Search Documents

By S. Managi, M. C. Williams, N. H. Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key-technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate or hydroxide electrolyte. Since a pure stream of CO2 is produced the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology. INTRODUCTION The DCFC has been under development for many years. It was researched as early as 18961), but an intense research and development is necessary to realize its potential. William W Jacques, a US electrical engineer and chemist, described a DCFC in 1896 in US Patent 555511 for a “Method of converting potential energy of carbon into electrical energy”. Jacques used coke electrodes in a molten NaOH electrolyte. Molten carbonate fuel cell (MCFC), solid oxide (SOFC) or hydroxide electrolyte (AFC) technologies can be used as the basis for the DCFC technology. A schematic of the direct carbon fuel cell in the MCFC mode is shown in Figure 1. The molten carbonate fuel cell operates at approximately 650°C (1200°F). The high operating temperature is needed to achievesufficient conductivity of the carbonate electrolyte, yet allow the use of low-cost metal cell components. A benefit associated with this high temperature is that noble metal catalysts are not required for the cell electrochemical oxidation and reduction processes. For the hydrogen reaction the half-cell electrochemical reactions are

Jan 1, 2019

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By Pengfei Wang, Guorui Feng, Shufeng Zhang, Yuxia Guo, Tingye Qi, Dian Li

"Based on the geological conditions of the No. 10203 mining face of the Xinyang coal mine, a numerical model of the longwall backfilling face is built using the FLAC3D software to calculate the limit broken length of the key strata. Based on the deformation laws of the immediate roof, the backfilling parameters are determined. Furthermore, the movement laws of the overburden strata with different volume filling rates (0, 40, 60, 100, and 100%) and with different layout forms of the filling strip (under a volume filling rate of 60%) are analyzed. The results of the numerical modeling show that the stress of the two sides of the working face and the deformation of the overlying rock are gradually reduced with the increment of the volume filling ratio. In view of the deformation of the roof strata within the allowable range, a volume filling rate of 60% is selected to simulate and analyze the filling effect under different layout forms of the filling strip. The filling width, stress concentration area, and layout form of the filling strip are the key factors to control the movement of the overlying strata. In addition, the probability integral formula is used to calculate and predict the ground subsidence on the filling area, which confirmed that the backfilling mining method is fully applicable in the Xinyang coal mine. The results of this study provide a certain theoretical basis for the determination of the filling process in the field.INTRODUCTIONIn China and other coal producing countries, gob is managed using the caving, filling, supporting, and slowly sinking methods (Zhang, Zhou, and Zhang, 2009). With the continuing development of the concept of green coal mining (Guo, Deng, and Zou, 2004), the filling method, which is safe and environmentally friendly, has been widely used in the field. On one hand, this method could reduce waste rock and other waste discharge. On the other hand, it could effectively slow the surface subsidence. Recently, strip-filling mining mostly adapted the arrangement of the strip backfill with equal intervals and widths (Xie et al., 2004), but the reasonability of this arrangement should be discussed. To arrange the intervals and width of the strip-filling body reasonably, Feng et al. (2019) put forward the “constructional backfill mining (CBM)” concept. The CBM is a type of backfill mining with low backfill rate, strong structural stability, and good backfill effect. The targets of the CBM include the efficient usage of solid waste resources in mining areas to reduce the backfill cost, the improvement of backfill materials and backfill technologies to increase the backfill efficiency, and rational planning of backfill and mining scheme to reuse the underground mining space. The determination of proper width and intervals for the strip-filling body is the main content of the CBM. Strip-filling mining using cemented coal gangue backfilling is the main method to undertake overburden of the overlying strata and to slow down the surface deformation. It also plays an effective role in cost reduction (Xu et al., 2007). This study focuses on proper determination of the strip-filling body parameters according to actual geological conditions by a simulation. It provides an appropriate reference for backfill mining in the Xinyang coal mine."

