Search Documents

By Jian Li, J. Miles, P. Liu, W. Cook, W. Zheng, Alvin Qian

"High temperature corrosion resistance is one of the key challenges in water-cooled nuclear reactor material development. Iron based materials with low Cr content exhibits superior high temperature mechanical properties. However, due to the relatively low Cr content, their corrosion resistances under supercritical water (SCW) conditions are generally poor. High-Cr alloys, despite their much improved corrosion resistance, often suffer from embitterment due to the precipitation of sigma phase in the microstructure. In this study, corrosion resistance of an in-house produced high Cr steel (25%Cr) showed much better corrosion resistance compared to that of low Cr alloy (14%Cr). This high-Cr steel can potentially be used as a corrosion-resistant coating for structural materials in sew applications.INTRODUCTIONThe supercritical water-cooled reactor (SCWR) concept is one of the promising designs for the next generation nuclear reactor, in which the water coolant is designed to be at about 625°C and 25 MPa at the outlet of the reactor core. Under these relatively high-temperature and high-pressure conditions, the cooling water is at supercritical state. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR in-core conditions. Canada supports research in several key areas of SCWR development, including materials selection. A major focus is on materials development, selection and evaluation for both in-core and out-of-core components.Allen et. al. [1] carried out a comprehensive study on the SCW corrosion resistance up to 600 °C on commercially available high temperature materials including Ni-based super alloys, various types of stainless steels and ferritic/matensitic steels. They concluded that ferritic steels develop a relatively thick but mechanically stable oxide layer, while austenitic alloys develop a thinner oxide layer that has been found to spall in some cases. Of the three types of alloys examined, the Ni-based alloys exhibited the lowest oxide thickness, however pitting was observed in the vicinity of intermetallic precipitates."

Jan 1, 2011

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By Liangying Wen, Zhehan Liao, Jian Xu, Chenguang Bai, Chengfeng Sun, Kaihui Ma, Yang Xu

The difference on particle density causes mass and size segregation in the blast furnace throat, causing poor permeability in radial and circumferential direction. Understanding the effect of density difference on particle spatial-temporal distribution helps stabilize smooth operation and improve energy ef ficiency of blast furnace iron-making process. Based on discrete element method simulation, the influence of density difference on particle segregation behaviors is quantitatively characterized by the proposed method when the binary-sized particles are charged from parallel-type hopper of blast furnace. The results show that increasing the 4 mm particle density aggravates the mass segregation in circumferential and radial direction, and the maximum standard deviation of each ring reaches as great as 0.415. For size segregation, the difference on average mass fraction of small particle between center and edge ring decreases from 0.373 to 0.301. When increasing the 6 mm particle density, the similar particle segregation behaviors could be obtained.

Mar 1, 2018

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Ehsan Vahidi, Fereshteh Rashchi, Ataollah Babakhani, Alireza Zakeri

"The synergistic effect of Cyanex 302 on solvent extraction of nickel and cadmium from sulfate solution with D2EHPA diluted in kerosene was investigated with the aim of increasing separation efficiency. Experiments were carried out within a pH range of 0.1-5.0 using sole D2EHPA and D2EHPA-Cyanex 302 mixtures in different ratios. Increasing Cyanex 302 to D2EHPA ratios in the organic phase caused a left shifting of the extraction isotherm of cadmium and a right shifting of the extraction isotherm of nickel. As a result, optimum separation was found with a Cyanex 302 to D2EHPA ratio of 0.1M:0.5M. In the present system, effect of a modifying reagent such as TBP was studied. The influence of various diluents including kerosene and carbon tetrachloride was also investigated.IntroductionBatteries are popular sources of portable energy. Ni-Cd batteries are manufactured in two main groups of small domestic cells and large industrial batteries with 80% being in domestic use. Ni-Cd cells have various uses, for example in cordless electric utensils, cordless telephones, airplane engine starters, and communicational distribution systems [1].Depleted Ni-Cd batteries are classified as hazardous waste since nickel and cadmium are heavy metals and suspected carcinogens. Given the risk associated with uncontrolled disposal, directions for issuing legislation on disposal and recycling of used batteries have been made in industrialized countries [2]. Recycling of Ni-Cd batteries is important from both economic and environmental points of view. Different methods have been used for recycling these wastes through pyrometallurgy [3], biotechnology [4,5], and hydrometallurgy [1,2].Due to the advantages of hydrometallurgical processes, several studies have been implemented on leaching and solvent extraction (SX) of the used Ni-Cd batteries. Leaching of batteries is usually done in sulfate or chloride media; while solvent extraction has been used in different extractants: two-stage solvent extraction by D2EHPA and Cyanex 272 [6]. Solvent extraction of Cd from leach solutions has been studied using various extractants; Cyanex 301 [1], D2EHPA [7], Cyanex 302 [8], Cyanex 923 [9], Cyanex 272, Tops 99, PC88A [10]. Application of phosphorus based extractants for the solvent extraction studies of Ni such as TOPS 99 [11], D2EHPA [12], Cyanex 272 [2], has been investigated. Separation of Cd(ll), Ni(II), and Co(ll) from chloride leach liquor of spent batteries [13], were explored in the earlier studies. Cd extraction with D2EHPA involves co-extraction of both Ni and Co [14], which causes issues in the separation process efficiency."

