Search Documents

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By H. E. Bonner

The recovery of fine coal has historically had limited success due to the intimate clay association on the surfaces of the coal particles. This clay presence has detrimentally affected conventional beneficiation techniques resulting in a recovered product containing unacceptably high concentrations of ash and moisture. An ultrasonically activated tray that operates in a continuous fashion has been developed that separates the clay film from each particle's surfaces. This separation is of sufficient duration to allow conventional beneficiation techniques to be utilized more efficiently.

Jan 1, 1989

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By S. Hartman

The Escalante Silver Mine in Southwest Utah produces an average of 71.000 kg (2.3 million troy ounces) of silver dore annually. Precipitates from a cyanide leach circuit are treated by either acid leaching prior to fusion or a direct fusion with nitre. Process development, plant experience, and a comparison of both methods will be discussed. Plant experience from the custom treatment of a gold/silver precipitate containing matte producing elements will also be covered.

Jan 1, 1989

By J. H. Mackey

"Where can I obtain a reclamation bond today?" "Who is writing your bonds?" These questions are common and heard frequently. The fact that the Society of Mining Engineers has determined that two of the five environmental topics reviewed at the 1989 Annual Meeting relate to reclamation bonding indicates to me that those who are involved in the coal industry, no matter what capacity, remain very cognizant of the reclamation bonding dilemma.

Jan 1, 1989

By J. R. Parry

Over the past several years, computerized financial models have been an important part of Newmont's strategic planning process. Two applications will be discussed in this paper: a general purpose financial model of Newmont, and a detailed operational/financial model of Magma Copper Company. Newmont?s general purpose financial model was developed using Lotus 1-2-3. It was designed to aid management in assessing the financial consequences of investment and financing decisions associated with long-term strategic planning by simulating the consolidated effect from individual transactions. Not only is the model capable of assessing the sensitivity of specific decisions to changes in the external economic environment (i. e., commodity prices, interest rates, inflation and exchange rates), it can also evaluate the effect from operating and financial decisions, including changing production levels and cost structures at individual operating units as well as simulating several types of transactions, including equity and debt issues, acquisitions and divestitures. The analysis of Magma Copper Company required the development of a detailed operating and financial model of the Company. The model was developed using IFPS in the corporation?s UNISYS (then Burroughs) B7900 mainframe computer and included separate pro forma financial statements for each of San Manuel-Pinto Valley's mines and concentrators, as well as Magma's smelting and refining operations. The outcome of this analysis was the decision to merge Magma Copper and Pinto Valley Copper Corporation, and to recapitalize the new corporation in order to provide funds for a retrofit and expansion of its Arizona smelter and expansions of its refinery and SXEW facilities.

Jan 1, 1989

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By S. D. Thompson, L. Adler

J.R. Sturgul Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modern versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 12, 1988

