Search Documents

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By J. L. Furtney, C. Fairhurst

"Although global mineral resources are considered to be adequate to meet the needs of a rapidly growing world population, the United States is becoming increasingly dependent on imports. This could have implications for both the economy and national security. The US is a country with a strong tradition of leadership in science and technology. Impressive advances in autonomous underground mining systems reduce the adverse effects of heat and humidity in deep mines and focus renewed attention on ground control. Developments in computing power open opportunities to develop improved understanding of the important role of discontinuities (faults and fracture systems) and more effective design of deep excavations. Establishment of mining R&D Centers at leading US research universities, jointly funded by industry and US federal agencies is recommended as an effective step for the nation to remain an influential partner in world mining. INTRODUCTION. “None of the arts is older than agriculture, but that of metals is no less ancient.. . for no mortal man ever tilled a field without implements. If we remove metals from the service of man, all methods of protecting and sustaining health and more carefully preserving the course of life are done away with.” Agricola (1558)i Homo sapiens, generally acknowledged as the species from which modern Man has evolved, is considered to have originated in Swaziland some 100,000-200,000 years ago. Evidence of use of minerals in that region has been dated to earlier than 40,000 BC.ii Today, a large fraction of the elements of the Periodic Table are derived from minerals, and finding new applications in development of innovative technologies. Agricola’s comments are as applicable today as ever.iii Metals such as copper, tin, lead, iron and aluminum were mined and smelted several thousands of years BC. It was not until the Industrial Revolution, started in the latter half of the 17th Century in Northern England, where coal was available as an energy source, and iron as the basis for fabricating machinery, that dramatic change to society began to occur. Human toil was replaced by far more powerful machines. Rural communities migrated to work in factories in urban areas. Rapid transportation over long distances became possible, leading eventually to the world of today. The change spread to other parts of the world, bringing wealth and power. Although now well established in some regions, the Revolution has still to arrive in many other parts of the world. This can be seen in Figure 1, which shows the relative wealth, or ‘Standard of Living’ as measured by the GDP/capita, of regions around the world. Regions such as North America, Europe, and Australasia iv are seen to have the highest standard. Thanks to today’s global communications systems, regions with relatively low GDP/capita are well aware of ‘how others live’ – and eager to emulate them."

Jan 1, 2018

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

"Longwall shearers are widely employed in underground coal mines. The reliability of such machine has significant importance for successful mining operations. This paper aims at studying reliability of a longwall shearer using failure data recorded for a year. Data was pre-processed, sorted and selected for analysis. Selected data is then examined using statistical models. Distribution fitting of time-between-failure (TBF) and time-to-repair (TTR) are accomplished using three different models. Goodness-of-fit criteria is used to ascertain the best fitting model. Reliability in terms of mean-time-between-failure (MTBF), and mean-time-to-repair (MTTR) are calculated using the model which best represents the failure data. Exponential distribution best represents the time between failure and lognormal distribution the time to repair data. A well-known risk management technique Failure Mode Effect and Criticality Analysis is used to evaluate the critical breakdowns. Critical system/parts, experiencing regular failures is delineated based on this analysis. INTRODUCTION Mining is a capital intensive process, and huge monetary investment is required to develop and operate a mining project. Heavy and expensive equipment’s are employed in development and operation of these projects. In order to ensure timely completion of set milestones, it is mandatory that equipment’s perform their required task productively. Delays are not unusual owing to breakdown of these equipment’s. Breakdown or failure experienced by any of the equipment pose heavy financial burden. Moreover, frequent times, companies have to employ and dedicate additional resources to make up for such delays. Delays in project is not only detrimental to company’s image in market, but it also interrupts customer commitments. Mines having history of not fulfilling their promise usually get lower commodity price. Penalties are also imposed on the companies defaulting its obligations. Especially, in today’s world where competition among the companies are growing, success means keeping up the commitments in a timely manner. Heavy machinery and equipment are instrumental in success of any project. These machinery and equipment’s have to reliable in a sense that they can perform the set task in given time period. Reliability of these equipment plays a pivotal role in success of any project. The reliability analysis of mining equipment has long history. Many researchers have applied different statistical models for analyzing the reliability of mining machines (Samanta, Sarkar [1]. Kumar and Klefsjö [2] demonstrated the use of the power law process model for reliability assessments of repairable mining machines. Barabady and Kumar [3] performed the reliability analysis from failure data of the crushing plants."

