Search Documents

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Gary A. Perry

Cyprus Sierrita produces copper and molybdenum from its Sierrita and Twin Buttes open pit mines south of Tucson, AZ. Both pits were started in the late 1960s and are more than 460 m (1500 ft) deep. Sierrita has used a Caterpillar 992C Remote Controlled Loader since January 1993. The loader was justified to increase safety and profits at Sierrita. It has exceeded all expectations. As of June 1993, the 992C had produced additional profits of more than $1.5 million. Safety and Geotechnical The safety of Cyprus personnel and equipment is always of prime concern. The remote controlled loader removes personnel from the active raveling area. But it requires prudent operation. The remote controlled loader discussed here is always intended to be used in a safe manner under a managed slope. Any increase in slope angle or use of any equipment under a critical slope is taken only after careful analysis of the specific

Jan 1, 1994

By Patrick J. Coughlin

Shortly after Asarco Inc. purchased the Ray Mines Division from Kennecott in 1986, the company began an expansion program to increase copper production. The Bechtel Corp. oversaw engineering procurement and construction management for a new in-pit crusher, overland conveyor system and concentrator facility. Construction started in May 1990 on these facets of the expansion project. The concentrator was commissioned in February 1992. The Ray concentrator uses a single-line, semiautogenous grinding circuit (SAG) with a design through¬put of 27 kt/d (30,000 stpd). In the early 1960s, Kennecott conducted pilot plant grind tests of Ray mine ores to determine their amenability to SAG and autogenous grinding methods. Those tests, though, were not followed up. During 1973 and 1982, Kennecott conducted additional pilot testing on some of the softer ore types. In 1989, Asarco ran a final series of SAG pilot grinding tests at Lakefield Research, which became the basis of the new Ray concentrator grinding circuit. Even though pilot test work demonstrated that some of the Ray ores gave satisfactory results during the autogenous grinding tests, the SAG option was selected for the primary comminution device. Due to the wide range of mineralogies encountered in the Ray ore body, selective mining and blending of these ores would be required to achieve the necessary production efficiencies and throughput rates using an autogenous grinding circuit.

Jan 1, 1994

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By D. Eyde

The zeolites review arrived too late for the June issue. The natural zeolite industry continues to grow even as some companies look for the exits. Production for 1993 was estimated at between 42 and 44 kt (46,000 and 48,000 st). That is between 7 and 9 kt (7700 and 9900 st) above 1992 production. GSA Resources, Saint Cloud Mining, Steelhead Specialty Minerals, Teague Minerals, UOP and Zeotech all reported continued growth last year. At the same time the East-West Minerals' Eastgate mordenite mine, and American Resources' Ash Meadows clinoptilolite operations both shut down their processing plants and are attempting to sell the mines and facilities. In addition, Tenneco Minerals continued its attempt to sell the Mud Hills clinoptilolite deposit. Unimin entered the natural zeolite industry through its acquisition of several properties of Aimcor. The properties included the Ben-Jel bentonite and Castle Creek clinoptilolite deposits and processing facilities near Caldwell, ID

Jan 1, 1994

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

By Peter W. Harben

Once considered the dowdy country cousins of the glamorous metallics, industrial minerals are shedding their old image. They are neither common nor easy and their time has come in an age of increasing specialization. Consider that of the 45 or so industrial minerals and rocks listed in [Table 1], almost three-quarters have ten or fewer significant suppliers (i.e., those individual countries contributing 2% or more of total world production); in more than half the cases, 85% of world production is accounted for by only five countries or fewer. Curiously, even materials that appear to be virtually ubiquitous like crushed rock and common salt have significant production vacuums. For example, there is a severe lack of sound aggregates along the US Gulf Coast and common salt production on a large scale is virtually absent in central Africa. These examples all underline the obvious, but acute truism that "The single most important fact about mineral resources is that they are not distributed equally over the world" (Flawn, 1966). Just as significant today is that human resources are not distributed equally over the world, and so arise some interesting commercial incongruities. In certain regions raw materials are plentiful but consumers are not, and without a market a mineral deposit is merely a geological curiosity. Elsewhere, there may be a market but no local raw material supply. For example, despite a huge market there is no or virtually no commercial production of chromite, diamonds, and manganese in the United States and Canada, nor phosphate rock, diamonds, rutile, and zirconium minerals in western Europe. In contrast, Australia with its small domestic market is the world's largest supplier of bauxite, diamonds, ilmenite, natural and synthetic rutile, and zircon; the same is true for South Africa which is a leading producer of chromite, manganese, diamonds, andalusite, ilmenite, rutile, and zircon (Table 2). In the commercial world, Nature's uneven distribution is counterbalanced by deep sea international trade.

