Search Documents

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure and other types of sensors are increasingly used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in the new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP), while older forms of serial communication are being retired. This paper presents the selection, configuration and testing methodologies employed by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide IP data transport.IntroductionTo enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry (Zhou et al., 2017). However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology infrastructure in place to handle the data transport requirements for the newer Internet Protocol (IP)-based technologies that are part of IIoT.This was the case with a mine in the Western United States. It lacked the infrastructure to perform critical monitoring in remote headings. Therefore, the mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for the real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder communications system to achieve IP data transport using commercially available land mobile data radios (NIOSH, 2013; Forooshani et al., 2013; Novak, Snyder and Kohler, 2010; Yarkan et al., 2009). The solution, fully evaluated in laboratory and mine environments, requires no modifications to the existing system, is economical, simple to implement, and reliable. It also allows for transition to higher-bandwidth IT networks, such as fiber optic or WiFi, should they become available."

Dec 1, 2018

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 11, 2018

By William Gleason

"Technology of all forms has experienced exponential growth in recent years, and there is no sign of it slowing down. This growth has presented amazing opportunity and significant challenges in nearly every aspect of daily life. Some of these changes are seen and experienced every day as we turn to our smart phones, tablets and smart watches to help with us with everything from directions to the store to managing our health. And other technological growth takes place far away from the public view but can have as much of an impact on our daily life as does shopping at Amazon or connecting with friends on social media.At the “THRIVE 2018, Innovations Advancing Mining” conference presented by SME on Sept. 27 at the Sheraton Pittsburgh Hotel at Station Square in Pittsburgh, PA, the focus was on innovation and how it affects the global mining industry.More than 100 people were on hand for the inaugural event, and they were treated to a unique program that focused on the cutting-edge innovations that will carry the mining industry into the future while increasing safety and productivity along the way.2018 SME President Barbara Arnold was the driving force behind the conference and put together the technical program with a focus on innovation through the entire mining life cycle and into the future. Talks ranged from more efficient and safer ways to extract minerals to some of the most advanced end uses of minerals and metals, including the use of 3D printing to create precision parts for machines and humans from advanced metal alloys.“We need to adapt new technologies to our industry and develop additional technologies as we provide materials and metals for infrastructure and energy development in the United States, around the globe, and to the Moon and beyond,” Arnold told Mining Engineering. “Our inaugural THRIVE conference sets the stage for these innovations to be applied and to continue to be developed. Our mining industry can only continue to thrive with these advances.”"

Jan 11, 2018

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By S. S. Klima, D. E. Pollock, J. A. Organiscak

"Airborne respirable coal dust capture by water sprays or wet scrubbers has been studied and developed over many decades as an engineering control to reduce dust exposure in coal mines and combat coal worker pneumoconiosis. Empirical relationships and deterministic models for particular dust capture experiments have previously been devised to show the key parameters involved in airborne coal dust capture. Many of the results from these models show that the significant parameters related to airborne dust capture are water spray pressure, water quantity, water droplet size, relative water droplet-to-dust particle velocity, and total operating air pressure of the scrubber. However, many airborne dust capture efficiency relationships and models developed for particular experiments cannot be readily applied to forecast the dust collection efficiency of different spray and scrubber design configurations, which rely on several key dimensional engineering measures. This study examines engineering measures from previous water spray and wet scrubber experiments conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and the U.S. Bureau of Mines (USBM) to develop empirical models for wet collection of airborne dusts. A dimensionless empirical model developed for predicting airborne dust capture efficiency of water sprays and wet scrubbers is presented. IntroductionWater sprays have been one of the earliest mainstay engineering controls used to suppress respirable dust in underground coal mines. Some of the earliest reports of water spray usage on continuous mining machines indicated respirable coal mine dust reductions of 20 to 60 percent (Kobrick, 1970). Not long after the enactment of the 1969 Coal Mine Health and Safety Act, the U.S. Bureau of Mines (USBM) and others conducted extensive research into water spray and wet scrubber systems to control respirable dust in coal mines. The primary aspects of water spray dust control included prewetting for dust prevention, localized ventilation redirection and airborne dust capture, which are summarized in handbooks or best-practices guides (Kost, Yingling and Mondics, 1981; Kissell, 2003; Colinet et al., 2010). Initially, underground studies were conducted to identify the primary sources of dust during the mining processes and effective dust controls (Courtney, Jayaraman and Behum, 1978; Jankowski and Organiscak, 1983). Laboratory research systematically studied ventilation and airborne dust capture effects of water sprays and scrubbers to improve their application in underground coal mines (Tomb, Emmerling and Kellner, 1972; Divers and Janosik, 1978, 1980; Grigal et al., 1982; Ruggieri et al., 1983; Jayaraman, Jankowski and Kissell, 1985; Volkwein, Ruggieri et al., 1985; Jayaraman, Schroeder and Kissell, 1986; Divers, Jankowski and Kelly, 1987; Jones and James, 1987)."

