Search Documents

By L. Katgerman, H. J. Brinkman, J. Duszczyk

"The phase formation sequence in the in-situ synthesis ofTiB2 in A1 from elemental A1, Ti and B powders is identified with a combination of DSC and XRD. After the melting of A1, A1B2 and A13 Ti are formed at the contact areas between A1-B and A1-Ti. The influence of variations in starting composition on the reaction kinetics is explained in terms of there effect on the different processes in the formation sequence. Parameters in the starting composition that were investigated are; fraction ofTiB2 forming reactants, non stoichiometric Ti:2B ratio's, and addition of alloying element Cu.It was found that a liquid Al phase is necessary for the in-situ TiB2 forming reaction from the intermediate A1B2 and A13 Ti phases. If all Al is consumed by the formation of A1B2 and A13 Ti the TiB2 formation is halted until the decomposition of A1B2 and A13 Ti .Overstoichiometric amounts of B are needed for complete conversion of the Ti, present in A13Ti, into TiB2 This is explained by the fact that some of the stable A1B12 phase is formed after the decomposition of A1B2•The addition of Cu leads to an increasing reaction rate in the A1-Ti reaction. A possible explanation for this is that the A1-Cu liquid penetrates more easily between the Ti and its surface oxide than the unalloyed A1 liquid."

Jan 1, 1998

By Kimio Itagaki, Makoto Ohtsuka, Kouki Chiba, Minoru Matsumoto

"The properties of Ni-Mn-Ga films such as chemical composition, crystal structure, microstructure and transformation temperature were investigated with respect to sputtering conditions in the present study. The Ni-Mn-Ga films were deposited on a polyvinyl alcohol substrate with a radio-frequency magnetron sputtering apparatus using the NisoMn2sGa2s and Nis2Mn:«1Ga24 targets. After separating from the substrates, the films were annealed at the temperature between 873 and 1273 K for 3.6 ks. The chemical composition of the films depended on the radiofrequency generating power, however, there was no dependence on the heat treatment temperature. Each deposited film had a columnar grain structure. After heat treatment, the width of columnar grains widened and then became indistinct with increasing heat treatment temperature. The Heusler type cubic crystal structure of the fi4n with heat treatment at 1073 K changed to the tetragonal one through the martensitic structural transformation during cooling. The martensitic structural transformation temperature increased with increasing nickel content of films, while the Curie temperature decreased. The film obtained at 200 W using the Nis2Mn24Ga24 target after heat treatment at 1073 K showed one-way shape memory effect through the reverse martensitic structural transformation during heating.IntroductionThe ternary intermetallic compound NiiMnGa has a Heusler-type crystal structure and is an intelligent material, which has a shape memory effect and a ferromagnetic property. The martensitic structural transformation occurs within the ferromagnetic temperature region. The cubic crystal structure of L21 at high temperature changes to a tetragonal one through the martehsitic structural transformation during cooling. The films of this compound can be applied for an actuator of micro-machines."

Jan 1, 2000

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012

By T. V. Jayaraman, D. Das, B. Mallesham, A. R. James

The PNN-PZT xPb(Ni0.3Nb0.67)03-(1-x)Pb(Zr0.31 Ti0 69)03 (0.2=x=0.6) based relaxor-ferroelectric material was synthesized by colurnbite precursor (NiNb206) method via conventional solid state reaction. Homogeneous mixture of required oxides and precursor was calcined at 850°C for 4 hrs to obtain phase pure perovskite. Pellets of PNN-PZT ceramics were sintered at 1100oC for 4 hrs. Phase pure perovskite structure was confirmed by the X-ray diffraction analysis. From the X-ray diffraction analysis it is also confirmed that there is a structural transformation from the rhombohedral to tetragonal with increase in PZT content and existence of morphotrophic phase boundary (MPB) at x = 0.5 composition. The morphology and microstructure of the sintered pellets were observed using the scanning electron microscope. P-E loop measurement shows the high remnant polarization (19.12 µC/cm2) and low coercive field (6.89 kV/cm) at MPB compared to all other compositions. The electromechanical planar coupling coefficient (kp) was measured through the resonance and anti-resonance method using the LCR meter. The piezoelectric strain coefficient (d33) measured directly using the d33-meter. At x = 0.5 composition the highest value of d33 = 398 pC/N is obtained.

Jan 1, 2012

By T. H. Courtney, B. R. Murphy

"Nominal room temperature mechanical alloying (MA) has been used to synthesize the high melting temperature NbC and Cu-NbC composites. Elemental powders of Cu and Nb were alloyed in the presence of either graphite or hexane to form nanocrystalline NbC or a Cu-NbC composite. Through control of hot-isostatic-pressing (H/Ping) parameters, we have been able to minimize microstructural coarsening during densijication, and have processed fully dense bulk compacts of both single phase NbC and two-phase Cu-NbC while maintaining a nanocrystalline or near-nanocrystalline structure. These materials generally exhibit high strength and low fracture toughness. However, mechanical properties vary significantly depending upon the Cu content and the method of NbC synthesis (graphite or hexane).INTRODUCTIONMechanical alloying (MA) has been recently used to synthesize a variety of inorganic solids; sulfides (1-2), nitrides (3), borides (4), and carbides (3, 5-8). One advantage of this processing route is that synthesis of fairly high melting temperature materials takes place at what is nominally room temperature. Another advantage is that the structures generated are often nanocrystalline in scale, with attendant interesting properties. The consolidation of these fine structures into near fully dense or fully dense materials while limiting microstructural coarsening is a challenge that has just recently seen limited success (5, 9). We report here on some recent studies of ours dealing with crystallite size and structural analysis of NbC and CuNbC composites consolidated to full density from mechanically alloyed powders. Bulk mechanical properties and their dependence on milling parameters are also presented."