Jan 1, 2019

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By Fulian He, Jianhang Chen, Shoubao Zhang

"Fully grouted rock bolts have been used in mining industry for many years. Significant research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs. However, compared with that, less work has been conducted with analytical modelling. Therefore, in this paper, the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts. To confirm the credibility of this analytical model, an in-situ pull-out test was used to validate this model. There was a close match between the experimental result and the analytical result. Following this, a parametric study was conducted with this analytical model. The influence of coefficients, Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts were studied. Furthermore, the load distribution along the fully grouted rock bolt was analytically studied. The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load. However, the trend of the load distribution curve was influenced by the pull-out load. This paper was beneficial to better understand the load transfer mechanism of fully grouted rock bolts.INTRODUCTIONRock bolts have been used in the mining industry for a long time. They are used as the reinforcement tendons to keep the stability of openings in underground mining and the slope in open-pit mining. Furthermore, rock bolts are commonly used not only in the mining engineering, but also in civil engineering (Thompson, Villaescusa, and Windsor, 2012).The rock bolt is a tendon which can be a rod or a cable inserted into a borehole drilled in rock masses or soils. Traditionally, the material of rock bolts was steel. However, engineering practices showed that the steel rock bolts can be easily corroded by the moist environment in underground mines. Next, Fiber Reinforced Polymer (FRP) was used to manufacture rock bolts, which are termed as FRP rock bolts. Experimental results proved that the FRP rock bolts can effectively reinforce the surrounding rock masses without being corroded (Wang et al., 2018)."

Jan 1, 2019

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By Pengfei Wang, Guorui Feng

"With the depletion of easily minable coal seams, less favorable reserves under adverse conditions have to be mined out to meet the market demand. Due to several historical reasons, a large amount of remnant coal was left unrecovered. One such case history occurs with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Coal Mine, Shanxi Province, China. The challenge that the coal mine is facing is that there is an ultra-close coal seam right under it, with an only 0.8 to 1.5 m sandstone dirt band in between the two. The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving (LTCC). The remnant coal pillar was induced to cave in as top coal in LTCC system. Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata. The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars. The gob development (roof strata cave-in) is intermittent with the cave-in of these coal pillars and the sandstone dirt band. FLAC3D numerical modelling shows that the multiple seam interaction has a significant influence on mining-induced stress environment for mining of lower panel. The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found. This demonstrates that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below them.INTRODUCTIONChina is one of the world’s coal-rich countries. Coal has played a significant role in the growth of China’s economy. Coal reserves have been mined commercially in China for over one hundred years. The demand for coal in China is still going to grow at a relatively high rate (BP Energy Outlook, 2019). Long-term large-scale and intensive coal mining activities have created tension between increased demand and limited resources (Bai et al., 2018). Easily minable coal seams such as sub-horizontal, tabular, and laterally extensive coal seams are being depleted, and therefore the remaining reserves are becoming less favorable. However, in many situations, the coal reserves under adverse conditions have to be mined out to meet the market demand for energy.Due to sedimentary environments and geological conditions, many coal seams are interspersed with sedimentary bands, or partings both within an individual seam and between seams. These bands and partings lead to appearance of ultra-close coal seams, as well as giving rise to considerable variation in their structural and mechanical properties (Ghabraie and Ren, 2016). Difficulties are encountered in the mining of such coal seams. If ultra-close coal seams are mined sequentially, that requires the design of a mining system for each individual coal seam; also, a large number of gateroads have to be excavated, which is not a high-efficiency option. If ultra-close coal seams are mined at a great mining height at once, for instance, using longwall top coal caving—a longwall mining method that is widely used in China for the mining of ultra-thick coal seams—then the location and characteristics of the band would have a significant influence on success of their extraction."

Jan 1, 2019

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By M. Visnjic

Open Pit Mine Production scheduling under commodity price uncertainty suffers from an exponentially increasing problem size as simulations and real options flexibility are used to generate and evaluate multiple production schedules. Robustness evaluation techniques attempt to evaluate a production schedule that is generated on a single set of economic parameters against several varying prices and sources of uncertainty. This approach is invalid as the corresponding optimal LOM mine plan will change for each set of evaluation parameters. Using commodity market futures and treasury bonds as production schedule economic input parameters provides fully price and time-value-of-money risked scheduling parameters that maintain a deterministic problem size. This paper will provide comparative analysis of project NPV’s coming from traditional price uncertainty evaluation based on a single fixed LOM mine plan using varying prices versus evaluation based on varying LOM plans that are both generated and evaluated using varying prices. When cross evaluating constant price mine plans against simulations, the upside potential and downside risk of a project are significantly misrepresented. INTRODUCTION The life of mine (LOM) production scheduling problem seeks to answer the question of from where and when to extract a given block within the ultimate pit limit as well as where and when to process it. Solving this problem takes into account the constraints of extracting any particular block while seeking to maximize the net present value (NPV) of the mineral asset as a whole. A direct driver of the value of a block, and there for the entire asset, is the market price of the commodity in question. Complications arise when an optimal production schedule is attempted to be solved under price uncertainty. Many solution methodologies have been proposed in an attempt to optimize under this criterion, yet there are three salient aspects that are overlooked during this process. They are: • Generating a single production schedule and evaluating it against many simulated price paths. • Failing to understand the mechanism describing particular commodity price behavior • Inappropriate risk adjustment In an effort to address these aspects of production scheduling under commodity price uncertainty, we propose a methodology to define the economic parameters as input that is applicable to most if not all production scheduling approaches. This methodology will not only simplify the production scheduling process in terms of establishing block value but utilizes the risk adjustment of real options valuation to avoid the arbitrary blanket risk adjustment of traditional discounted cash flow valuation. Our findings conclude that attempting to optimize around individual price paths is futile and using a market risk adjusted single price forecast provides a justified economic basis for production scheduling while maintaining the same problem size as a deterministic production scheduling problem.

