Search Documents

By John W. Amos, John A. Christophersen

The Deister No. 7, "77" and "88" Coal Washing Tables have been used by the coal industry in the cleaning of finer sizes of coal (-1/2") since washing of coals became necessary. This paper will deal with the in-plant use of the CONCENCO "88" Deister Coal Washing Table, along with a brief description of the Deister Refuse Superscalper. Efficient in-plant operation of the Deister Coal Washing Table can be accomplished by the adjustment of six basic variables. These variables are: 1. Headmotion 2. Feed 3. Riffle Pattern 4. Dressing Water 5. End Elevation Adjustment 6. Side Tilt Adjustment VARIABLE NO. 1 HEADMOTION The reciprocating movement of the "88" Table is developed within the headmotion entirely by rotating eccentric weights. Four parallel shafts each carry pairs of eccentric weights (Figure 1-A). The shafts are geared together with gears of 2 to 1 and 1 to 1 ratios, so that the two shafts in vertical alignment which carry the small eccentric weights operate at twice the speed of the other two shafts. The other two shafts are also in vertical alignment with each other and carry large eccentric weights. As power is supplied to one high-speed shaft, once each revolution the forces produced by the large eccentric weights are reinforced and then opposed by the small eccentric weights in a horizontal plane. The direction of movement of the table decks is reversed much more sharply at the forward end than at the backboard end of the stroke, causing material to move toward the refuse end of the table. Because in the vertical plane all centrifugal forces oppose each other and cancel out, there is no vertical movement and virtually no impact to the support steel. The "88" Coal Washing Table is suspended by wire-rope cables from three overhead steel beams, and operates with a perfectly uniform and exact differential motion curve in every stroke (Figure 1-B). The decks, being attached to the headmotion, are reciprocated in a parallel line from the head- motion to the refuse corner at speeds varying from 260-300 strokes per minute. Both length of stroke and speed are set at the factory for the coal characteristic desired and should not be changed. A 3 HP motor is mounted on the top of the headmotion and uses 3 V-belts to transmit driving power to the headmotion. The headmotion must be kept running on a horizontal plane. Punch marks are provided on the side and end of the main frame for use in leveling the motion (Figure 1-C). In leveling the motion, the work must always be done with two cables. To level the long side of the headmotion both front or both rear cables are raised or lowered to bring motion back to level. To level side to side, both right side cables or left side cables are raised or lowered to bring motion back to level VARlABLE NO. 2 FEED When tabling different size coals, each deck of a "88" DIAGONAL-DECK Coal Washing Table will handle feeds as described in figure 2-A.

Jan 1, 1988

By K. M. Reim

Planning the development of the Quartz Hill molybdenum open pit mine in Southeast Alaska required a number of special considerations. Located in mountainous glaciated terrain, about 3.8 m (150 in.) of annual precipitation (with annual snowfall over 10.2 m (400 :in.) was a primary consideration. Mine planning included muskeg and snow removal, avalanche control, clearing timber, water quality control, dust control, seismicity, mine schedule, work force and reclamation. Quartz Hill is in an environmentally sensitive area which has required extensive environmental baseline data collection, four Environmental Impact statements (EIS) and a large number of permits.

Jan 1, 1988

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By K. P. Madhusudhanan, R. K. Bhatia, K. S. Narasimhan, R. N. Singh

A typical case study of a coal washery of capacity 500 t/h raw coal input has been presented and discussed with particular reference to the techno-economics for flotation column vis-a-vis the conventional flotation cells, keeping parameters like input capacity and product ash same. The results presented indicate that substitution of flotation cells by columns in a coal washery results in advantages of increased fine coal recovery, better quality of concentrates, lower capital and production costs etc.,. The effect of increasing the specific capacity of the column by design modifications on the cost benefit is also analysed.

Jan 1, 1988

By G. W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment®, two new lime substitutes for treating acid mine drainage (AMD), have been compared with lime and Allcament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with Environmental Protection Agency (EPA) regulations. Material utilization and optimum pH are reported.

