Search Documents

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By Georgene Renner, Chee Theng, William Gleason

"In February 2018, drawn in part by the states’ proud mining heritage, SME took its Annual Conference & Expo to Minneapolis, MN for the first time. More than 5,000 people and 554 exhibitors converged on the Minneapolis Convention Center for three days of networking, exhibiting and technical sessions.The state’s mining legacy, one that continues today, is fueled in large part by its vast iron ore resources in the northern part of the state. The historical significance of the mines in the Mesabi Range, otherwise known as the Iron Range north of Lake Superior, cannot be understated. “Mining is a way of life here,” said U.S. Congressman Rick Nolan of Minnesota’s 8th Congressional District. A native of the Iron Range, the three-term U.S. congressman was one of the featured speakers of the opening keynote session. “We like to think we contribute enormously to the well-being of this country and the world. We were the source of the iron ore and steel that helped win two world wars. And we like to think that we are part of the progress that has taken place in the United States ever since.” Nolan kicked off the keynote sessionthat focused on innovation and its part in the mining industry. The session included Rene Aquilar, vice president of corporate affairs and sustainability, Antofagasta Minerals Group; Bob Anderson, vice president for research and development, 3M; Rolf Weberg, executive director, Natural Resources Research Institute, University of Minnesota-Duluth and Christopher Beck, executive vice president and president, Nalco Water. The panel session looked at U.S. and global minerals production, and the importance of the United States to maintain a major role in the minerals industry, both as a producer and as a technology leader. The panel also touched on the global mining industry and the issues that impact mining around the world. Sustainability, the use of water in mining and earning a social license to operate were among the topics discussed by the panel.Speaking of the importance of mining, Nolan conceded that talking about the benefits of mining to the crowded auditorium at the SME conference might be akin to a preacher speaking to the choir, but, following the adage that all politics are local, he continued to illustrate his point by emphasizing the importance of mining to the Great Lakes.“A study by Homeland Security concluded that 13 percent of the nation’s GDP comes out of Lake Superior through the locks at Sault Ste. Marie and most of that is iron ore,” said Nolan. “That study found that, if those locks fail, it would create a national depression. It would put millions of people out of work. That ore and those minerals supply the steel mills, the auto industry, the heavy industrials. They are the heart of our economy. The study concluded that if the states that make up the Great Lakes were a nation, it would be the fourth largest economy in the world.”"

Jan 5, 2018

By Ravi Sahu

"In the global mining industry, there are those who seem resigned to the fact that the mining industry has always operated according to certain time-tested principles that don’t involve jumping on every new technological trend. Others expect that mines will soon have autonomous electric vehicles running around the clock. The truth lies somewhere in the middle. In business, as in life, that is usually the best path to follow.The instant access to people and information provided by 21st-century technology continues to push businesses in all industries toward greater efficiency and unheard-of levels of modernization. And in the world of mining, the embrace of advanced technology is all about managing risk.However, even in this age of digital information overload, some mine sites still require employees to physically download data from individual trucks to monitor payload data and inspect road conditions using a clipboard. What’s more baffling is that other mine sites still have no way of tracking tons moved at all.This isn’t due to a lack of innovation in the industry. Quite to the contrary, there is an abundance of new technology available that provides real-time monitoring of vehicle movements and tracks road conditions without the intervention of people. So why are owners reluctant to embrace advances in mining tech?Gauging the value of changeSurvey data has traditionally been captured by ground laser scans and LIDAR systems. A mine site surveyor would drive around the pit with a truck-mounted scanner to generate a point cloud. This process would be completed every few days and would take an entire day.The many cons of this method far outweigh the pros. First, it provides no visual data. If an operation has moved beyond the roller wheel and tape measure, visual pit models and LIDAR scans are typically completed once every six to 12 months by an aerial flyover, but such sporadic information gathering isn’t likely to result in the most actionable data. Moreover, given the high cost (in terms of both money and time), the numerous safety and liability issues, and the lack of flexibility in scheduling, manual processes are more trouble than they are worth.Overall, while miners are excellent operators who value innovation, their employers often try to outsource it or acquire innovators instead of investing in existing technology that can improve current operations. It is a never-ending dilemma:"

