Search Documents

By Chonghe Li, Pengyue Gao, Xionggang Lu, Juyun Kang, Wajid Ali, Guangyao Chen, Ziwei Qin

A refractory U–Mo associated ore containing jordisite which enclose U, Mo component, and impede penetration, diffusion process of leaching, oxidation agent was investigated through three approaches of focusing on U, Mo extraction. The results indicate flotation beneficiation without followed metallurgical process is not appropriate because of high target metals loss rate via water leaching. H2SO4, H2O2 dosage recommended to oxidation leaching are 10 and 6–8% of ore mass, and U, Mo leaching rate are 92.71 and 52.16% respectively. For the acid pressure leaching, U, Mo leaching rate 93.75 and 76.07% are achieved under optimal temperature 130–140 °C and H2O2 dosage 8% combined with pressure air 0.6 MPa. Fluidized bed furnace roasting parameters include air flow rate 0.64 m/s, air ore ratio 0.3 m 3/kg at roasting temperature 550 °C with U, Mo leaching rate 93.2 and 89.5%, so enhanced metallurgical process effectively destroy wrapper and increase metal recovery rate.

Mar 1, 2018

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Wufeng Jiang, Jiann-Yang Hwang, Suju Hao, Yuzhu Zhang

Magnetite powder and coke powder were used as experimental materials and H2 as reducing agent in a high temperature vacuum tube furnace. The change rules of magnetite powder (MP), mixed coke powder and magnetite powder (MCMP), and carbon coated magnetite powder (CCMP) in the process of reduction were studied. The samples were determined by field emission scanning electron microscopy and X-ray diffraction. The results show that, with the increase of reduction time, the reduction degree of magnetite powder is improved. Under the same reduction conditions, the addition of coke powder improves the reduction rate. Compared with MP, when the reduction time was 120 min, the reduction degree of MCMP was 30% greater; and the reduction degree of CCMP was 39% greater. The mixed grinding of magnetite powder and coke powder is a better way to add carbon. Under the same reduction conditions, compared with MCMP, the reduction degree of CCMP was 9% greater when the reduction time was 120 min. After the reduction of CCMP, the number of pores in the sample increased and the structure was loose. The results of this study have some reference value for improving the reduction rate of magnetite powder.

Mar 1, 2018

By Sheikh Abdul Rezan, M. N. Ahmad Fauzi, Yong Jing Hui, NORLIA BAHARUN, Noor Izah Shoparwe, Srimala Sreekantan

In this paper, the effect of carbon reductant on carbothermal reduction and nitridation of copper-doped titanium oxide (Cu–TiO ) was investigated.

Mar 1, 2017

By H. Tan

?Preg-robbing? is the active adsorption of gold from cyanide solution by the ore components. The role of carbonaceous coatings on chalcopyrite surfaces in the preg-robbing of chalcopyrite has been investigated by using pure chalcopyrite and a copper concentrate. Activated carbon and graphite were chosen as representative carbonaceous contaminants. It was found that the carbonaceous coatings enhanced the preg-robbing of chalcopyrite. Activated carbon coating increased gold adsorption onto chalcopyrite to a lager extent, in comparison with graphite coating. In the preg-robbing of the copper concentrate, gold adsorption was increased to larger extent at finer particle sizes and at higher contents of activated carbon or graphite. The preg-robbing of chalcopyrite was reduced or eliminated, depending on the concentrations of free cyanide. However, the gold adsorption on the carbon and graphite coated chalcopyrite could not be avoided even at higher cyanide concentrations, and this adsorption was solely attributed to the carbonaceous coatings. Zeta potential studies indicated that the carbonaceous coatings reduced the negativity of the chalcopyrite surface charge. As shown by SEM analysis, gold not only accumulated at the edges and defect sites, but was also spotted on the smooth surfaces of chalcopyrite with carbon or graphite present. XPS results revealed that gold was strongly reduced on chalcopyrite surfaces, with the sulfide ions of the chalcopyrite being oxidized to elemental sulfur. Diagnostic elution indicated three mechanisms contributing to gold take-up by chalcopyrite, i.e. gold reduction, physical adsorption and chemical adsorption.

