Search Documents

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997

By M. Cloete, C. MacLagan, A. Newall

This paper initially gives a brief overview of Zinc Corporation of South Africa Limited (Zincor). The original design parameters of the Zincor roasters are compared to the current operation, and the requirements for efficient roasting are listed. Roaster operational problems experienced during the early to mid 1990's are outlined. A description of the investigation and the outcome to increase overall roaster availability are given. The history and the development of the use of oxygen at the Zincor roaster operation, with an account of the associated operational experiences, are explained.

Jan 1, 2000

By G. S. Victorovich

Technical progress in primary smelting has changed the face of the copper industry in the years since the Second World War. Much of this change has resulted from a wide acceptance of flash smelting technology. In addition, research has been directed toward devising converting processes to replace conventional Peirce-Smith converting technology. One major thrust has involved a revival of the old " ", idea of oxygen flash converting of comminuted mattes. This paper reviews the 60-year history of flash converting. Particular attention is paid to Inco's investigations into the processing of white metal containing significant amounts of nickel and, in some cases, iron. Thermodynamic analysis and laboratory experimental results are presented which throw light on the behaviour of nickel and other salient features of flash converting. The possible role of oxygen flash converting in the copper pyrometallurgy of the future is briefly discussed vis-a-vis direct production of copper.

Jan 1, 1993

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation' of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983

By Robert D. Pehlke

"The evolution of oxygen steelmaking is reviewed and new operating processes are described. The developments which could impact this technology are summarized. Staged and continuous steelmaking are considered in the light of new technologies. The future opportunities for oxygen steelmaking processes are overviewed. IntroductionThe use of oxygen in steelmaking was originally brought on the scene by the development of pneumatic steelmaking. Sir Henry Bessemer in England originally conceptualized the use of gaseous oxygen in steelmaking, and then he and William Kelly in Eddyville, Kentucky independently developed the original pneumatic process which involved blowing air through a bath of molten pig iron to oxidize the carbon and silicon and produce steel. This process and many following processes, including those which would use pure oxygen gas, have been proposed.Beginning with the first commercial oxygen steelmaking vessels at Linz, Austria in 1952, the world steelmaking industry has adopted this style of processing. In general, the process has involved the use of steel scrap in amounts from 20 to 35% of the metallic charge with molten pig iron produced in blast furnaces making up the remainder. The impurities in the charge are oxidized through the use of oxygen gas injected into the steelmaking vessel.However, currently being adopted into commerical practice and on the horizon are a number of advances in this process which include the use of iron ores as a source of iron and oxygen, the use of an all scrap charge, incorporation of pre-reduced iron, the use of auxillary fuels to change the balance of cold and liquid iron-base charge materials and numerous refining techniques."

Jan 1, 1988

By V. M. Paretsky

Oxygen-flame converting of a solid ground matte containing heavy non-ferrous metals in a wide range of concentrations is one of the perspective trends meeting the demands of modern non-ferrous metallurgy. As. a result, of semicommercial tests on oxygen-flame smelting of nickel matte containing 13,5-17,5% Ni; 0,45-0,65% Co under continuous autogenous conditions a converter matte containing 68 8-75,0% Ni and 0,48-1-,0% Co and ferrite -calcium slag containing 1,4-8,4 Ni and 0,16-0,56 Co were pro¬duced. Nickel recovery in a converter-matte was 76,2%, copper - 58,'2% and cobalt recovery in. a slag was 90%. Slag cleaning in an electric furnace allowed to after-recover nickel and cobalt in an alloy to produce a dumpy slag containing 0,03% Ni and 0,02% Co. The development of modern' ecologically pure energy-saving autogenous technologies of the treatment of sulphide raw materials containing heavy non-ferrous metals makes certain demands of the perfection of a process of converting rich sulphide-metallic intermediate products obtained at autogenous smelting. These-demands were connected first of all with the fact that converting process stages because of process periodicity are more unfavourable from the point of ecology, power intensity and unit stability. Besides, during rich matte treatment the problems connected with heat shortage when using air blast and heat excess-when using top oxygen blast to treat luquid matte a-rise and when enriching air blast by oxygen up to 26% fast erosion of the brickwork of a tuyere zone takes place. The technology of Outokumpu and Kennecott companies-on solid- copper matte converting in a flash smelting furnace using air blast is not universal as its possibilities are limited by certain composition of mattes. Besides, flash smelting to produce highly basic or combined slags requires larger enrichment-of blast by oxygen or extra fuel feed. Naturally a flowsheet with continuous converting of matte of various composition up to white matte production is simple,

Jan 1, 1993

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Oxygen-rich side blow bath smelting (OSBS) technology was developed in 2000 based on Vanyukov process. This technology exceeds the traditional pyrometallurgical methods by its great processing capability, high metal recovery and environmental-friendly property. In the past 15 years, OSBS technology extended its application area from lead industry to bismuth, antimony and waste recycling industries, etc. This paper introduces the history and new developments of OSBS technology. The typical industrial applications examples of the OSBS technology in China, including high lead slag reduction, low grade bismuth-lead concentrate smelting and metallurgical waste recycling, are reviewed. Especially, the unique furnace properties and technical parameters are compared. Finally, the potential research directions of OSBS technology are summarized.