Jan 5, 2018

By U. S. Geological Survey Staff

"In 2017, the total estimated value of nonfuel mineral production in the United States increased by 6 percent from 2016 (Table 1). The value of metals produced domestically increased by 12 percent and the value of industrial minerals produced domestically increased by 3 percent. Some metal commodity values (cobalt, magnesium metal and palladium) increased by more than 35 percent in 2017 from 2016 owing to higher prices.Some U.S. metal mines and processing facilities remained idle in 2017, including three primary aluminum smelters in Indiana, Missouri and Washington; a titanium sponge facility in Utah and a byproduct vanadium production facility in Utah. In contrast, new gold mines opened in late 2016 and 2017 in Nevada and South Carolina, respectively, and iron ore mines in Michigan and Minnesota restarted or operated for the full year. In addition, increased oil and natural gas drilling activity led to increased production of some industrial mineral commodities that are used for oil and gas drilling. Production of some industrial minerals, especially those used in infrastructure and residential construction, remained essentially unchanged in 2017, a reflection of the limited growth in construction activity. The production of some metals, including iron and steel, aluminum and other nonferrous metals and nonmetallic mineral products increased. Overall, mining activity trended upward as the result of increases in coal mining, oil and gas extraction and metal mining (Table 2).Discussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

Jan 5, 2018

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By M. W. Buche, E. Tarshizi, R. Chappidi, B. Inti

"Coal mining is an age-old method of power production in the world. It is also widely known for the associated risks during mining. Although the number of mishaps has dropped dramatically over the years, the number of fatal accidents is still a concern, and any aid in reducing these figures would be important to industry workers. Therefore, data from accident reports during the past seven years were collected and analyzed. Qualitative data from reports and articles provide a deeper understanding of the incidents, thus affording the possibility of identifying patterns and relationships between the accidents. For this study, a total of 119 fatality accidents occurring in U.S. coal mining operations were analyzed using advanced text mining techniques. The fatality data were obtained from U.S. Mine Safety and Health Admininstration fatalgram reports. This analysis is primarily exploratory in nature and uses term frequencyinverse document frequency (TF-IDF) methodologies along with correlation network plots. An interesting word relation pattern was obtained that identified “positioning” as the common cause of 12.6 percent of accidents, and found that 29.4 percent of accidents can be categorized as vehicle-related. IntroductionIn the mining industry, accidents are situations that employees and employers wish to avoid. They are devastating experiences to the victims and their coworkers alike. Even worse, accidents that result in fatalities create trauma and undesirable repercussions. Several measures have been taken throughout the industry to prevent such mishaps, and the U.S. Mine Safety and Health Administration (MSHA) provides continuous monitoring for miners’ safety by guiding organizations through best practices in every job role. As a result, according to MSHA, there has been a steady decline in the average number of deaths due to accidents over time. Nonetheless, any opportunity to avert one more such casualty is of paramount importance, and that is the goal of our analysis. Our objective is to identify opportunities resulting from previously unexplored directions in order to provide additional insights into potential safety recommendations. Until now, most of the studies in this area had been conducted using structured and tabulated data with a constant number of categorical and numerical variables. Unstructured text data mining is an emerging area that is still insufficiently researched and has a feasible scope for important results, as a vast majority of human communication and cognizance is comprised of words. The aim of undertaking this project by capitalizing on unstructured data is to analyze the text reports to discover potential relationships that explain the causes of accidents in new light in order to mitigate the occurrence of fatalities. The analysis in this project is based on textual data obtained from the MSHA website (2017). Individual accident reports are organized according to the date and year of the fatality. Each report includes details with images of the incident. For convenience, a simplified summary of the report is also available. Data collection consisted of gathering formal documentation of fatal accidents in the coal mining industry during the past seven years. These reports were extracted from the website in text format."

Jan 4, 2018

By Atta Ur Rehman, Kwame Awuah-Offei

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis in community engagement programs to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This article proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies.The mineral industry provides raw material for industrial activity to support society (Martens and Rattmann, 2001). Mines have changed from conventional mining practices to sustainable ones because of the negative impacts of mining in the past and increased public awareness (Wang et al., 2016). The concept of sustainable mining is getting mature, as stakeholders (e.g., governments, investors and host communities) are getting more involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in the failure to acquire a social license to operate (SLO) (Thomson and Boutilier, 2011). The SLO, if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomson and Boutilier, 2011).Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 4, 2018

