Search Documents

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By K. L. Kasperski, M. T. Ityokumbul

The effect of reaction conditions on the desulfurization of oil-sand coke residues was studied. The variables investigated were temperature, reaction time, heat transfer resistance and mode of caustic soda addition. The results show that oil-sand coke desulfurization increases with temperature, reaction time and heat-transfer rate. In an oxidative environment, coke combustion during molten-caustic leaching (MCL) commences at temperatures above 500 °C. The mode of caustic addition has no effect on coke desulfurization.

Jan 1, 1996

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine&apos;s collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine&apos;s cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By Nina I. Fedunec, Olga E. Fomicheva

Results of researches on creation of the intelligent adviser system for mining dispatcher are represented. A method of the analysis of subject domain is considered and results as the generalized expert questionnaire and diagrams are represented. The system-adviser REALTREE, functioning in real time, is represented, results of an estimation of a system effectiveness during decision making by the dispatcher are submitted.

Jan 1, 1996

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By A. W. Khair, J. A. Organiscak, M. Ahmad

This paper describes research that seas conducted on bit wear and respirable-dust generation. The investigation was performed by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy and dust of one type of conical bit cutting coal. The objective of the USBM study was to identify qualitative bit-selection guidelines. The objective of WVU&apos;s research was to determine optimum bit-replacement guidelines. Both research studies found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1996

By C. Bazin, B. Girard

The application of time series analysis techniques to plant data provides a method for examining and modeling the behavior of operators during the operation of furnaces for the reduction of ilmenite concentrate. The obtained model is used to assess the consistency of actions carried out by the operators and to review and improve the training procedures.

Jan 1, 1996

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By Timothy D. Arnold

Barrick Gold’s Bullfrog underground mine, near Beatty, NV, was established as an after-thought to the main open pit. As open pit ore dwindles, the underground mining became increasingly more important as an ore source, and to the overall economics of the project. This situation is similar to many other mines. Today, there is a move towards underground mining in the United States. There are inherent problems in starting and operating underground mines in the shadow of any open-pit operation. Several attempts were made at the Bullfrog Mine for productive increases. Some were successful, while others were not.

Jan 1, 1996

By W. X. Wang

In the mining and quarry industries, rock fragments are often transported by conveyor belt. To estimate the qualities of the rock fragments (i.e., size distribution and shape), an operator must take samples from the conveyor and manually perform a sieve analysis, which is time-consuming and tedious. Alternatively, an image-analysis system can be used to monitor the fragment quality on a fast moving conveyor belt. However, images of fragments on a fast moving belt vary to such a degree that the quality of any two successive images are not the same, and some of the images are of such poor quality that they are unrecognizable by human eyes. If poor-quality images are directly analyzed by a segmentation algorithm, the analysis will not be satisfactory. To resolve this problem, it is necessary to use an image-classification pro-gram for the automatic selection of fragment images with good quality. Because of this need, an image-classification program was developed and tested both in the laboratory and in the field. Testing of the system on different types of fragments showed that the system works reasonably well.

Jan 1, 1996

By James P. Cooney

What is required for the mining industry to grow and prosper in a politically challenging world? The answer to this can be summarized as “the industry’s three priorities.” The first priority is gaining access to the world’s mineralized jurisdictions. The second is establishing a measure of security and predictability in government treatment of mining. Confidence in the stability of the fiscal and legal framework within which mining operates is necessary to encourage the investment of large amounts of capital in mine development. The third priority is sustaining the industry’s welcome during the long term in those jurisdictions worthy of investment.

Jan 1, 1996

By Alan A. Campoli

The US Bureau of Mines (USBM) conducted research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments. The goal is to minimize the over and under design of mine roof support, resulting in more productive and safer mines. To obtain the necessary data on roof behavior and support performance, USBM conducted several field studies. Each study covers roof geology, stress regime, ground reaction, support interaction and mining environment. A consistent experimental design is being used. This includes measurements of roof bolt loads and roof movements. So far, 10 studies have been conducted in several geologic settings.

Jan 1, 1996