosphorus (LFP) cathode material for EV battery cathode assemblies. The production of LFP relies on raw materials such as lithium carbonate, lithium hydroxides, iron salts and purified phosphoric acid.

Feb 1, 2024

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities, and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72 × 10 m3/s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97 × 10 m3/s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16 × 10 m3/s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07 × 10 m3/s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 1, 2024

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

In mining, which is one of the industries with the highest risk of occupational accidents, a primary goal is to enhance safety through the thorough investigation of accidents using reliable methodologies. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analyzed and compared using the life-table and Kaplan-Meier methods. Accident records were classified and analyzed into four categories: environment-related, equipment-related, person-related and other accidents. Findings in terms of survival time indicate that environmentrelated and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as one year after starting work, it is recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it is determined that increasing the use of automation and mechanization in underground coal mines, combined with developing a thorough equipment safety training program to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Feb 1, 2024

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By Karl Ingmarsson

Larger mines spend millions of dollars annually on rock drilling tools, but often purchase based on historic consumption. The results vary from excess inventory to acute tools shortages. These lead to emergency sourcing, sometimes mixing products that don’t perform optimally. Boart Longyear analyzed the usage pattern of 96 thousand drill bits at thirteen different underground mining contracts, showing very high variability. The monthly standard deviation on a product level was 42%, with the highest for development and low volume bits. A new rule of thumb is suggested to carry only one month of safety stock for high volume bits, but increase to three months for low volume bits. This balance will reduce the risk of outages with less inventory. The accuracy can be improved by considering the specific conditions at each mine and reclassifying individual bits for a different safety stock level. Root cause analysis and collaborative forecasting between mines and suppliers can lead to further optimization of availability and inventory levels.

Feb 1, 2024

By Alexander Darío Huamán Ccorahua, Cayo Fernando Soto Buendía, Jhonatan Raphael Rojas Ventura

Lithium is a top-quality mineral in the energy market, with growing demand. It has many applications in medical, nuclear, and energy industries. The purpose of this article is to quantify and analyze the economic potential and projected global demand for lithium annually. It aims to determine Peru’s (specifically Puno) positioning in the global context in 2025 and 2030. The article also seeks to identify the main regulatory, environmental, and social challenges to sustainably exploit lithium in Peru. The study employs applied research (mixed approach), descriptive-correlational scope, and observational, crosssectional design. The methodology demonstrates the use of statistical techniques to model and make predictions about this energy-transition metal. Academic sources were reviewed to enable a comparative approach and projection into the future of lithium for development in the mining industry. In the last 10 years, lithium demand has grown, noting a 600% increase in the economy and projected annual growth of +26%. Exponential growth in resources is projected, where econometric, R-multivariable and R-linear models estimate that Peru could supply 1.5% in 2025 and 3% in 2030 of global lithium. Estimated growth of 5–15% in socio-environmental conflicts is projected with the start of lithium exploitation (Peru – Puno). The global potential of lithium demonstrates exponential growth. Lithium reserves in Puno - Peru would rank 13th between 2025 and 2030. It is necessary to establish a clear regulatory framework to avoid excessive increase in socio-environmental conflicts.

Feb 1, 2024

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

By Jeff Easton, J Johnson, D. Foot

The Mina Santa Rosa mine in Panama was the victim of a mine closure 24 years ago that left the community in dire straits. The mine showed the potential resources of greater than 1M ounces of gold and 4.5M ounces of silver. Veragold Mining Company decided to reopen the mine and address all the issues that were involved in the startup of an historic mine. This paper provides methods to restore the community trust, provide a transparent process, and develop an environmentally sound flowsheet. Immense scrutiny surrounded the Tailings Storage Facility, and the company developed a plan focused on paste thickening and surface stacking to eliminate the need for a conventional tailings’ facility. Paste thickener principles and benefits are also provided.

Feb 1, 2024

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By Marlies Grimmer, Frank Amo Boateng

One of the challenges of mining is the concentration of heavy metals it releases into the environment through a phenomenon called Acid Mine Drainage. Freiberg is no exception due to its long mining activities. The European Union proposes that all rivers and streams must be in a good ecological status by the year 2027 but this would be difficult for large water sources as it would be economically unviable. Consequently, the approach of treating these waters at point sources would be of immense help and hence this column experiment on mine water treatment with carbon sorbents to remove zinc form the Rothschönberger Stolln. For this experiment three resins namely, APTsorb, activated coke, charred fermentation residues (which was produced by the Freiberg University of Mining and Technology) were analyzed through a simple column experiment to determine their sorption capacities. Through their sorption capacity as this experiment seeks to ascertain: we are able to make suggestions scientifically on the best material among the three for the future design of a treatment plant for the RSS. After the experiment whereby a 10 ml peri glass column was used, material A: APTsorb showed the least adsorption capacity (0.01 meq/g) and this could be attributed to the fact that the resin works well under pre-determined parameters such as pH and surface area. Material B: Activated coke showed a better sorption capacity (0.53 meq/g) in comparison to the basis value used for this experiment. Material C: charred fermentation residue which was produced by the University showed the most efficient capacity of (1.69 meq/g). This in comparison with the value used as the basis for this experiment showed that material C (charred fermentation residue) is very efficient for zinc sorption. pH values measured at the effluent of all the experiment were slightly higher than the pH measured in the initiating water.

Feb 1, 2024

By Justine Ealy, Daniel Yang, Christina Foster

Maintaining stable high walls can be a challenging task. Complex geological and structural features, alteration zones, rock mass properties, and hydrogeological conditions must be well understood to design a safe mining environment. Economic considerations must also be taken into account as the mine operator must provide ore deliveries and protect reserves. However, even when good engineering practices are followed, and proper blasting and mining techniques are implemented, slope movements may still occur. When these slope instabilities are minor, the mine is often able to continue operations with minimal impacts on safety or production. When these occurrences are excessive and coupled with high rates of movement, a robust monitoring system is crucial to continuing mining activities while protecting personnel. This paper summarizes the approach an open pit mine in Nevada took as excessive and rapid high-wall movement was experienced in an integral area. Creative mining approaches, combined with slope monitoring radar technology, were utilized to maintain safe and successful mining activities despite active movement that exceeded an average velocity of 30 inches per day.

Feb 1, 2024

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo

Tellurium (Te), a critical mineral for solar energy technologies, faces supply risk challenges that drive the development of diversified and robust production routes. This research focused on improving Te enrichment from copper tailings (CT) produced from copper porphyry (CP) ores processing, addressing the loss of ~90% of Te minerals to tailings in the flotation process of CP ores. Gravity separation and froth flotation processes were used as possible enrichment routes of Te-bearing minerals (i.e., pyrite) in CT. In the froth flotation process, synergistic combinations of reagents were tested to achieve an acceptable enrichment ratio of Te minerals. Comprehensive characterization analyses showed significant Te enrichment in the flotation concentrates. Tellurium was recovered at 90%, while the grade of Te in the concentrates was 1.4 ppm using a xanthate collector and glycol frother compared to <0.5 ppm in the flotation feed. Findings showed that Te-minerals’ enrichment was also feasible in CT using the proposed combined concentrations routes (i.e., gravity separation followed by froth flotation) by looking at Fe, Cu, and S enrichment. This study also highlighted the importance of understanding the deportment of Te minerals in different process streams to develop and optimize efficient enrichment practices.

Feb 1, 2024