Jan 1, 2012

By Rina Kim

There are many factors which affect the gold cyanidation mechanism— mineral composition, free cyanide and dissolved oxygen (DO) concentrations, heavy metal additions, etc. This study combines electrochemistry and surface analysis methods to examine the effectiveness of the above factors on gold cyanidation process. Three gold ore samples were used in this study. Sample 1 was a pyrite concentrate, contained mercury and silver. Sample 2 also contained sulfide minerals, including galena. Sample 3 contained pyrite with sphalerite and galena. In the case of samples 1 and 2, the presence of heavy metals enhanced gold cyanidation kinetics, though the addition of higher DO was not effective on improving the kinetics. Sample 3 showed an opposite behavior: the kinetics was not enhanced by galena, because of its relatively small amount, however, the use of higher DO made improvement in the gold leaching kinetics, likely caused by iron species generated by pyrite oxidation.

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By Andrzej Warczok

Liquid slags produced in smelting of copper concentrates contain copper in a dissolved form as well as mechanically entrained inclusions of copper matte. Coalescence and sedimentation of inclusions during slag cleaning plays a key role in copper recovery. Liquid matte inclusion in a molten slag presents a system of metallic conductor in an ionic solution. Constant electric field induces migration of the matte droplet along the current lines. Additional phenomena occur in a system under crossed electric and magnetic fields. Electromagnetic buoyancy force acting on the inclusion affects its settling rate. Electromagnetic buoyancy force of insulating and metal spheres has been measured in a liquid synthetic slag. It was found that depolarisation of the metal sphere, related to the electrode reactions occurring in the surface, plays an important role in the determination of the direction and magnitude of the electromagnetic force. On the basis of the existing theories and results of measurements a mathematical model describing the behaviour of metallic inclusions in the liquid slag under the influence of crossed electric and magnetic fields was developed. Simulation of behaviour of copper matte inclusions under crossed fields showed trajectory of motion in a liquid slag as a function of the slag properties and the inclusion size.

Jan 1, 2003

By D. Pradhan, R. G. Reddy

"Electrorefining of aluminum scrap was investigated from AlCl3 –1-Ethyl-3-methyl-imidazolium chloride (EMIC) (Molar ratio 1.65) chloroaluminate electrolyte using copper cathodes at temperature of 90±3°C and cell voltage of 1.5 V. The deposits were characterized using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The study was focused to determine the effect of electrode surface modification as well as deposition time on dendritic depositions of aluminum. Their effect on current density was investigated also. It was shown that the surface modification of electrodes reduced the dendritic depositions of aluminum. Pure aluminum (>99%) was deposited for all experiments with the current efficiency of 94-97%. The use of ionic liquids not only reduced the energy consumption but also minimized pollutant emissions (CO, CO2 etc.) compared to the commercial high temperature aluminum production.1. IntroductionAluminum electrorefining/recycling from aluminum scrap using ionic liquid electrolyte is an attractive process today because of the unique chemical and physical properties such as wide temperature range for the liquid phase, high thermal stability, negligible vapor pressure, low melting point and wide electrochemical window. But in conventional practice, melting of aluminum scrap and high temperature molten salt electrolysis makes this process more expensive and less energy intensive (average 13 kWh/ kilogram of aluminum) [1] . Although recycling scrap aluminum requires only 5% of the energy used to make new aluminum [1-2], but the green house emissions like CO2, CO and HF have to be counted for environmental reason. Approximately, 5.31 kilogram of CO2 emitted per kilogram of aluminum production in most of the US industries."