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

BP Minerals America (BPMA) has completed its $400 million modernization of Kennecott Utah Copper's Bingham Canyon mine. Modernized facilities include the in-pit crusher, conveyor, ore storage area, concentrator, ore pipe-line, and tailings pipeline. With modernization, Kennecott will achieve substantial cost reductions. Bingham Canyon is now one of the lowest cost copper producers in the world. And the mine will continue to provide jobs and income in Utah for another 30 years or more. The Modernization Project began in February 1986. The work took 33 months. In late 1987, the construction force peaked at 1100 workers. Kennecott Utah Copper now employs a permanent work force of 2100 employees. Less equipment and more efficiency The modernization work has increased the scale of the facilities that transport and process copper ore. A large, continuous transport system has replaced multiple haulage units. Fewer but larger pieces of equipment have replaced many crushing, grinding, and flotation units. The result is less maintenance, fewer employees, and improved metal recoveries. About one-third of the $400 million modernization project is directed at improving ore movement by eliminating rail transport. The new concentrator accounts for the remaining two-thirds of the modernization investment. The modernized plant was started up in stages. In February, ore was fed to the crusher. By the end of March, the three grinding lines were operating and the flotation circuit was producing copper concentrate. In July, the design through-put rate of 70 kt/d (77,000 stpd) was reached. October saw the achievement of targeted metal recoveries that corresponded to the fully modernized operation. It is estimated that Bingham Canyon will annually produce 181 kt (200,000 st) of refined copper, 9.3 t (300,000 oz) of gold, 71 t (2.3 million oz) of silver, and 5.4 kt (12 million lb) of molybdenite. Current Bingham Canyon production is about 97 kt/d (107,000 stpd) and a similar amount of overburden. Some 70 kt/d (77,000 stpd) of ore are processed through the in-pit crusher and 27 kt/d (30,000 stpd) of ore are transported by rail. The Bingham Canyon mine has yielded more than 11 Mt (12 million st) of refined copper. In 1863, precious metals - silver-bearing lead - were first discovered in Bingham Canyon. What was once a mountain is now a huge open pit. In fact, the mine is the world's largest man made excavation. The pit is some 4 km (2.5 miles) wide and 0.8 km (0.5 miles) deep. Since the pit began operating in 1906, more than 4.5 Gt (5 billion st) of material have been removed. Modernized facilities Electric 21 m3 (27 cu yd) or 23 m3 (30 cu yd) shovels are used to load the haulage trucks. Both 154 t (170 st) and 181 t (200 st) trucks are used to haul the ore to a mobile, in-pit crusher. The crusher replaces three crushers located at the old concentrators. There are two dumping locations at the new crusher, which can handle two trucks a minute. The 1.5 x 2.7 m (60 x 109 in.), 745 kW (1000 hp) Allis-Chalmers gyratory crusher reduces the ore to 254 mm (10 in.) size or less and delivers it to the conveyor. The crusher and conveyor systems are capable of handling 9 kt/h (10,000 stph) of ore.

Jan 11, 1988

By T. B. Jarboe, H. Wen

Introduction The 150 MW circulating fluidized bed (CFB) power plant described in this article is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The ability of CFB boilers to burn low grade fuels makes it possible to burn low ranking coals or coal wastes. These include anthracite culm, coal mine rejects, and coal wash-plant-waste slurries. This article also addresses the impact of fuel characteristics on plant design. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements. The uncertain economic environment in which utilities must now operate has shifted the industry's interest away from large, base-loaded generating units to small, more versatile installations. Utilities now consider purchasing new generating capacity in smaller increments and staging its deployment to correspond with demand increases. In this way, they lower their risk in the increasingly hazardous art of long-range load forecasting. This strategy has many advantages. Multiple, smaller units have inherently greater turndown capability and better availability than a single larger unit of the same size. In addition, the smaller units will each have better cycling capability. And, with CFB combustion, the smaller units will have greater fuel flexibility. General plant description The 150 MW powerplant described here is a grassroots CFB unit. Fluidized bed technology differs from conventional combustion techniques. With CFB, solid fuel, together with inert material such as sand, gypsum, limestone, or ash from the fuel, is kept suspended in the combustion chamber. This is done by using the action of the fluidizing air distributed below the bed. Fluidization promotes the turbulent mixing conditions required for good combustion. The turbulence causes the entire mass of solids to behave like a liquid. The result is improved mixing. This allows heat to be generated at a lower and more uniformly distributed temperature that is below the ash fusion temperature of most coals. The fluidizing mechanism offers several other advantages over conventional combustion. There is less volatilization of alkali compounds, which cause deposits on boiler tube surfaces. And there is less sensitivity to the quantity and nature of the ash in the fuel. The low combustion temperatures prevent vitrification of the ash particles and minimize problems associated with furnace slagging. The ability to select from many fuels is one of the major advantages of CFB combustor technology. Fuels that can be burned in CFB plants to produce steam and electricity include: low grade coals with high ash or sulfur, lignite, peat, wood and pulp products, biomass, refuse, anthracite culm, petroleum coke, and oil shales. The plant's turbine cycle uses superheated steam at 12.4 MPa (1800 psi) and 538°C (1000°F), with single reheat to 538°C (1000°F). Two high pressure and three low pressure, closed, feedwater heaters are furnished. So is a deaerator, which is an open, direct-contact heater. The CFB plant exceeds EPA's New Source Performance Standards (NSPS) for air emissions. The design limits sulfur dioxide (SO,) emissions to 0.25 kg/GJ (0.6 lb per million Btu). SO2 reduction occurs in the combustor by reac-