By Robert Klug, Nils Engelke

"In order to extract proportionately small quantities of valuable minerals, mining companies move large amounts of earth. A resulting waste product of this process has traditionally been stored in a semi-liquid phase known as tailings, typically stored in a large pond created by an earthen dam at the low end of a drainage basin. It is generally expected that these dams are stable enough to withstand the pressure of the stored material. Unfortunately, history shows us that this is not always the case. The Baia Mare dam in Romania failed in 2000, causing tragic and prolonged environmental damage to several major European rivers. The Bento Rodrigues dam in Brazil failed on Nov. 5, 2015, and that event resulted in the loss of 16 lives.In hard rock mining, many minerals are imbedded within the ore. As part of the mining process, valuable minerals are extracted from the ore; often, the mineral content is only a fraction of the total ore volume processed. To extract the minerals, the ore is typically crushed and pulverized into very fine particles, then wetted to form slurries. The minerals are extracted from the slurries through a series of flotation and/or sedimentation steps with the aid of water-soluble separation chemicals typically known as reagents. Following the mineral extraction, the resulting residual wetted ore cuttings are labeled as tailings. At the end of the extraction process, the tailings are in a thick semi-fluid sludge state, often with trace elements of the extraction reagents.Historically, these tailings are deposited in giant basins or sludge ponds, where they pose a great threat to the environment while binding large volumes of waste process water.Process water recovery and achievingdry tailingsCurrent generation engineering studies, trials and successful field implementation have shown that an alternate process known as dry stacking is practical. The dry stacking process deposits dewatered tailings into containment areas that are smaller in overall footprint and significantly safer by reducing the transfer of reagents into the tailings storage area. In addition to achieving the dry tailing benefits mentioned, it is possible to recover valuable process water while dewatering the tailings sludge utilizing modern separation technology."

Jan 4, 2018

By P. W. Conrad, C. Todd, N. A. Degerstrom, N. West, R. Kramer

"Surface subsidence caused by underground room-and-pillar mining operations and by solution mining operations have been studied separately but never in combination. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Using Salt_Subsid, a subsidence software package from the Solution Mining Research Institute, and ArcGIS, Esri's mapping platform, researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. Project backgroundFMC Minerals has increased the production of trona from its Westvaco Mine near Green River, WY, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 488 m (1,600 ft). Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed.The location from which the trona is removed and the size of the cavern created by the solution mining operations are important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found between surface subsidence measurements and the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find relationships between the measured subsidence and the solution mining activities. The project attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The project attempted to model the relationship between the measured surface subsidence and solution mining production using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI, Clarks Summit, PA) to estimate the location, size and shape of the solution mining cavern. This study would determine the program’s usefulness for locating and developing the cavern created by secondary solution mining activities. The subsidence and production data sets used in this study were collected over a seven-year period from 2008 through 2014."

Jan 4, 2018

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018

By J. -B. C. Varnier, J. A. Cremeens, D. D. Overton

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County in Colorado in the United States were investigated using three-dimensional discrete element modeling methods. Large-scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back-analysis was conducted using prefailure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. IntroductionThe Pikeview Quarry is an aggregate quarry located approximately 8 km (5 miles) northwest of Colorado Springs in El Paso County, CO, USA. The quarry has been operated by several owners since the early 1900s. According to the U.S. Mine Safety and Health Administration (MSHA, 1986), the quarry has been a major source of construction aggregate for the Colorado Springs area for many years. In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy.A large-scale slope failure occurred on Dec. 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on Sept. 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure.The objective of this paper is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry, and both of these mechanisms were given equal credence in the present study. Quarry excavation and backfilling was a key factor in the slope instability for both failure mechanisms. The excavation was backfilled in stages in an effort to provide slope support. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability."

Jan 3, 2018

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

"Tell us how you got involved in mining and about your career path.My dad was a coal miner and my uncle was a metallurgist, so when I enrolled at Penn State’s New Kensington Campus, I chose the College of Earth and Mineral Sciences — exact majors didn’t get picked till the end of your sophomore year. Penn State New Ken had an associate degree in mining program and one of the guys in my carpool was going to take Mining 30 in the evening and the other guy (mechanical engineer) was also able to take an evening class. I didn’t want to break up the carpool, so I took Mining 30, complete with essay tests. I could write, so I did well, and the professor said I should go into mining engineering. Fast forward to the end of the next term at University Park, and I realized there wasn’t enough chemistry in mining. Switching to metallurgy would have meant another term at that point, so Dr. Lovell, my advisor, trotted me down the hall and to the next building and said I was a mineral processor. That stuck. I was a summer student at U.S. Steel Research between my junior and senior year and they paid for my master’s degree — all about clay and macerals in coal flotation. During that time, the steel industry tanked, and I thought a Ph.D. would be a good idea — I could always teach at the university level if I had those credentials. The Electric Power Research Institute had a Coal Cleaning Test Facility in Homer City, PA, and I conducted my Ph.D. research on rate and residence time in conventional coal froth flotation cells there and at a local cleaning plant. I went to work at the test facility in 1987 (later CQ Inc.) and stayed there until I started PrepTech Inc. in 1997. PrepTech offers some consulting services for coal cleaning plants and sells mineral processing equipment, mostly to coal companies. I can’t believe it’s been 21 years.And what about your SME career?Of course, I was a student SME member at Penn State. We used many of the SME books in class, so who wouldn’t want the student discount? While in Homer City, I became involved with the Appalachian Plateau Subsection of the Pittsburgh Section. We’d hold quarterly meetings with interesting speakers and had good attendance. I was the secretary. I’m still the secretary and also get the bank statements. We’ll need to close that out some time, but I guess I’ve been hoping for resurgence in the Indiana/Cambria/ Somerset area."