Jan 1, 1994

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By J. A. Lombardi

Innovative hard rock narrow-vein, longwall, and stope leach mining systems concepts are described and evaluated economically. The principal tool proposed for use in these systems for both mine development and production is the U.S. Bureau of Mines radial-axial splitter. The mining systems concepts are prefeasibility level costed and projected to be cost competitive for steeply dipping veins, 0.6-1.2 m wide, for horizontal tabular ores 2 m -5 m thick, and for leachable ores with greater than a 1.7:1 stripping ratio. In all of the systems the orebody, less swell, is retained underground for use as backfill.

Jan 1, 1994

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By Ralph A. MacMillan

Electronic systems introduced for haulage equipment in recent years probably exceed what mine management is prepared to use. Haulpak trucks alone are equipped with General Electric's Statex III drive system controls, Detroit Diesel's DDEC, Cummins' Centry engine management system and the Haulpak Management System (HMS). The future holds promising developments of even more sophisticated electronics that will lead to unmanned truck operation and control. Trolley-assist will finally come into its own due to the importance of environmental issues, as well as the high potential for increased productivity with dramatically lowerfuel consumption. All of these high technology systems do not mean much unless they add value to mining operations. Some of the benefits that can be expected from these systems are reviewed. In the near future, haul truck control and monitoring systems will be fully linked by telemetry to a mine's dispatch system, as well as to its maintenance management information system. The manufacturer and distributor can also be kept in the communications loop, so that they can better serve customer needs. Portable computers will allow technicians to talk to machine systems to quickly locate a problem, look up service information, check what parts are required and electronically order them.

Jan 1, 1994

By Kenneth A. Gutschick, Harry L. Francis

A large number of minerals and chemicals (Table 1), some mineral-derived, are used in the treatment of both potable water and domestic sewage waste water and solids (Anon., 1990). In water treatment there are ten principal process uses as shown in Table 2 (Anon., 1990), which also lists the major chemicals in each process. Since lime (calcium oxide, calcium hydroxide, and dolomitic lime) is the largest chemical (by tonnage) used in water treatment, this chapter will deal primarily with this product. Note that it is included in five of the process uses shown in Table 2, and that indirectly it is also used in at least one other category (taste and odor control, where lime is used with potassium permanganate to provide optimum pH condition). POTABLE WATER TREATMENT Water Softening The biggest use for lime in water treatment involves water softening, where it serves to reduce carbonate hardness caused by dissolved bicarbonate and carbonate compounds. Currently there are more than 1000 domestic water softening plants (Table 3) located in most sections of the country, but particularly in Ohio, other midwestern states, Florida, and Texas, where limestone bedrock abounds (Anon., 1990). Among the other uses for lime in water treatment are coagulation, disinfection, and removal of heavy metals due to high pH softening, removal of certain radioactive and organic compounds and fluorides, neutralization of acidic water, removal of silica, particularly with dolomitic lime, and removal of color. Most of the above advantages accompany water softening, although at some plants lime is used specifically for one purpose, such as silica removal with dolomitic lime, minimizing pipeline corrosion by addition of lime to correct an aggressive water, and others. Hardness in water comprises two types - carbonate hardness, caused by dissolved calcium and magnesium carbonates and bi- carbonates, and non-carbonate hardness caused by dissolved non- carbonate salts, particularly calcium sulfate, calcium chloride, magnesium sulfate, and magnesium chloride. Total hardness is the sum of the carbonate hardness and non-carbonate hardness. Waters are classified as soft (0 to 75 mg/L as CaCO,), moderate (75 to 150 mg/L), hard (150 to 300 mg/L), and very hard (above 300 mg/L). Most water plants strive to reduce total hardness to about 100 mg/L, although in recent years the tendency in some cities has been to allow a little higher value in order to reduce both chemical costs and the amount of water softening sludges produced. There are four basic types of softening plants: lime softening, primarily to reduce carbonate hardness; lime-soda softening, for reduction of both types of hardness (in some plants caustic soda is used in place of soda ash, but it is more costly); split lime-zeolite, where a base exchange mineral is employed in place of soda ash (this system also requires salt [sodium chloride] to regenerate the zeolite mineral); and finally zeolite softening, which is generally used in small systems for private houses and small municipalities. Principal disadvantages of the latter system are its relatively high cost and the salt requirement, which introduces considerable quantities of soluble salts into the waste water discharge system.

Jan 1, 1994

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By D. M. Neil

Road-headers are one of the most popular mechanized excavators used in mining and civil under-ground construction. These machines are primarily used in soft to medium hard rocks. This paper reviews the parameters associated with the application and operation of road-headers and presents a method for estimating cutting performance.

Jan 1, 1994