Jan 11, 1988

By Kelly F. Bailey

Introduction On June 20, 1986, the Occupational Safety and Health Administration (OSHA) published revised asbestos exposure standards for general industry and construction. The standards reflect OSHA's attempt to adequately control workplace exposures to minerals it considers carcinogenic - minerals capable of causing or contributing to cancer. These standards specifically identify asbestos as: chrysotile, an asbestiform serpentine mineral; and the amphibole minerals amosite, crocidolite, tremolite asbestos, actinolite asbestos, and anthophyllite asbestos. Each of these has a more common nonasbestos mineral analog that exists in nature in a crystalline, blocky shape rather than the hair-like or fibrous shape of asbestos. The mineralogical names for three of these nonasbestos minerals are unique: antigorite for chrysotile, cummingtonite-grunerite for amosite, and riebeckite for crocidolite. The other three nonasbestos analogs do not have unique mineralogical names. They are simply designated as actinolite, tremolite, and anthophyllite without the word asbestos following their names. The 1986 OSHA standards not only cover exposure to the six asbestos minerals, they also cover specifically the nonasbestos forms of actinolite, tremolite, and anthophyllite (AT&A). The new standards regulate these minerals exactly like asbestos (OSHA, 1986). The construction aggregate industry views this as a major problem because these nonasbestos minerals are common amphibole rock-forming minerals in the earth's crust. They exist in small quantities over large areas of the United States (Kuryvial et al., 1974). These minerals, unlike asbestos, are not mined for a specific commercial purpose. They are unavoidable components in much of the aggregate used for construction throughout the US. They are also common in the gangue material of metallic ores. There are areas of the US where amphibole-bearing bed¬rock is common. Not every rock mass in these areas contain amphiboles, however. It does mean, though, that amphiboles are physically compatible with many of the rocks in those areas. And given the correct geochemical conditions, they will be present primarily in the nonasbestiform variety. In addition, these amphiboles will probably exist in the natural drainage system, sand and gravel deposits, stream sediments, lake shores, valley basins, or ordinary beach sand within these areas. There has been little quantification of nonasbestiform AT&A in dusts and soils in the US. This is not surprising since these nonasbestiform minerals are not commercially valuable. However, an example of the pervasive nature of these minerals can be found in a 1981 Geological Society of America publication where about 0.7% tremolite-actinolite was found in the desert dust in and around Tempe, AZ (Pewe, 1981). Since OSHA standards treat these common nonasbestos minerals as carcinogens in the same way as asbestos, large natural areas in the US are implicitly being labeled as hazardous by OSHA. When a substance is identified as a carcinogen, another OSHA standard comes into play, the Hazard Communication standard. There are also right-to-know laws in 9 states that essentially duplicate this federal standard. These standards require that a product containing 0.1% or more of an OSHA-designated carcinogen be labeled as such (OSHA, 1983). This means that much of the stone and sand gravel products occurring naturally and mined in the US could be labeled a carcinogen when, in fact, they are not. The National Stone Association (NSA) and the domestic construction and mining industries believe that OSHA has seriously erred. The NSA has studied the health, mineralogical, technical, economic, and legal basis for OSHA's action. These studies concluded that there is no justification for the agency regulating nonasbestos minerals as if they were asbestos. Health issues The preamble to OSHA's 1986 asbestos standard states that evidence for asbestos-like health effects from exposure to nonasbestiform varieties of AT&A is inconclusive (OSHA, 1986). The fact is, not only are the data inconclusive, they are nonexistent. During 1986-1987, NSA's occupational health and epidemiology consultant, Environmental Health Associates (EHA), reviewed all available health studies related to AT&A. EHA found evidence that malignancies in both experimental animals and humans are associated with the asbestos forms of these minerals. No experimental or epidemiological evidence was found that indicated such pathogenic effects occur from exposure to nonasbestiform varieties of these minerals. There are relatively few scientific studies of the health effects of exposure to nonasbestiform varieties of AT&A. In three different animal studies, exposure to either nonasbestiform tremolite or actinolite did not result in pulmonary fibrosis on in excess tu-