Jan 1, 2009

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000

By Jilai Xue, Shuming Huang, Zengie Wang

The corrosion behaviors of chrome corundum/magnesia in laterite nickel slag were investigated by static crucible method. The results show that the molten slag can penetrate into chrome corundum or magnesia which are used as lining materials in smelter furnace, and the corrosion can occur at the slag-refractory interface and the inner area of the refractories as well. Both the penetrated amount of slag and the penetration depth of Fe, Si increase with increasing FeO content (10–25 wt%) in slag. Such penetration in magnesia is stronger than that in chrome corundum under the same corrosion conditions, as more pores in magnesia may provide channels for slag penetration and corrosion product transportation. A damage of the refractory linings and short service life of smelter furnace may happen during metallurgical processing slag with high FeO content.

Mar 1, 2017

By Yue Yu, Hangyu Zhu, Jianli Li, Di Wang

Thestainlesssteelslagastheby-productofsteel-makingplantscontains 2–10 wt% Cr O , and the potential elution of hexavalent chromium impedes the 2 3 utilization as a secondary resource. The reduction of chromium oxide in steel- making slag containing Cr O by FeSi at 1550 °C was investigated in the labora- 2 3 tory. The experiments were performed in a carbon-tube furnace, and the samples collected during tests were analyzed using X Ray Fluorescence (XRF) and Scanning Electron Microscope (SEM) equipped Energy Dispersive Spectroscopy (EDS). The results show that the FeSi addition could efficiently enhance the reductionandrecoveryofchromium.WhentheamountofFeSirangedfrom2upto 9 wt%,therecoveryincreasedfrom65.60%to84.19%.Theoccurrenceofresidual chromium was metal particles, which dispersedly distributed in silicate phases owing to the size limitation. The sufficient FeSi could easily reduce chromium oxidesintometal,butthecriticalfactorofchromiumrecoveryistheprecipitationof suspending metal particles from the molten slag. Thus, some measures should be proposed in order to make sure that the suspending particles are adequate to aggregate into bigger ones. (cid:1) (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Xiang Lan

A strain of Thiobacillus ferruuxidans No. 8 was isolated from the acidic mine water of an arsenopyrite deposit, South China. It has been found from the experimental results that the growth of bacteria was inhibited by flotation agents. The order of toxic effect of different flotation agents on the growth of Thiobacillus ferrooxidans is ethyl xanthate > butyat ammonium aerofloat > butyl xanthate ? isobutyt xauthate >? flother No. 2 oil. The bioteaching treatment of arsenic and antimony-bearing gold concentrate in Longshan mine, Hunan province, China, was influenced considerably by the presence of flotation agents. The possible causes of the influence of flotation agents were discussed and an improved method was suggested.

Jan 1, 1991

By Isadora Dias Perez, Denise C. Romano Espinosa, Flávia P. Cianga Silvas, Jorge A. Soares Tenório, Mónica M. Jiménez Correa

In view of the rising generation of wastewater containing metals, sustainable and clean techniques to recover them are being researched. This study investigated the adsorption of aluminum, cobalt, chromium, copper, iron (III), magnesium, manganese, nickel and zinc presents in a synthetic ef fluent by chelating ion exchange resin Dowex XUS43605. The resin was tested in columns experiments and was analyzed the flow rate (0.45, 0.66 and 1.11 BV/h), at pH 1.5 and 20 °C. After loading the column, the elution experiments occurred with 1 M of H2SO4 and 4 M of NH4O. The concentration of the metals in solution was obtained by X-ray fluorescence spectrometry energy dispersive (EDX). The results showed that the breakthrough experimental curves demonstrated that the main metals (aluminum, cobalt, manganese and zinc) were immediately broken through just after the initiation of the feeding, while the breakthrough of copper began later. Therefore, the study showed that the chelating resin could be used to treat contaminated effluents with metals.

Mar 1, 2017

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999