Jan 10, 2018

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By Stuart Lister

"When MacLean Engineering chairman and founder Don MacLean got the first question from a minesite about the possibility of addressing ventilation limits through incremental fleet electrification, he was intrigued. It was back in 2015, and the MacLean scissor bolter was already diesel-electric (jumbo trailing cable), so it made sense to him that if they could engineer a battery drive system for the unit’s tramming cycle, they would have the inaugural electric vehicle (EV) MacLean unit.At that time, there were not any entirely diesel-free hard rock mines in existence on the planet, and that remains the case to this day — although the Borden project in northern Ontario is progressing toward that goal (see page 33). This meant there was essentially zero market demand for battery electric vehicles as well as a complete lack of battery technology to address the battery electrification of heavy haulage. Heavy haulage is the part of a typical mine’s mobile fleet with the largest footprint when it comes to diesel particulate emissions, greenhouse gases and wasted energy in the form of heat.Three years later — the wave of battery electrification that is currently picking up speed across the mining industry promises to hit full swing by the early 2020s when a slew of new build, diesel-free mines will start construction. But this movement toward emissions-free mobile fleets is not a completely new phenomenon. Instead, it is an updating of mining technology from a previous generation. What is going on now is the re-electrification of mining. Up until the 1960s, early generations of battery technology (lead acid) and electric locomotive systems were the norm for material and ore haulage in Canada and elsewhere.The thought of a coming paradigm change in mining was particularly pertinent to Don MacLean back in 2015, as he had been part of the era that ushered in the first generation of rubber-tire diesel equipment, when he was a divisional foreman with Inco in Sudbury in the 1970s. He was part of the operating team that was tasked to build a rail loop on one extraction level of the mine. At that time, events on the ground overtook the project, as diesel-powered mobile equipment became a viable option. Once the first diesel scoop was introduced at Creighton #3 shaft, it was clear what the power, haulage capacity and mobility could do for operations and that era of electric rail haulage underground was effectively over."

Jan 10, 2018

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By Konner Horton, Adam L. Bedell, Don Del Nero, Brian Jones

"The City of Atlanta’s Water Supply Program Tunnel project includes a 7,315-m (24,000-ft) long, 4-m (13-ft) diameter, hard rock tunnel. A complex aspect of the project involves connecting five, blind bore shafts to the tunnel in a location close to current drinking water reservoirs. During the supplemental geotechnical investigation following the initial contract award, results from additional borehole geophysics were reviewed. Unfavorably oriented fracture sets forced a change in the original pre-excavation grouting program designed for that site. Real-time grout monitoring and geophysical data were compared to provide assurance that the program, as designed, correlated with the in situ ground conditions. Following grouting, results were modeled, and all grouting data were reviewed to determine if grouting was complete.Project backgroundThe current water supply system operated by the city of Atlanta’s Department of Watershed Management (DWM) consists of four, aged, raw-water pipelines, one of which dates back to 1893. Based on previous assessments completed by the DWM, the entire water supply system is at, or will soon reach, its recommended useful life. As such, the city acquired the Bellwood Quarry in 2006 with the intention to create a water storage facility with a volume of approximately 9.1 billion L (2.4 billion gal) to serve approximately 1.2 million people.The project location is shown in Fig. 1, which is generally in the northwest part of downtown Atlanta, GA. The overall project has been divided into two phases. The Phase 1 project connects the quarry and the Hemphill Water Treatment Plant (HWTP), and the Phase 1 Extension project connects the HWTP to the Chattahoochee Water Treatment Plant (CWTP) and the Chattahoochee River. A 7,315- m (24,000-ft) tunnel with a finished diameter of 3 m (10 ft) connects all three elements. The HWTP location is also where the city’s two most proximate drinking water reservoirs are located."