Jan 1, 2018

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By T. A. Laser

"INTRODUCTION A positive workplace environmental, health, and safety (EHS) culture affords organizations and corporations many benefits, including increased trust and employee morale, sustainable EHS performance improvements, and reliable productivity and profit margin growth. Unfortunately, many leaders and EHS professionals struggle daily to achieve and maintain positive workplace cultures and consistent business results. While lack of management support, corporate or employee buy-in, resources, and time are common factors that conflict with an EHS culture and safe work behaviors and processes, there are many other actions that threaten the positive attributes of an organization’s culture. Often these culture killers are not recognized, or worse yet, ignored because they are considered taboo. For example, voicing observations or questioning long-held management practices or process that were initially designed to promote EHS values, but no longer do so. Unfortunately, this could be viewed as challenging authority, not being a team player or even not valuing EHS. And for those that speak up, the potential for negative consequences can be real impediments to positive change. Having an open mind, constantly striving to identify culture killers, and putting forth the effort to eliminate them are the first steps to begin reaping the benefits of having a sound workplace culture. This paper helps readers to: • Recognize culture killers that negatively impact fostering and maintaining sustainable EHS cultures in the workplace. • Understand how to prevent, avoid, and respond to culture killers, before they wreak havoc in your organization. • Assess EHS culture strength, and implement plans to continuously improve it. The desire to draw boundaries around concepts, put things into boxes, and nail down requirements for something that is virtually impossible to solidify for any length of time is quite fascinating! These desires can pose challenges when trying to define what the perfect EHS culture should look like. The very act of trying to define our culture tends to create silos, and these silos, in turn, can become “culture killers”. The following is one of the most common culture killers. UNBALANCED ORGANIZATIONS TRIGGER CULTURE KILLERS Unbalanced organizations occur when an organization’s constantly shifting focus forces other important needs to take a back seat--until the focus changes again. This balancing act can be detrimental and lead to catastrophic results including low morale, lack of trust, employee dissatisfaction, high turnover, increased incidents, poor profit margins, loss of market share, and ultimately into organization-wide failure."

Jan 1, 2018

By L. H. Monaco

"The evolutional process is always about solving existent problems in order to provide further achievements. But the more something evolves, the more challenges it faces towards greater evolution. Industrial automation systems in Mining have also evolved a lot in the past decades, but they now face new challenges about integration: how to integrate different locations and systems, in a way to reduce costs and increase overall mine efficiency and safety for the operation. This paper compares conventional mining process automation architectures vs. a state-of-the-art, completely integrated system using Electrical Integration based on IEC 61850 standard for Substation Automation Systems. Emphasis is placed on the benefits to manage the entire mining plant as a whole, not only looking at the production rates, but also at the energy consumption for each part of process. In addition, it is discussed how an integrated system approach unlocks safety and productivity gains such as overall process optimizations, improved operator effectiveness, increased plant availability, and reduced maintenance costs. INTRODUCTION The world is constantly changing, and evolution is a natural part of mankind history. The role of evolutional process is to solve existent problems, but usually these solutions create new issues that need to be addressed. This scenario is also applicable to the industrial environment, in which the demand for higher profitability and efficiency on their processes requires solutions with more productivity using less resource. This is not different when it comes to energy consumption: how to optimize production rates and reduce energy costs at the same time? Regarding automation systems, the trend for the industries is to focus on four main challenges: how to provide safety for personnel; how to reduce initial investment for new plants; how to connect remote and in harsh locations; and above all how to deal with the lack of integration between several systems."

Jan 1, 2018

By O. A. Velasquez, A. R. Kumar

"Continuous miners are often equipped with a flooded-bed dust scrubber to clean the air from close to an active underground coal mining face. However, its impingement screen is prone to clogging due to an accumulation of dust, thereby lowering the scrubber’s efficiency and potentially exposing the mine workers to higher levels of dust. Fans can compensate for the increased resistance by varying their operating parameters, but the scrubber screen needs significant maintenance which leads to downtime. The authors have proposed a suitably sized Vortecone as an alternative to the conventional flooded-bed dust scrubber system. Water is used as the filter medium, which is replaced and recycled continuously. Preliminary CFD investigations of Vortecone scrubbers have indicated higher cleaning efficacies, especially in the respirable range. This paper presents the results including the flow characteristics and capture efficacies of a full-scale Vortecone. Multi-phase flows, including free-surface modeling and particle tracking methods, have been adopted. ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research project. This research is being developed with the support of a NIOSH Grant 200-2014-59922- ‘Coal Mine Dust Mitigation through Novel Scrubber Development and Numerical Modeling’. The views expressed in this paper are those of the authors and do not necessarily reflect those of NIOSH. This project is aimed at designing novel and efficient scrubbing systems for underground mining operations. The authors acknowledge Dr. Thomas Novak of the Department of Mining Engineering, the University of Kentucky for his support and encouragement. The authors also thank Dr. Sunil Vytala, CFD engineer at Cradle CFD for his invaluable inputs to the numerical models.INTRODUCTION Continuous miners are the main production machines deployed in room and pillar mining operations. These miners extract coal by the shearing action of the wethead cutting drums. Strategically placed water sprays on the drum not only cool the bits extending their useful service life, they also suppress the dust at the point of generation itself. A flooded-bed dust-scrubber (Campbell, et al. 1983) is usually integrated onto the continuous miner to arrest dust from close to the active face. These fan-powered scrubbers have an impingement screen flooded with water, which also serves as the filter element. A demister downstream of the screen removes the excess water from the air cleaned. These conventional scrubbers have been found to be very effective in alleviation of respirable dust levels underground (Chao and De-sheng 2000) (Colinet, Reed and Potts 2013). However, the inefficiencies of the flooded-bed dust scrubbers arise out of their internal components. Depending on the mining conditions, the screen may be clogged by the accumulation of the trapped dust particles. The resistance of the scrubber system is increased reducing the airflow. The flooded-bed dust-scrubber system would, therefore, require frequent maintenance of the screen and the demister (Listak 2010). Since any maintenance needs to be carried out under supported roof, this leads to loss of availability of the equipment as well. In addition to this, the continuous miner operators could be exposed to elevated levels of dust when satisfactory airflow at the face is not achieved."

Jan 1, 2018