Jan 1, 2003

By Moo Eob Choi

A new process for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium sulfide and calcium sulfate without generating secondary pollutants was developed at the University of Utah. In this process, sulfur dioxide is reacted with calcium sulfide to produce elemental sulfur and calcium sulfate. The latter is reduced by hydrogen to regenerate calcium sulfide. In the present work, the effects of different pelletization conditions for the initial reactant calcium sulfate on the strength and reactivity of the pellets were determined. These conditions include the type, amount, and impregnation method of catalyst, binder amount, and sintering. Experiments were also performed to determine the effects of temperature in the range of 973-1173 K, pellet size, cycle repetition, and water vapor or carbon dioxide content in sulfur dioxide stream on the reaction rates of the cyclic process. Nickel-catalyzed fired pellets produced by the use of molasses or cement as a binder showed good reactivity as well as high compressive strength during the cyclic tests. The binder amount did not significantly affect the reaction rate.

Jan 1, 2006

By Xiang-ning Meng, Miao-yong Zhu

"A three-dimensional finite-element heat-transfer model is conducted to predict temperature of hot copper plate in a slab continuous casting mold and the effect of casting speed on temperature difference between copper plate and solidifying shell is simulated in combination with process data. The results show that centre temperature of hot copper surface at casting speed 1.8 m·min-1 and 2.0 m·min-1 are higher than that of 1.6 m·min-1 casting speed 4.7-5.2 °C and 11.2-12.2 °C respectively and temperature is not increased linearly with casting speed. Temperature difference in meniscus between mold and shell is influenced obviously by casting speed and increased 4.0- 6.0 °C with increment of casting speed 0.2 m·min-1• Fluctuation of temperature difference in meniscus is a main reason to deteriorate casting quality as increasing casting speed.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipates in primary cooling zone and mold becomes a critical component of caster to govern steel quality, meanwhile, thermal load on mold is increased constantly and environment is also more abominable since high productivity and quality are required and high-effective technologies are applied. So, an in-depth understanding of thermal behavior of mold at high casting speed is essential to design cooling structure and maintain casting stability. Many studies have been carried out to shed light on thermal behavior in mold. Chow et al. [l] applied a mathematical model to heat transfer in billet mold at a high casting speed to give a new taper in order to minimize mold-strand interaction. Thomas et al. [2] researched relation between mold geometry and temperature distribution based on a finite-element heat-transfer model. Lu et al. [3] indicated that slab mold temperature are mainly affected by thickness of copper plate and nickel layer by a heat transfer model. Samarasekera et al. [4, 5] researched temperature of copper plates for both billet and slab molds and effect of a large number of factors ranging from water quality to casting speed. Park and Thomas et al. [6, 7] developed a finite-element thermal-stress model to determine temperature and thermal distortion and stress in both thin and slab molds and O'Connor et al. [8] applied an elastic-plastic-creep finite-element model in a funnel shaped mold to achieve same goals. Cicutti et al. [9] evaluated heat transfer and temperature fluctuation in a slab mold and proposed an expression to predict global heat flux as a function of process parameters and an index to quantify thermal instability. All mentioned above shown that thermal behavior is not only important to casting stability, it is also premise to further understand mechanical behavior in mold."

Jan 1, 2011

By Gowda H. S. Desai, A. Herbert Mervin, P. G. Mukunda

"The mechanical properties of cast iron depend on the graphite morphology and characteristics of metallic matrix. In spheroidal graphite iron these properties are affected by the nodule count, nodule percentage, nodularity, nodules per square mm, nodule types and size distribution. In this work an attempt is made to study of the effect of centrifugal and gravity casting process on the morphology and mechanical properties. A comparison of microstructure and mechanical properties of specimens of the cast are studied. It has been observed that the centrifugal effect produces an increase in rupture strain but hardness is unaffected. In microstructure it has been observed that the centrifugal effect produces an increase in the number of bigger nodules and decrease in the number of smaller nodules and an increase of nodules per square mm. It has no effect on nodularity percentage. The centrifugal casting process produces better mechanical properties.IntroductionCast iron, the first man-made composite, is at least 2500 years old. It remains the most important casting material, with over 70% of the total world tonnage [1,7]. The main reasons for cast irons longevity are its wide range of mechanical and physical properties coupled with its competitive price [l]. Gray cast iron is traditionally used in many industries because it is characterized by a flexibility of use, excellent castability, low cost, wide range of achievable mechanical properties. Gray cast irons are selected according to their tensile strength, high modulus of elasticity, good wear resistance and good machinability are desired and for this a high-strength cast iron is selected [2].Flake Graphite and Spheroidal Graphite irons are predominantly being used to manufacture heavy automobile components throughout the world. The properties of gray iron castings are much dependent on foundry practice. Perhaps the most interesting feature of the family of cast irons is the morphology of the graphite phase, which occurs as a result of changes in chemical composition, melting, melt handling techniques and the process of solidification and subsequent cooling. The significance of these differences through graphite morphology is observed primarily in their effect on the physical and mechanical properties of the iron, but in the foundries these are also known to influence the ability to manufacture sound and dependable castings."

