Search Documents

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By Brian Fulcher

The Fort Lawton Parallel Tunnel was built in 1990 - 1991 by Morrison Knudsen Corporation (MK) as an integral part of Seattle METRO's planned expansion of the Westpoint Treatment Plant. The project included a concrete lined 2542 m (8,340 ft) long tunnel bored in sands and clays under the presence of methane gas and over 27.4 m (90 ft) of ground water table. The tunnel roughly paral¬lels an existing and still operating 3.65 m (12 ft) diameter tunnel originally completed in 1909. The parallel tunnel was constructed using a Lovat 4.72 m (15 ft-6 in) earth pressure balanced TBM with ribs and timber lagging as primary support. The tunnel alignment crossed under as much as 91.4 m (300 ft) of overburden as well as twin mainline railway tracks; terminating in a shaft adja¬cent to the Seattle ship canal. The project was completed in June, 1991 after a final "wet-tap" tie-in to the existing brick-lined sewer; over five months ahead of the contract schedule. This paper will describe the construction methods, job site conditions and difficulties encoun¬tered on this very challenging and successful project.

Jan 1, 1993

By F. M. Doyle, Jiang Tao, Xu Shi, Chen Jin, E. Peters

Tafel curve technique and leaching tests have been applied to study the kinetics of gold leaching with thiosulfate. Results show that cupric ions and ammonia play the part of catalysts in the leaching of gold with thiosulfate. The activation energy of gold dissolution is calculated as 27.99 KJ/mol in the absence of both cupric ions and ammonia. However, the energy is reduced to 15.54 KJ/mol in a solution of 0.01 mol/L Cu (NH3)2 4* and 0. 5moVL total ammonia. The reaction order of Cu (NH,) g is one in the range of 0.001~0.1mol/L. These results support the electrochemical-catalytic mechanism pro- posed by the authors and explains the behavior of cupric ion and ammonia (Jiang Tao, et al., 1993)

Jan 1, 1993

By M. S. Riyaz Ulla

The Hutti Greenstone belt, located in the northern side of Dharwar Craton, India, contains several promising gold fields. It is predominantly composed of meta-volcanics with minor intercalations of meta-sedimentaries. Alkali-SiO2 and Zr-P2O5 diagrams, immobile element trends, and an iron-rich trend on the AFM diagram indicate that the volcanic suite is low-potassium tholeiitic basalt. The lower Mg number, MgO-TiO2, MgO-Ni, and Ni-Zr plots reveal that the basalt was derived from a fractionated, highly evolved magma generated by 10-20% melting of the mantle at 1100°C and 5 kb pressure. The chemical variations suggest that the Hutti metabasalt represents volcanic arc rocks generated at a converging plate margin.

Jan 1, 1993

By Ahmed M. Nofal

This article reviews some important characteristics of the known Egyptian phosphate deposits, such as mining conditions, transport criteria, quality of products affecting their export markets and utilisation in fertilizers industry. Special attention will be given to the newly discovered large deposit of Abu-Tartur with some billion tons of ore reserves. A big project is now under implementation on Abu-Tartur deposit where the long-wall method of underground mining will be applied and a flow sheet of beneficiation will be in operation including a particular feature nontraditional in phosphate processing: high-intensity magnetic separation to eliminate dolomite impurities. Comparison with some international phosphates will be tried in order to trace the situation of Egyptian phosphates in the world market.

Jan 1, 1993

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

By B. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the project's design and ultimate economic success. Incorrectly-determined lifetimes can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the optimal lifetime calculation using traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the project's net present value is maximized.

Jan 1, 1993

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By R. K. Mehta, K. N. Han, P. B. Queneau, V. Dieudonne

A study based on a statistically designed sets of experiments (central composite design) was conducted to determine the optimum conditions for leaching a subbituminous coal (7.0 % ash) from the middle Wyodak seam in mild sulfuric acid solutions. The statistical analysis was conducted with the ash content and ash removal as the dependent variables and with the coal loading, acid concentration, ferric ion concentration, and temperature as the independent variables. Treatment of the experimental data via a simple genetic algorithm (GA) revealed that acid concentration and temperature are the two most critical variables. Unlike the case with bituminous coal, the ferric ions addition shows no beneficial effect. The optimum "macro response" predicted by GA was verified experimentally; the ash content was reduced to 2.7%, which is close to the value predicted by GA. The ash content was further reduced to 1.7% in a two-stage leaching process devised by incorporating the optimization results with that of leaching kinetic studies.

Jan 1, 1993

By Thomas J. Martin, James W. Martin, Paul F. Martin

The conveyor belt is the basic building block of a broad range of material handling applications in modern mining systems. The mining plans and site conditions dictate basic system requirements but this is only a part of total design evaluation. The total system in the typical mining situation can encompass all the activities from the excavators at the mining face to the processing plant, site loadout facilities and/or a power plant. The number of alternative configurations which must be evaluated including subsystems and components is limited only by analytical time and creativity. The constraints and issues which must be addressed continue to expand, driven by reliability, environmental impact and cost competitiveness. All of the system requirements must be translated into specifications for costing, final design and construction.

Jan 1, 1993

By S. Pignolet-Brandom, E. Fregeau-Wu, I. Iwasaki

To recycle steelmaking slags for their iron, manganese and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote sufficient grain growth to achieve liberation. In situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate and the addition of fluorspar promoted grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modeling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1993

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Robert B. Hopler

Explosives research and development has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. Today, this process continues at an accelerated pace due to the tools presently available to the explosives and mining industries. Background Explosives have been used in coal mining since the industry's earliest days. Black powder, introduced into metal mining in 1627, undoubtedly was introduced into coal as soon as a need to replace pick work was apparent. Until the invention of the safety fuse by William Bickford in 1832, the only initiation methods available were the straw, quill and miner's squib. Disastrous explosions underground in England brought about studies on their possible causes (Atkinson, 1886). The studies showed that, while explosives contributed to the accidents, the real villain was coal dust, since that was the agent that transmitted the disaster throughout the mine workings. To improve underground safety, research was applied in an attempt to make explosives that could be safely fired in a methane air atmosphere. The Prussian government was apparently the first to establish a testing station for coal mine explosives. This occurred in 1885 (Guttmann, 1909).

Jan 1, 1993

By Andrea B. Baldwin

Solvay Minerals, Inc. (formerly Tenneco Minerals Company) is one of five producers who use trona to produce soda ash at Green River, Wyoming. Over the years, many producers, including Solvay Minerals, extended their product lines by manufacturing other sodium products based on trona. This paper focuses on the criteria used by Solvay Minerals in the selection of new products added at its Green River, WY operations. An example is given in the selection of caustic soda production.

Jan 1, 1993

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993