Search Documents

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By J. M. Manka

American mining companies operate many drum hoists, hoisting from varying depths with varying payloads. This paper reviews the procedure for selecting optimum wire rope constructions for existing hoisting installations. Selection for proposed installations, along with recommended hoisting parameters, is also discussed. To achieve optimum rope performance, preventive and corrective maintenance procedures are required and are reviewed here, along with examples of rope problems and their causes.

Jan 1, 1993

By O. Ofor

Finely-ground hematitic ore, too high in silica (quartz) to be commercially viable, was treated by emulsion flotation. A three-component emulsion mixture was used at temperatures ranging from ambient (22° C) to 30° C, 40° C, 49 °C, 59° C and 68° C. The optimal emulsion dosage and composition at ambient temperature were used to determine that dosage for higher-temperature flotation tests. The crushed ore (100%, -8 mesh) was repeatedly washed with tap water, and the filtrate's ionic content was analyzed. The separation efficiency values (a measure of the selective separation and concentration of hematite from gangue minerals) demonstrated temperature dependence, with marked increases at temperatures above ambient. The optimal separation efficiency occurred within the range from 30° C to 60° C. The improved separation efficiencies at temperatures exceeding ambient are explained by quartz depression. This depression is attributed to: • the precipitation of quartz-activating cations, principally calcium and magnesium, at increasing temperature; and • temperature's effect on the collector's solubility and attachment to the aqueous hematite surface.

Jan 1, 1993

By Leonard Harris

Mining is a business and, therefore, is expected to make profit for its investors, like any other business. It is a risky business which requires the expertise of professionals from several disciplines to make it successful in the finding, evaluation and development of a new mining venture. Many of the same disciplines, as well as experts in some other fields are required to operate the facilities once they are built. To manage all this, wide-ranging, versatile and sharp managerial skills are required. On the U.S. domestic front, the most important management issues requiring attention today and tomorrow are the increasing unwarranted attacks by anti-mining groups and legislators on the industry and aided by an unchallenged, but widespread, public view that mining is not necessary and damages the environment. Higher costs to mine and process deeper and more refractory ores are also of great concern. More and more attention is being focused, therefore, on overseas projects under the belief that undeveloped countries will recognize the economic value of mineral production and that lower costs can be achieved.

Jan 1, 1993

By J. E. Feddock

To succeed in today's competitive coal market, coal companies must continuously improve production and lower cost. However, the coal industry's historical management practices must change to remain viable? The practices of the current day efficient coal mine manager are reviewed and examined using W. Edwards Deming's definition of management. The statistical tools, including Pareto Charts, Control Charts and Scatter Diagrams, which identify the problems management must approach differently to increase productivity at a coal mine, are discussed.

Jan 1, 1993

By Alfredo P. Vargas

Industrial flotation of sulfide ores is 80 years old. It has gone through many advances to date. However most flotation operations are still struggling to improve performance, which as a worldwide average is at the 90% level. What can be done to push the ceiling to 95% or better without performing finer primary grind, nor without duplicating flotation plant capacity? Such "unique task" can be performed by the low volume high capacity new flotation equipment known as the JAMESON CELL, when used as, "post-scavenger" of final plant tails. Improved efficiencies are obtained mainly from two cases: -Particles which never contacted a bubble. -Particles sheared-off by cell turbulence due to reduced number of hydrophobic sites. The application reverses conventional trend of using large volume mechanical cells by trade-in with smaller efficient equipment: resulting in reduced capital expenditures and operating costs. Outstanding "pre-rougher" applications are also presented.

Jan 1, 1993

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By Heflin. L.