Jan 3, 2018

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives require an air source to supply breathable air to the occupants. This requires pressure relief valves to prevent unsafe pressures from building up within the refuge alternative. The U.S. Mine Safety and Health Administration (MSHA) mandates that pressure relief valves prevent pressure from exceeding 1.25 kPa (0.18 psi), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. The U.S. National Institute for Occupational Safety and Health (NIOSH) tested a variety of pressure relief valves using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork and various sensors to determine if the subject pressure relief valves meet the MSHA requirement. Relief pressures and flow characteristics, including opening pressure and flow rate, were measured for five different pressure relief valves under a variety of conditions. The subject pressure relief valves included two off-theshelf modified check valves, two check valves used in MSHA-approved built-in-place refuge alternatives, and a commercially available valve that was designed for a steel refuge alternative and is currently being used in some built-in-place refuge alternatives. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.03 to 0.22 psi) and flow rates up to 19.3 m3/ min (683 scfm). As tested, some of the pressure relief valves did not meet the 1.25 kPa (0.18 psi) relief specification.IntroductionThe Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the United States in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement (U.S. Mine Safety and Health Administration, MSHA, 2006). Section 13 of the MINER Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives for underground coal mines. This mandate culminated in the 2009 adoption of changes to Title 30 of the Code of Federal Regulations (30 CFR) mining health and safety regulations, requiring underground coal mines to provide mine emergency refuge alternatives and associated components, to provide a life-sustaining environment for persons trapped underground. Such refuge alternatives can be either self-contained mobile units or built-inplace facilities. The regulatory changes also include provisions establishing requirements for MSHA approval of refuge alternatives and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the refuge alternatives. One specific criterion for maintaining a safe refuge alternative atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi), or at a pressure above mine atmospheric pressure, in the refuge alternative, as specified by the manufacturer when the breathable air is supplied by a fan or compressor (MSHA, 2008)."

Jan 3, 2018

By Emily Dieckman, Claire Kincaid

"When most people think “miner,” they picture an older white man in a dusty shirt and suspenders. He’s holding a gas lamp and a pickaxe, peering at the walls of a dimly lit cavern. This image, while steeped in heritage, is no longer representative of what mining is: a global, increasingly diverse industry.It’s an industry made up of individuals like Zambian-born Chushi Mwewa, PE, president of Southlands Engineering, LLC in the United States and managing director of Southlands Engineering Limited in Zambia; Navajo tribe member Peter Denetclaw, manager of environmental programs and Navajo relations at Freeport-McMoRan; and Chinese and Jewish Alyssa Hom, a project engineer at McCarthy Building Companies.According to the Austrian Federal Ministry of Science, Research and Economics, 168 out of the world’s 195 recognized countries have some mining or mineral resources activity, and the mining industry directly employs more than 25 million people across the globe.However, according to McKinsey & Company’s 2017 “Women in the Workplace” study, white males hold 67 percent of C-Suite positions and 70 percent of senior vice president positions in the corporate world, and mining is no different. This uniformity among leadership has been tied to lower levels of employee engagement, innovation and business growth. The bottom line is this: Diversity is good for business. The question industry leaders must now ask themselves is not “Will we promote diversity?” but “How will we promote diversity efficiently and permanently?”More than 80 industry professionals, consultants and students gathered to discuss this question and share stories at the “Developing Diversity in Mining” workshop organized by the University of Arizona’s Lowell Institute for Mineral Resources (IMR), held during the 2017 SME Arizona Conference in December 2017.Brad Ross, co-director of the IMR and one of the facilitators of the workshop, said he felt diversity was important to discuss because he has witnessed its benefits throughout his career in the mining industry.“By creating a team of people with different experiences and perspectives, a company is better equipped to see the big picture and to creatively tackle problems,” he said. Speakers from industry and academia,including Mwewa, Denetclaw and Hom discussed the challenges surrounding achieving diversity and inclusion as well as the roles and responsibilities of different stakeholders."

Jan 2, 2018