Search Documents

By R. A. Womack, Alex Ruzycki

Over the past six years, 4.5 million tonnes (5.0 million short tons) of gold ore have been heap leached at the Alligator Ridge Mine. Ore is leached in successive lifts, resulting in heap heights of 20 m (66 ft). Recoveries from each lift are determined through an extensive post-leach drilling program. The relationships between heap height, recovery rate, ore preparation, heap construction, and leach solution application are discussed.

Jan 1, 1987

By H. Wesley Peirce

Arizona embraces portions of two major western-U.S. physiographic-geologic provinces and a smaller, local one. These exert fundamental control over the geologic framework and associated earth-material resources and potential. The Mogollon Rim diagonally crosses the State and separates the Colorado Plateau Province to the northeast from the Transition Zone and Basin and Range Province to the southwest. More than 90 percent of the population, production of nonfuel minerals, agricultural land, and water resources are in the Basin and Range part of the State. In 1981 Arizona was ranked number one in the Nation with respect to the value ($2.56 billion) of nonfuel-mineral production. About 8.2 percent of this amount ($212.9 million) can be attributed to nonmetallic (industrial) materials. Although a diversity of nonmetallic substances is produced and some are exported, the bulk is utilized within the State and is directly related to market growth. Since 1950 there has been a fourfold increase in Arizona's population, a concomitant twelvefold jump in sand-gravel production (tons), and a twentyfold increase in "stone" production. New industries developed during this time include cement, salt (and storage of liquid petroleum gas products in solution cavities in salt), zeolite, hydrofrac sand, vitrified clay pipe, crushed marble products (teed additive, pool sand, roofing granules, etc.), and "rock" wool. Most of these newer industries serve out-of-State as well as in-State markets. In 1981 at least 225 industrial mineral or rock deposits were being worked to produce about 10 tons of material per Arizona resident per year. In 1980 the relative values of basic industrial minerals produced in the State, by major group, were cement and lime (51.6 percent); gravel (26.5 percent); sand (11.8 percent); stone (4.6 percent); and others (5.5 percent). Detailed knowledge of the nonmetallic rock-and-mineral content of most Arizona ranges and basins is lacking. Exploration opportunities in this sun-belt growth region appear encouraging.

Jan 1, 1987

By C. I. Wilmot

The paper presents an update of the Paradise Peak mill after the first year of operation. Process revisions, equipment modifications and additions, and personnel requirements are discussed with a comparison to original design. All areas of milling are discussed including crushing, grinding, leach/countercurrent decantation (CCD), precipitation, refinery, and heap leach.

Jan 1, 1987

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By A. D. Agate

In developing nations, novel mineral processing methods like bacterial leaching are gaining prominence. The principles and practices for isolation and preservation of cultures used in bacterial leaching are discussed with special reference to cultures used in leaching copper from Indian ores. In all, 145 potentially useful microorganisms such as iron- and sulfur-oxidizing bacteria were isolated from various ecosystems of the copper mining areas in the country. The major organisms isolated by enrichment culture technique belonged to T. ferrooxidans and T. thiooxidans species. In addition, thermophilic cultures like Sulfolobus sp. and thermophilic thiobacilli were also isolated. The process of copper leaching was scaled up to the 300-kg level in PVC columns. Since the preservation of efficient cultures in active state was vitally important, a new method was devised that preserved the activity of thiobacilli for a period of more than two years. The novel method of storage in sterile chalcopyrite ore at 8°C can be considered an important advance.

Jan 1, 1987

By P. C. Kapur

The hierarchical relationship between three broad kinds of grinding models for a spatially homogeneous, linear, time-invariant batch grinding system are first established. Limiting and asymptotic arguments for arriving at approximate but simpler models are employed in all three cases. These parsimonious models -provide alternate and, in some respects, more incisive and convenient tools for the analyses of grinding processes and simulation of comminution circuits. In the discrete-size, discrete- time class of models, a reduced mill matrix is derived, which is seemingly adequate for those grinding circuits whose identification otherwise is difficult because of limitations on the quantity of data and its quality. In discrete-size, continuous-time types of models, parameter lumping has been employed for obtaining a G-H solution which is quite accurate and exceptionally useful for graphical display of data, model verification, and parameter estimation and simulation. In continuous-size, continuous-time models, a similarity transformation is used for solving the integrodifferential equation of grinding. This solution provides a unified framework for a number of apparently diverse empirical grinding phenomena such as self-preserving behavior of ground particle size distributions and energy laws.

Jan 1, 1987

By O. Fernandez, M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material buildup inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design, and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 t/d (1100 stpd) and significant operating costs savings.

Jan 1, 1987

By D. A. Knight, V. G. Medina

Kidston's 14 000 t/d mine and mill complex in Queensland, Australia, started operation in January 1985. During its first 18 months of operation, the mine produced over 7000 kg (225,000 oz) of gold, making it the largest gold producer in Australia. This paper describes the planning, logistics, flowsheet, and process for the Kidston project, and some of the problems encountered during startup and the measures taken to correct these problems.

Jan 1, 1987

By A. J. Neale, B. C. Flintoff

A relatively inexpensive and reliable method of using liquid phase tracers to aid in the solution of material balance problems is introduced. The method is of value in situations where one is required to calculate a material balance around a process that has the operating appearance of a "blender" or "splitter" with respect to the available slurry sample data. The paper briefly reviews material balance development and tracer applications in mineral processing, introduces the problem to he addressed, and provides both theoretical and industrial evidence establishing the potential of the method.

Jan 1, 1987

By M. G. Ayat, B. C. Scott

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling, and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent on the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1987

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

INTRODUCTION Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 1, 1987

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By E. R. Bollinger, N. S. Tanious, R. D. Beckett

The US Bureau of Mines developed hand-made, steel-fiber-reinforced concrete (SFC) blocks for building mine cribs. To ensure wider usage of these cribs, US Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Co. to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated to determine their compressive strength and post failure characteristics. After testing and adjusting of various concrete mixtures, a final formulation was selected that gave a nominal crib strength of 22 MPa (3200 psi) and a nominal modulus of elasticity of 6.9 GPa (1.0 x 106 psi.) These SFC cribs can support 6.4 times as much as a wood crib with the same load-bearing area. The SFC crib was proven to be an economical and effective roof support system through various underground installations.

Jan 1, 1987

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By M. A. Mahtab, N. M. Cruickshank, M. T. Wane

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment, and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) microseismic activity. Geophysical and engineering methods for detecting these characteristics are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1987

By R. J. Sweigard

One of the foremost problems in reclaiming prime farmland is compaction of the subsoil which is caused by the reclamation equipment. Wheel tractor-scrapers are most commonly used to replace subsoil and have been blamed for the majority of the compaction problems. Two methods of alleviating this problem that are presently being considered are mechanical subsoil loosening machines and truck- shovel combinations for subsoil handling. A field study was conducted in which dry bulk density measurements were taken in an effort to determine the effectiveness of truck-shovel combinations and subsoil loosening equipment in reducing bulk density in comparison to typical scraper replacement.

Jan 1, 1987

By J. H. Bassarear, P. F. Thomas

Large-scale equipment can reduce both capital and operating costs for concentrators. Large semiautogemus (SAG) mills can be effectively utilized in big mills but they must be kept fully loaded to tab advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semiautogemus mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4476 kW (6000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 t/d (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and jive variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1987