The Washington Metropolitan Area Transit Authority, WMATA, has constructed over 92 revenue miles of rapid transit facilities including some 14 miles of rock tunnel and 12 miles of earth tunnel. The system map is shown in Figure 1. During construction it is not unusual for contractor to encounter ground conditions resulting in major problems and extra cost. Problems such as major rockfalls and a "stuck" boring machine in squeezing rock are not unusual. In recent years, faced with additional tunnel construction projects, the Authority has sought newer tunneling methods which might be less costly. One new method which has been tried is NATM, the New Austrian Tunnel¬ing Method. NATM, which is applicable to both soft ground, mixed face and rock tunneling, relies on miners and comparatively small machines to excavate in conventional ways, but it is unique in its methods of obtaining "stand-up" time at the excavated face and its method of using shotcrete as an initial lining, frequently with a drainage system to reduce hydro-static pressure on the final lining. Lower costs result from use of a cast-in-place concrete liner, and from a reduction in the number of work operations at the mine heading which provides better daily production. WMATA has recently completed three twin bore tunnels constructed by NATM technology. The first was the Wheaton Tunnel and Section, followed by the tail track tunnel to total some 4200 linear feet cut through jointed rock up to 270 feet below ground surface, and the last was in soft ground at Fort Totten. A

Jan 1, 1993

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By Mulong Yu, Yosry A. Attia

Beneficiation of high magnesium Florida phosphates requires ultrafine grinding to liberate the dolomite (the main source of magnesium), and a separation process capable of dealing with ultrafine sizes such as selective flocculation. The objective of this study was to investigate the feasibility of separating dolomite from apatite ultrafines by selective flocculation. To achieve this objective, selective polymeric reagents to either dolomite or apatite must be first designed and synthesized. This challenging task was accomplished by carefully selecting complexing/chelating agents which are selective to either the Ca or Mg ionic sites on the minerals, and incorporating these reagents into the structure of long chain water soluble polymers to obtain either selective flocculants (with high molecular weight, MW, polymers), or selective dispersants (with low MW polymers) to either the dolomite or the apatite particles. Synthesis and testing of these polymers on individual and mixed mineral slurries, and on a sample of natural high magnesium phosphate ore, have been attempted and the results are described in the paper. The preliminary results showed encouraging signs for the feasibility of selective flocculation separation of dolomite from apatite.

Jan 1, 1993

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By S. L. Zhu, Brij M. Moudgil, J. L. Pinault

Prompt neutron activation probe (PNAP) was evaluated to determine chemical composition of phosphate rock slurry in-situ. The technique was able to precisely analyze Ca, Si and H using a 252Cf source. Direct measurement of P and Mg was not accurate due to interference by the rare earth elements associated with the Florida Phosphate Rock. The solids loading, particle size distribution and flotation reagents present in the slurry had no significant effect on the accuracy of the measurements. The technique was found to be reliable also under industrial conditions.

Jan 1, 1993

By Herb Wilson

The Klondike symbolized one of mankind's driving forces - the desire to lay one's hands on a scarce resource, gold, in that case - and in doing so to make some money along the way. It can be argued that construction aggregates - a once lowly and ignored sector of the natural resource industries - have become the desired targets of their own "Klondike." This began in the 1970s and accelerated to a frantic pace in the 1980s. The scope of industrial minerals is very wide. It ranges from high value minerals such as talc, bentonite and kaolinite to the truly humble minerals of sands and gravels, limestones and granites. Their major end uses are in construction aggregates. A rich variety of different mineral types all make good construction aggregates. However, those successfully used have two fundamentals in common: • Their technical characteristics are appropriate for the requirements of their end use. • They are located within an economic distance from the market. The North American market This is the largest construction ag¬gregate market in the world. Consumption in 1990 reached 2.2 Gt/a(2.5 billion stpy). This rate of consumption has grown steadily over the past decades. In the United States, from 1963 to 1989, it averaged a 1.6% compound growth rate. Within this long-term trend, there are business cycles, because aggregate demand is closely linked to economic strength or weakness. The North American market also displays the greatest per capita demand for aggregates when compared to the major industrial economies (Table 1).

Jan 1, 1993

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993

By George A. Lawrence

A new super-large 100 m3 (3500 A3) pneumatic mechanical flotation cell is now available to meet future mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom cylindrical tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. This new flotation cell is powered by a custom designed hydraulic motor package that provides infinite speed control in individual cells and a soft start under load

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993