Jan 11, 1988

By Tim Neil, O&apos

Finnish mining traditions date back 400 years. The country was then one of Europe's major iron producers. Most of the mines in current operation, however, were started during the last 20 to 30 years. The Finnish mining industry must make do with limited resources. Deposits are usually low grade and small in size. Open-pit methods are used where possible. But thin ore bodies and harsh winters can impose severe restrictions. Underground mining is often the only option. Despite these handicaps, Finnish metal miners produce copper, nickel, zinc, vanadium, iron ore, cobalt, and ferrochrome. Ironically, the success of Finnish mining is rooted in a crisis the industry faced several decades ago. Mining costs were rising. High grade mineral deposits were nearly exhausted. It was vital that Finland develop new mining machinery and methods that afforded higher productivity. Cooperation between the Finnish mining industry and its equipment manufacturers was good. Partly as a result, the Finnish mining industry has turned itself into one of the most modern and efficient in the world. The Finns did this while continuing to meet the stringent safety and environmental requirements in force in the Nordic countries. Today, the share of domestic raw materials used by the Finnish metallurgical industry is decreasing. So the country increasingly depends on imports of ores and concentrates. To better provide these imports, Finnish mining companies have expanded their foreign operations. And, while importing raw materials, the mining industry has been exporting its technological and equipment know-how and expertise. Mining methods Conventional mining methods and machinery are used in surface mines. Drilling is the exception. It is done with Tamrock hydraulic track drills and 100 to 150 mm-diam (4 to 6-in.-diam) drill holes. Pumpable slurry explosives are used in larger open pits. Underground, sublevel stoping with open stopes is the most common mining method. It accounts for about 80% of all underground stoping. The main benefits of this method are low production costs, high mechanization, and easy control. The best productivity figures exceed 10 t (11 st) per man-hour, including all mining personnel. The development of cable bolting has made it possible to use sublevel open stoping even in relatively weak rock. Cut-and-fill methods, such as concrete-pillar stoping, inclined-wall stoping, and traditional cut-and-fill have also been used, combined with sublevel caving and room-and-pillar methods, according to local demands. Various fill materials and stabilization components have been investigated and tested for cut-and-fill methods. Sublevel open stopes are often later filled, to stabilize the surface or to allow pillar recovery.