Jan 1, 2013

By Sheng-ping He, Ya-bing Zhang, Qian Wang, Kun-peng Xu

A mass of Al2O3 tends to form during the continuous casting process of high manganese high aluminum steel, and the properties of mould flux and the quality of slab are seriously affected. The dissolution rate of Al2O3 into the CaO–SiO2–MgO–Al2O3–F−−Na2O−Li2O−BaO−B2O3 slag system has been investigated at 1573 K by employing rotating cylinder method. This paper focuses on the effect of Na2O, Li2O, B2O3, F−, Al2O3 contents and (CaO+BaO)/(Al2O3+SiO2) ratio on the dissolution rate. Experimental results show that the dissolution rate increases with increasing Na2O, Li2O, B2O3 contents and decreasing Al2O3 content, among which Li2O has the greatest effect on increasing dissolution rate; the dissolution rate increases with increasing F− content in slag A-1, but decreases with that in slag A-2; the dissolution rate increases with (CaO+BaO)/(Al2O3+SiO2) ratio within the range from 0.91 to 1.31. The dissolution rate of Al2O3 into molten flux is mainly affected by the viscosity of the molten flux and the thermodynamic driving force.

Mar 1, 2018

The presence of clay adversely affects the floatability of copper and molybdenum during processing porphyry copper/molybdenum ores. In addition, reagent consumptions are much higher than when treating clay-free ores. Ores containing kaoline, brammollite, illite and montmorillonite were examined in the laboratory to determine how clay minerals affect the floatability of copper and molybdenum, and to find a possible solution to alleviate the harmful effect of clay slimes. It was demonstrated that the presence of clay mostly affects floatability of coarse and middling particles, and reduces selectivity. The results of the research work showed that there may be several possible ways of reducing the detrimental affects of clay slimes on flotation, some of which include a) use of alternative flowsheets, b) flotation at reduced pulp density, and c) the use of special frothers. The applicability of the findings in plant practice are discussed.

Jan 1, 1999

By C. E. Abbey, M. S. Moats

It is well known that the addition of cobalt to copper sulfate — sulfuric acid electrolytes decreases the overpotential for oxygen evolution and decreases the rate of corrosion of Pb–Ca–Sn anodes. This effect, however, has not been ade- quately quanti fied in the presence of iron and manganese in this type of electrolyte. This work provides quanti fiable data on the effect of cobalt concentration in the range of 0 –0.6 g/L in synthetic electrowinning electrolytes with and without the presence of iron. The effect of cobalt on anode potential was determined using 2 and 24 h chronopotentiometry experiments. As expected, Pb–Ca–Sn potentials increased with decreasing cobalt concentration over the range of 0–0.6 g/L Co with and without the presence of Fe. Two regression models were developed to allow plant operations the ability to predict anode potentials as a function of cobalt concentration with or without iron in the electrolyte.

Mar 1, 2017

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to 'low-Cu-grade' FeS2-CuFeSz concentrates. Chapter 14 does the same with 'high-Cu-grade' CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By Andrzej Warczok

Intensive smelting of copper concentrate in Teniente Converter (CT) leads to the production of high grade matte and highly oxidized slag. Smelting slag is processed in Teniente vascular slag cleaning furnace. The slag composition and forms of copper affect the slag cleaning process and final copper content. Converting of high grade matte in Pierce-Smith converter faces some difficulties in proper slagging of iron oxides. Overblowing in copper making stage allows for slag liquidation but leads to high content of copper oxide in converter slag. Converter slag recycling into CT results in the increase of the participation of oxidic copper. Separate treatment of converter slag and its impact on the forms of copper in CT slag has been analyzed. Thermodynamic properties of a system and kinetic limitations pointed out the negative effect of converter slag recycling on the forms of copper and copper recovery in slag cleaning stage. Experimental results of slag cleaning tests in a crucible scale as well as microscopic examination of laboratory and industrial slag samples supported the above analysis and permitted to formulate recommendations of separate processing of converter slag. Keywords: copper, losses, slag, recycling

Jan 1, 2001

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013