Jan 1, 1988

By Risto Lindsberg

A wide concept of flotation equipment and technologies is presented in this paper. The basis for the presentation in Outokumpu's world-wide experience in mineral processing and other related areas, and continuing research and development work done in Finland as well as abroad by Outokumpu's subsidiaries (and customers). It is understood that flotation equipment selection for a certain process stage is becoming more complicated. It is obvious that flotation equipment in grinding circuit needs different design from a multistage cleaning process. In this paper, column flotation is compared with other flotation methods. Thus three areas of flotation are discussed in this paper: 1. Flotation in the grinding circuit, Skim-Air machines 2. Rougher-scavenger flotation, conventional cells vs columns 3. Cleaning flotation, columns

Jan 1, 1988

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By N. S. Harding, M. C. Mai, A. G. Fonseca

Many coal characteristics affect combustion performance. Mill wear, boiler efficiency and derate, slagging, fouling, and ash collection and removal are only a few of the impacts of coal quality on boiler performance. The ability to assess fuel characteristic impacts on busbar costs is essential, although difficult to obtain. The relationships between coal characteristics and ignitability, operability, slagging, and fouling were investigated. The examination of combustion data/performance from a laboratory study, a boiler simulation system (pilot combustor), and commercial boilers indicated the benefits of burning improved quality coal. The specific effects of cleaning are discussed. A validation of the necessity of commercial-scale and/or pilot-scale testing is presented.

Jan 1, 1988

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By J. R. Aggson

In an effort to minimize cutter roof failures in longwall development entries of a West Virginia coal mine, a three-entry system was developed with the center entry arched into the strata above the coal seam. The purpose of the arched entry was to modify the horizontal stress envelope associated with the three-entry system and improve roof conditions in the adjacent outside entries. Contrary to the predictions of elastic analyses, the presence of the arched entry improved roof conditions by eliminating cutter roof failures in the outside entries. In-situ stress determinations and numerical modeling techniques were employed to quantify the impact of the arch and investigate the mechanism of stress relief associated with the arched entry. Stress determinations and underground observations indicated that the roofs of the outside entries were within the zone of stress relief generated by the arch, and that failure or movement along bedding plane discontinuities played a major role in the formation of the stress relieved zone. The numerical model incorporated horizontal joints to simulate bedding plane discontinuities. The properties of the joints were adjusted until roof stresses predicted by the model were in agreement with measured stress profiles. This process resulted in a calibrated analytical tool that could be used to evaluate alternate mining geometries.

Jan 1, 1988

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By I. D. Lindley

The Wild Dog vein gold deposit in East New Britain Province, Papua New Guinea, forms part of a recently discovered 26 km zone of auriferous quartz vein mineralisation. The deposit, which was discovered in July 1983, has no silt anomaly, and a panned concentrate anomaly and float train restricted to within 500 m and 800 m respectively, of the discovery outcrop. Discovery of the Wild Dog deposit was a result of the methodical followup of regional panning which, as followup progressed, was replaced in importance by float sampling. Of the sampling methods used during the exploration leading to discovery, panning and float followup provided immediate indications of the presence of mineralisation. This high degree of spontaneity of followup is not provided by geochemical techniques, and has obvious advantages in high cost exploration for precious metal deposits in remote locations.

Jan 1, 1988

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By S. K. Kawatra, K. A. O, DeLa&apos

On-line sensors and process controls are important for efficient operation of coal preparation plants. The objective of this paper is to describe the current practice in on-line measurement of composition, density, moisture, level, flow and weight. This paper also discusses how on-line sensors can be implemented in process control, and how sensors which are currently being developed can be utilized.

Jan 1, 1988

By C. L. Elmore

This paper describes a new development in the cyanidation of gold ores, which we expect will result in a major improvement in the way many gold ores are treated. The process has evolved through work at Hazen Research, Inc. for Kamyr, Inc. and in brief, the consists of utilizing oxygen rather than air in the carbon-in-1 each (CIL) process. We refer to this improved process for all ores amenable to cyanide leaching as carbon-in-1each with oxygen or CILO.

Jan 1, 1988

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By R. O. Burt

The Tanco pegmatite is located in the Bird River greenstone belt of south-eastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). The orebody was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANCO), and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco's currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Corporation, and the Province of Manitoba.

Jan 1, 1988

By Richard J. Adams

Coal jigs have played a predominant role in U. S. coal preparation for fifty years. Recently, an improved fine coal jig has been used to prepare the middle size range coal. These efficient machines are changing the historical thinking about jigs and is consistent with trends in coal preparation throughout the world. The performance achieved and operating cost savings are causing a change in fine coal cleaning strategy. With the exception of a handful of operators, fine coal jigs are generally not well understood by the industry. The objective of this paper is to provide some insight into the past use of fine coal jigs and their potential in the future. Improved Fine Coal Jig Since the mid 701s, an improved fine coal jig has been employed to an important niche in preparation, the 19 mm x 100 M range of cleaning. Several factors due to mining and liberation considerations have caused an expansion of this middle range of coal resulting in a host of challenges for coal preparation engineers. Fine coal jigs have been commissioned in several installations in North America to handle these important applications as shown in Table No. 1.

Jan 1, 1988