Jan 10, 1988

By R. N. Chakravorty, R. J. Kolada

Introduction Spontaneous combustion in coal mining is recognized as a major hazard in terms of safety and economics. A survey by Olaf (1979) revealed that 80% of coal mine fires were caused by spontaneous combustion. Modern mining methods demand a high capital investment. Closure of a working face may then result in a huge loss. Even a short production interruption can prove expensive. Spontaneous combustion may also produce lethal amounts of carbon monoxide, thus posing a serious threat to the health and safety of underground miners. The worldwide recession in the early 1980s resulted in a number of mine closures and production cutbacks. So large stockpiles at mine sites were common. Experience has shown that stockpile fires are difficult to extinguish. Critical factors influencing spontaneous combustion There is no simple method of predicting whether a particular mining method applied to a specific coal seam will result in spontaneous combustion. Under favorable conditions of heat accumulation, spontaneous combustion can occur with any type of coal. It is known that subbituminous coals are more susceptible compared to low volatility bituminous coals, and that a high ratio of exinite increases the risk. However, the inherent moisture content of the coal and the exposed surface area may be more significant. Actual mining and ventilation conditions also strongly influence susceptibility. In practice, the experience gained with the mining method applied to a particular type of coal seam must be carefully evaluated with respect to the factors responsible for spontaneous combustion. Feng, Chakravorty, and Cochrane (1973) summarized the critical factors influencing spontaneous combustion in coal mines (Table 1). Prevention methods and strategies Mine layout is the most important factor preventing spontaneous heating. Working districts should be designed so that a particular section can be isolated on short notice without affecting production in others. Sites for preparatory seals should be identified and marked during planning. With coal seams that are highly susceptible to spontaneous combustion, the retreat method of working is preferred. This is because the gob is not subjected to a large difference in ventilation pressure. Coal pillars should be designed to resist excessive crush. The panel system of working is preferred, particularly for mining coals susceptible to spontaneous combustion. The size of each panel is calculated based on the incubation period and the rate of extraction. Controlling air leakage is also important for controlling spontaneous combustion. This is usually achieved by minimizing ventilation pressure difference, proper siting of doors, and avoiding unnecessary stopping and starting of fans. Air leakage is also reduced by sealant coating, injection of cements in cracks and crevices, and by maintaining good gateside packs. Application of inhibitors to control spontaneous combustion met with limited success. Chamberlain and Hall (1973) concluded that borate solution or Montan powder sprayed in the gob area or infused into a low rank coal would reduce the possibility of spontaneous combustion. Early detection of heating Significant research is being conducted worldwide to develop methods for early detection of heating. Monitoring combustion products during the early stage of heating is the most suitable method for detecting spontaneous combustion. The major gaseous products resulting from low temperature oxidation of coal are carbon dioxide, carbon monoxide, and water vapor. In mining operations, carbon dioxide monitoring is considered unsuitable because there are sources other than spontaneous heating from which this gas may originate. Carbon monoxide, however, is a more specific product of combustion during low temperature oxidation of coal. Over the years,

Jan 10, 1988

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988

By H. Colijn

Introduction Bulk commodity prices are ever increasing. This forces buyers and sellers in world markets to look more carefully at methods for obtaining an accurate accounting of commodity transactions in commerce and materials utilization in processes. Weighing and sampling inaccuracies can result in loss of income, product quality, and cost controls. So weighing and sampling accuracies are extremely important. They are the key components of managing the quantity and quality control aspects of bulk materials handling. This article will confine itself to the weighing systems and will deal with various aspects of system design, calibration, and operations. Emphasis will be placed on new developments and requirements in this field. Weighing methods To measure the gravimetric pull on a body being weighed (the load), the gravimetric force must be countered by an opposing force. Measuring this counter-balancing force thus becomes the measurement of weight. The conventional even-arm balance shows the concept of balancing an unknown mass with an equal known counterbalancing mass. But the loads encountered in industry generally range up to many thousands of pounds. So it is obvious that the even-arm approach is not practical. Thus, with the exception of direct load-bearing load cells, most of the weighing equipment uses some form of lever system. This is usually a combination of first- and second-class levers, to gain a mechanical advantage. These levers permit the load force to be counter-balanced and hence measured within a practical range. Lever systems not only perform this force-reducing action, they also serve to focus the load force at a single point, for convenient measurement. They align the force vertically in one direction so that measurement accuracy will not be affected by unrelated side forces. There are five basic methods of gravimetric weight measurements. That is, there are five basic types of opposing forces. • The first is the standard weight counterbalance. It uses a known weight to counterbalance the load directly or through a lever system.

Jan 9, 1988

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988