Jan 1, 1994

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By R. D. Brittain

In order to analyze and control the transport of harmful trace-element impurities in various smelting processes, it is necessary to have fundamental information about the chemical thermodynamic properties of the pertinent condensed and vapor phases. This paper describes recent thermodynamic studies of the gaseous arsenic sulfides and of the activity of arsenic in a copper-iron sulfide matte phase. These studies were carried out by high temperature mass spectrometry and by effusion vaporization techniques, which permitted clear identification of the molecular species involved, a decided advantage in such complex systems. The nature of the results obtained and comparisons with previous interpretations will be described.

Jan 1, 1983

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By Michal Rzyman, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Thermodynamic considerations indicate that heavy metal oxides should easily react with HBr, the main gaseous product from the thermal decomposition of tetrabromobisphenol A (TBBPA), forming low boiling point metallic bromides suitable for volatile separation. Mechanisms and kinetics of the bromination reactions must be well recognized prior to developing of a new treatment for the simultaneous recycling of plastic waste containing brominated flame retardants (BFRs) and metal oxides (printed circuit boards, automotive shredder residue, plating sludge, metallurgical dusts). In this work, a differential scanning calorimeter and laboratory-scale furnace were used to investigate the possibility and conditions of the bromination of ZnO by product of thermal decomposition of TBBPA. The formed solid, condensed and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography and gas chromatography coupled with mass spectrometry. Introduction Tetrabromobisphenol A (TBBPA) is the largest volume brominated flame retardant (BFR) in production today and is used in more than 70% of the world’s electronic and electric (E&E) appliances [1]. The growth in the production of E&E products and the fact they become obsolete so quickly cause significant problems in the safe disposal and recycling of the electrical and electric waste (E-waste) and other BFR-containing waste [2]. Among various treatment processes, thermal methods are most useful since they allow the recycling and recovery of both the organic and inorganic fractions of the waste. However, incineration of the BFR-containing wastes results in the emission of hazardous organobromine compounds, while the main portion of bromine released from decomposed BFRs is present in flue gas as hydrogen bromide (HBr) [3]. HBr, which is known to damage incineration systems, seems to be a very effective bromination agent for many metallic oxides present in waste. The concept of this study is to take advantage this of its property."

Jan 1, 2008

By Rzyman Michal, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Tetrabromobisphenol A (TBBPA) and many systems based on the synergistic effect of brominated organic compounds with Sb2O3 are extensively used as effective brominated flame retardants (BFRs) in many materials such as plastics and textiles. Thermal degradation of BFR containing plastics leads to the formation of hydrocarbons and gaseous compounds such as HBr and SbBr3. Our thermodynamic considerations indicate that these gases can act as bromination agents for metallic oxides such as ZnO, Cu2O, CuO, PbO and FeO. Moreover, these metallic oxides have the thermodynamic tendency to brominate easier than does Sb2O3. The aim of this study was to investigate experimentally the reactivity of ZnO with 1) HBr originating from the thermal decomposition of TBBPA and 2) SbBr3, which is formed during thermal degradation of brominated flame retardant plastics. The thermal treatments of the mixture of compounds of interest were investigated by thermogravimetry coupled with mass spectrometry.IntroductionTetrabromobisphenol A (TBBPA) and many systems based on the synergistic effect of brominated organic compounds with Sb2O3 are extensively used as effective brominated flame retardants (BFRs) in materials such as plastics and textiles. For instance, 4.5 million tons of flame retardant plastics containing BFRs are produced in Japan each year. Thus, in thermal treatments such as the incineration and melting of solid wastes, BFR containing plastics are intentionally or unintentionally included in the wastes. Thermal degradation of BFR-containing plastics leads to the formation of hydrocarbons and gaseous compounds such as HBr and SbBr3 [1-5]. Our thermodynamic considerations [6] indicate that heavy metal oxides such as ZnO, Cu2O, CuO, PbO and FeO should easily react with HBr prior to Sb2O3 and also with SbBr3, the main gaseous product in the thermal decomposition of TBBPA, forming low boiling point metallic bromides suitable for the volatile separation of heavy metals. The metal oxides are also expected to qualitatively and quantitatively affect debromination and decomposition of the flame retardant."

Jan 1, 2008

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By E. M. Alcântara

This paper describes some aspects about the relationship between copper electrorefining addition reagents and the hydrogen in the cathode. The conditions of electrorefining were studied by factorial design methods. The advantages of this technique are reduction in the number of tests, well organized experiments; improvement in productivity and reliability of results. The dosage of the two main addition agents, glue and thiourea, were varied simultaneously and compared with the hydrogen content in the cathode. The influence of these factors, as well their interactions were analyzed by statistical methods denominated ANOVA (Analysis of Variance). The increase of thiourea quantities, within of levels studied, influenced significantly at 95% confidence in the hydrogen content in copper cathode.

Jan 1, 1999

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai

The purity of the electrolyte has an important influence on the content of the impurities in electrodeposited silicon. In this paper, effects of electrolysis temperature, current density and the time on the concentrations of two important impurities: phosphorus and iron in the electrolyte were investigated during the purification of Na3AlF6-10%K2SiF6-AlF3 melt. It was observed that the concentrations of P and Fe in the electrolyte decreased with the electrolysis temperature, current density and the electrolysis time increasing. X-ray fluorescence (XRF) of the electrolyte shows that the concentrations of P and Fe decrease from 4.2ppmw to 1.3ppmw and 204.0ppmw to 42.6ppmw, respectively. The removal rates of P and Fe are 69.08% and 79.12% when the electrolysis was performed for the duration of 3 hours and at a current density of 20mA·cm-2 while the operating temperature was 1225K.

Jan 1, 2015