Jan 9, 2018

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

"It’s been 80 years since Charles Warman invented the iconic Warman slurry pump, a pump that revolutionized the mining industry and continues to push the boundaries of pump performance to this day.In honor of this legendary brand, Weir Minerals hosted an event at the end of May in Kalgoorlie, Western Australia. Throughout the evening, attendees relived Warman pumps’ history and gained an insight into some of the future innovations planned.“It was a privilege to share this special night with some of our key customers, past and present employees, and members of the Western Australian School of Mines,” said Ricardo Garib, divisional president of Weir Minerals. “Warman is one of our leading brands. It has truly shaped the mining industry over the past 80 years and is a product we are all very proud of. The Warman pump, invented to solve high wear issues in slurry pumping, created a thriving industrial business that is now the cornerstone of Weir Minerals with more than 8,000 people, and more than 150 manufacturing and service centers across the globe.”Always inventingCharles Warman invented the Warman slurry pump in Kalgoorlie in 1938. It was a hardwearing slurry pump that used replaceable liners and a replaceable impeller, something that had never been done before.“Charles Warman was a visionary and an innovator. The use of rubber lining in the pump was groundbreaking as it reduced total ownership costs, was safer to handle and offered extended wear life in many abrasive slurry applications. It is a great example of solving customer problems with material science, and is still taught in universities today,” said Marcus Lane, global product manager for centrifugal pumps at Weir Minerals.It was quickly adopted throughout the goldfields in Western Australia and by the 1950s, as customer demand rose, Warman expanded his business by opening offices in Sydney and Perth.During the 1960s the rapid growth of the business continued with manufacturing and sales outlets established around the world. The Warman Series ‘A’ pump was accepted and became a world leader in its field. Further work on the Warman AH pump resulted in the development of interchangeable metal and rubber wearing components."

Jan 9, 2018

By Gary Brierley, Lok Home

"The majority of tunnels for civil engineering applications are now being constructed using some form of mechanical excavation. Beginning in the 1960s with rock tunnel boring machines (TBM), the tunneling industry has introduced both earth pressure balance (EPB) and slurry pressure balance (SPB) soil machines; mixed soil and rock machines and a variety of different mechanical devices for the construction of small diameter tunnels. Over time, these machines have become more powerful and more adaptable to a wider variety of ground conditions; so much so that tunnels are now being constructed in ground conditions and in the vicinity of third-party impacts that would have been considered beyond the state of the art just 10 years ago. Figure 1 is an example of a mixed ground crossover TBM used successfully at Mexico City’s Túnel Emisor Poniente II.All of the above is highly advantageous for the tunneling industry, but it has also placed a much higher level of risk on the performance characteristics of the tunneling machines, on the contractors operating those TBMs and on the manufacturers of those machines. Most of the risks for a tunneling project are associated with creating the space inside of which the finished facility will be constructed. In order to create that space, the tunnel contractor must make many decisions about the best way to excavate the ground, the best way to control the ground at the face of excavation and the preferred method for supporting the ground around the tunnel in a manner that is safe for the workers and stable with respect to all of the overlying and adjacent existing structures. If it is proposed to use some form of TBM in order to build the tunnel, then the TBM becomes central to all three of these activities and becomes an integral part of managing the risks associated with these activities."

Jan 9, 2018

By William Gleason

"The city of Denver, CO has experienced extreme growth in the past decade, with the population of the city topping more than 700,000 people in 2018. The current storm water drainage system was put in place in the early 1900s and has not been able to keep up with the growth of the city.When it rains north and east of the city, the runoff goes toward the South Platte River. With the dense population and sometimes severe thunderstorms in the summer, the city has experienced significant flooding that not only endangers lives of residents, but some of the storms have caused millions of dollars of property damage.The Platte to Park Hill Project is a $298-million nearterm, four-phase solution to the flooding that includes the Globeville landing outfall; an open drainage project in the Cole neighborhood in north Denver; an area for temporary water detention and another temporary water detention in Park Hill.The largest and most complex phase of the project is the Globeville landing outfall — a $70-million box culvert project that includes a pair of 157-m (515-ft) long, 243-cm (96-in.) diameter storm water tunnels that pass beneath a busy rail yard with 17 tracks for the Union Pacific Railroad (UPRR) and two Regional Transportation District (RTD) commuter rail tracks. The tunnels, which were installed parallel to a pair of existing 243-cm (96-in.) tunnels, were designed by Brierley & Associates as a client of Merrick & Company for the City & County of Denver, and Bradshaw Construction constructed the one-pass tunnels.From the start, it was evident that the tunneling portion of the project would be the most challenging because of the rail yards.“It’s a little bit more complicated because the railroads have such tight restrictions for settlement,” said Rebecca Brock, Brierley’s project manager. “We had a lot of meetings with Union Pacific and RTD to figure out what are prescribed versus tolerable settlements.”“The portion extending beyond the UPRR under the RTD rails was challenging, as RTD is new to tunnel installations under its tracks,” said Lester Bradshaw, president of Bradshaw Construction. “The RTD tracks employed a unique foundation of continuous concrete with integral raised concrete ties on rubber bushings. Minimizing settlement to these tracks was a critical requirement.”"

Jan 9, 2018

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018