Search Documents

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By C. G. Anderson

Historically, the treatment of orebodies for recovery of valuable constituents presents many processing challenges. In a time of heightened environmental awareness, the constraints placed on processing complex orebodies are becoming more and more pronounced. As such, established technologies are limited in their ability to fill the needs of these emerging sources of raw materials. A prime example of this is in processing PGMs from primary sources. Normally, this type of material is found in a nickel-copper-iron sulfide matrix. Typically, these materials are processed by established pyrometallurgical means. However, other options should be considered. Hydrometallurgical processes are available which offer advantages over pyrometallurgical methods. One of these is the nitrogen species catalyzed sulfuric acid pressure leach used industrially by Sunshine Mining and Refining Company. In 1990, laboratory work was undertaken in cooperation with Stillwater Mining Company to test PGM matte materials from the Columbus, Montana smelter. The initial results were very positive, and they led to a design to recover PGMs in a high grade residue and to recover nickel and copper as valuable products. Handling the iron and other wastes in an environmentally safe manner was also successfully investigated.

Jan 1, 1995

By P. W. Johnson, H. Fan, S. B. Patton, T. Novak, R. L. Sanford

A computer model is presented that quantitatively uses the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasitication on the ventilation system in a longwall panel.

Jan 1, 1995

By J. M. Pugliese

The U.S. Bureau of Mines is developing designs and estimating costs for vertical in situ copper mining wells as part of its in situ mining research program. Conceptual designs and estimated costs for "deep" 1100 m (3600 ft) recovery and injection wells in an undisturbed copper ore zone are presented. Within a single in situ copper mining well, multiple perforated well completions and associated costs are discussed for two ore zones between depths of 370 m (1200 ft) and 550 m (1800 ft). The order of well specifications for designing these wells is explained.

Jan 1, 1995

By M. S. Celik

Salt-type minerals are usually floated with anionic and cationic collectors. Flotation of a number of systems has been reported to remarkably increase above the concentrations where surface precipitation of collector-metal salt is initiated. Some studies attribute this phenomenon to heterocoagulation of oppositely charged collector colloid and mineral particles. In this study, examples are given on boron minerals to demonstrate that the high flotation region occurs when particles, colloidal precipitates and bubbles acquire a similar charge which induces Van der Waals interactions resulting in hydrophobic bonding.

Jan 1, 1995

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operating point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique features of the Lone Tree sulfide deposit and its amenability to low-temperature oxidation. Problems encountered during pilot plant operation and their solutions are discussed.

Jan 1, 1995

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By J. Kallioinen

Theoretical considerations, experimental results and plant experience have lead to a new design concept called the unit reactor approach. It has been successfully implemented to the largest flotation cell on the market, the 4000 cu ft OK TankCell. The work has also lead to a new operating idea called size specific flotation. The paper discusses these concepts in the view of full scale field experiments. In large scale porphyry copper flotation experiments conducted in Chile the new large TankCell with its new low energy input Free Flow mechanism out-performed the more conventional designs. The recovery was substantially better, especially in the coarse fractions. In some experiments the difference in total recovery was up to 10%-units and the savings in total energy consumption at the same time over 40%.

Jan 1, 1995

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By J. Kallioinen

The development of mechanical flotation cells has resulted in larger and better cells. This has led to flotation banks with only a few units, even in large-scale operations. This equipment development makes the old operational considerations ineffective. The flotation cell must be considered as a single reactor unit capable of handling specific tasks and getting excellent metallurgical performance. The result of the unit reactor concept development was the new large TankCell that comes in sizes up to 113 m3 (4,000 cu ft). The TankCell construction includes new modified rotor-stator designs, new tank geometries and a froth-handling capability independent from subprocesses taking place in the pulp (i.e., air addition). The conventional idea of a single flotation cell type for fine, intermediate and coarse materials does not give optimal results. Optimal flotation of coarse and fine particles needs different mechanism designs, impeller tip speeds and different froth control objectives.

Jan 1, 1995

By Robert W. Bartlett

Pretreatment of sulfidic refractory gold ore by biooxidation in coarse-crushed ore heaps is a promising new technology, especially for low-grade ores that cannot afford pressure leaching or roasting. An algebraic equation for determining the economically optimum biooxidation of the sulfide minerals in the ore is provided that is based on the empirical biooxidation rate constant for the ore, the project's financial discount rate, the ore grades of both refractory and non-refractory gold, and the gold price. Then, the economically optimum duration of bioheap pretreatment, t$, is determined from its logarithmic relation to the optimum fractional extent of ore biooxidation, F$, through the ore's biooxidation rate constant. In doing so, it is assumed that the ore is adequately crushed and amenable to bioheap pretreatment and that the cumulative oxidation of the ore with time is known from ore testing so that the rate constant can be determined.

Jan 1, 1995

By C. DeW. Van Siclen

A simple mathematical description of the settling behavior of monosized particle suspensions is derived by consideration of the physical processes involved, and applied to data recently published in this journal.

Jan 1, 1995

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By I. K. Gilmore

PCS Phosphate operates an open-pit phosphate mine in the central coastal plane of North Carolina. The company has mining and refining facilities located on the south shore of the Pamlico River. Phosphate ore is recovered at the Aurora facility by open-cast mining techniques. Walking draglines and bucketwheel excavators remove the overburden and mine the phosphate ore. The mined ore is slurried about 8 km (5 miles) to the processing plant. At the plant, the phosphate ore slurry is passed through screens to remove material coarser than 2 mm (10 mesh) and then pumped through hydrocyclones to remove material finer than 75 mm (200 mesh). The resulting phosphate and sand mixture is treated with various reagents and subjected to an anionic flotation process. A cationic flotation process removes the sand from the final phosphate concentrate.

Jan 1, 1995

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By Lynn B. Hales, Randy A. Ynchausti, Robert W. Colby

Process control systems have evolved from single loop control to distributed control with computer based expert control strategies. The next step is to add adaptive control to the expert control strategies. An object-oriented intelligent adaptive optimization approach is defined and simulated results are presented.

Jan 1, 1995