Jan 1, 2016

By I. D. Reznik

On blowing nickel matte in a converter without quartz, first the oxidation of metallic iron and a part of FeS occurs without evolving sulfur dioxide, the formed FeO dissolves in a sulphide smelt and form a homogeneous oxysulphide smelt. On further increasing the FeO content, the oxysulphide separates into 2 layers. Based on the laboratory investigation of FeO-(FeS+Fe°) - (Ni3S2+Ni°) ternary phase diagram we have identified the separation region at 1250°C. The boundaries of the separation region have the form of an arc and the composition of the separated oxysulphide layers is defined by the canodes. In the nickel or copper-nickel matte - silicacalcium oxide slag system at 1250°C three layers, namely sulphide, oxysulphide, and slag may be formed. A high slag basicity due to the presence of CaO can serve to enhance the activity of FeO; a low nickel content in the matte corresponds to a high concentration of FeS therein; FeO from slag and FeS from the matte form a homogeneous FeO-FeS solution, i.e. an oxysulphide layer. The investigation on the "Camebaks" apparatus and by the nuclear gamma-ray resonance spectroscopy method of the phase composition in a slowly cooled oxysulphide layer has shown the presence of four phases: wustite, troilite, ferronickel grains, and calcium oxide-silica inclusions. Knowledge of regularities in the oxysulphides formation makes it possible to use them in pyrometallurgy of nickel and cobalt or preventing their formation.

Jan 1, 1997

By Farouk T. Awadalla

The presence of humic species in spent Bayer liquor causes many processing problems in the production of aluminum hydroxide. Ozonation of spent Bayer liquor was found to be an effective process to destroy the colored humic species. The kinetics of the decolorization in spent Bayer liquor was found to be slower than in the alkaline humic acid solution containing no alumina. However, the reaction kinetics ware enhanced by heating the solution during ozonation above room temperature. Copper ions which are used as catalyst to enhance the ozonation reaction were found to be ineffective due to the presence of large quantities of aluminum hydroxide in the liquor. Ozonation was a more favorable process than membrane separation as it achieved about 92% separation of color and produced lower amounts of organic material. The treated spent Bayer liquor can be recycled to the upstream process without causing any difficulties and the purity of aluminum hydroxide product would also be improved. A comparison of preliminary cost data indicated that ozonation compares very favorably with membrane separation in this application. Key words: ozonation, Bayer liquor, aluminum hydroxide, humic species, copper ions, membrane separation, purity and economic.

Jan 1, 1994

By David Rees

Tomago Aluminium, a 400,OO tonnes per annum primary aluminium smelter in Australia, has installed Ozone for biological control of its process water. The system was designed in Australia by Ionics Watertec Engineering, whilst ANCO Australia monitors the water quality and provides technical support for the project. The motivation was initially to reduce operating costs, however investigations indicated that there were substantial environmental benefits to be achieved by the elimination of a part, or all of, the chemicals being used to control the system. Also the existing chemicals appeared to be losing their ability to control biological growth in the system, in particular, the legionella bacteria. Ozone water treatment commenced in January 1998 and after a short transition period has operated without chemical addition since. There appears to be no doubt that the biological control is effective, the clarity and purity of the water has improved and initial testing indicates that the corrosion control rate is acceptable, although some chemical corrosion control may be introduced after further testing around the total circuit to guarantee protection

Jan 1, 1999

By Tracy Morris, Shijie Wang

Preparative Continuous Annular Chromatography, or P-CAC, is an innovative separation technology, a unique approach to high-performance chromatography for the separation of PGM component mixtures from solutions. P-CAC consists of inlet/distribution head and outer/inner cylinders, and bottom plate/fraction-collection as well. P-CAC has been applied in biotechnological and pharmaceutical downstream processing. This was the first time to explore an efficient PGM separation and recovery at the Copper Refinery. Laboratory trials with using a chloride solution for raffination for PGM are described and the tests results are presented in this paper.

Mar 1, 2017

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By Kiyoshi Takai

The Para-Eco Incinerator Ash Processing System for cleaning slag has been developed after a seven-year pilot plant study. The major part of the system is an electric furnace heated to 1773 K. The feed material consists of a municipal solid waste incinerator ash mixture containing a reducing agent of a coke and an inorganic flux of calcium and magnesium. With this furnace system, three kinds of products are produced. They are an inorganic molten salt that is slag, molten iron alloy absorbing non-ferrous metals, and fly ash. Due to the reducing atmosphere in the furnace, the slag does not contain any metal components as well as chlorine components just like natural rock and/or aggregate. A retreatment plant modifies this slag into a practically useful aggregate. The plant consists of a slow cooling step for crystallizing the slag as well as a water granulation step. The iron components in the ash are reduced to molten iron droplets, which concentrate at the furnace bottom. The non-ferrous metal components such as copper, chromium, and others are absorbed into the molten iron but not into the molten slag. Volatile metals such as lead, zinc, cadmium and others as well as sodium, potassium, and chlorine go back into the fly ash. A solvent extraction method and/or other appropriate procedures can be used to extract the metal components from this fly ash.

Jan 1, 2003

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction&apos; of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012