Jan 1, 2019

By S. K. Kawatra, V. Claremboux, S. Valluri

Carbon dioxide capture from coal-fired power plant flue gas and subsequent sequestration is expected to play a vital role in mitigating global climate change. To meet the growing need for CO2 capture Technology, Michigan Technological University is researching CO2 capture and Utilization. We have successfully converted CO2 into oxalic acid using an electrochemical approach. If oxalic acid can be produced in bulk from CO2, it can be used to leach rare earth minerals at low cost. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. In this paper, we will present an idea of how the factors mentioned above will effect the electrochemical reduction of CO2 to Oxalic acid. INTRODUCTION. CO2 is thermodynamically quite stable, as shown by its highly negative heat of formation. Thus, it is expected that the formation of any useful chemical from CO2 will require the input of at least as much energy as geological sequestration. However, to be more effective the resulting economic value of the chemical need only pass the cost of the additional energy required beyond geological sequestration. This lends itself to two extremes: one where the quantity of energy required is low and one where the economic value of the additional energy is low. It is expected that CO2 can be reduced via electrolysis to several compounds. Of particular interest are formic acid, oxalic acid, methanol, ethanol, formaldehyde, and carbon monoxide (as a component to syn-gas). These chemicals have been reported as electrolytic products previously in literature and have considerable potential for application. EXPERIMENTAL Electrocatalytic Production of Oxalate from CO2 We are using membrane electrolysis cell to produce oxalate from CO2. A membrane electrolysis cell is a 2-chamber electrolysis cell where the chambers are separated by a selectively permeable membrane. To produce oxalate, a cation exchange membrane (which selectively exchanges cations) was used. Previous literature suggests that in the cathode chamber an organic electrolyte, such as tetraethylammonium perchlorate or tetraethylammonium bromide in dimethylformamide, are preferred3. In the anode chamber, a sodium hydroxide solution water is used. Carbon dioxide is then bubbled into the cathode chamber as a current is applied.

Jan 1, 2019

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By F. L. Pirkle, W. C. Bagby

The International Mineral Valuation (IMVAL) Committee, founded in 2012, develops strategies for conducting mineral valuations. These strategies have been developed into a mineral asset valuation template called the International Mineral Property Valuation Standards Template and is part of IMVAL's work to establish consistent international standards for mineral property valuation and reporting. This template is a living document that is updated from time to time and is based on three core values or pillars (Fundamental Principles): Competence, Materiality, and Transparency. Objectivity, Independence, and Reasonableness may be applied as required by national codes or standards. The Template harmonizes international standards for valuation of mineral assets as real property and represents a consensus of current good practices. It is not a stand-alone reporting code and does not supersede existing national reporting standards. The Template deals with mineral-property valuation as distinct from mineral-project evaluation. INTRODUCTION In his 1989 book, “The New Realities”, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, California, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized.” (p. 209) The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze, and interpret data that are material to a mineral valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality, and transparency, the three pillars of mineral valuation (“minerals valuation”, “mineral-property valuation”). The International Mineral Valuation Standards Template (“IMVAL Template”, IMVAL”, “Template”), third edition dated May 2018, defines mineral valuation as: “The estimation of the Value of a Mineral Property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the Valuation conclusion) or to refer to the preparation of the estimated Value (the act of valuing).” (p. 14) Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The Template deals with Valuation, which is distinct from Evaluation. The distinction inherent in these defined terms is that Valuation addresses the estimation of value of a Mineral Property, whereas Evaluation addresses the broader assessment of a Mineral Property for an investment decision.” (p. 2)

Jan 1, 2019