Search Documents

By J. W. Matousek

Copper losses in smelter slags are :typically normalized with some form of the distribution coefficient, written as the ratio of the weight percent assays of metal in slag to the metal in matte or its inverse: L(s/m) = %(Cu)/%[Cu] or L(m/s) = %[Cu]/%(Cu) However, this simple approach ignores the dynamics of the smelting process. It overlooks the effect of the chemical work done in producing a given matte grade from concentrates of different grades -- or from a single concentrate blended with varying quantities of copper bearing precipitates or reverts. This paper examines the combined influences of matte grade and the work done in smelting on the copper content of smelting furnace slags. A simple model for the relationship is proposed.

Jan 1, 1999

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By Yoshiyuki Matsui

As one of the factors of frequent troubles on iron-making blast in recent years, increased size of the blast furnace and high-productivity operation are pointed out. Consequently, great importance is attached to deadman shape and solid flow at the lower part of furnace. In the present study, firstly, the blast furnace raceway formation under the intensive coal injection by measurement of micro wave reflection gunned through a tuyere is discussed. As the flow rate of coke as the momentum of coke into raceway decreases by combustion of coal injected into tuyeres, the depth of raceway defined as the maximum position of micro wave reflection is easy to contract. It is expected that this new technology could detect the raceway collapse phenomena in short time and that the stability of raceway in coal injection is different from that in all coke operation. Secondly, the reduced stockline surface profile was measured by the reflection intensity of microwave struck from the furnace top after blow-off with stockline reduced, and investigation was made on the countermeasures for changes in the raceway depth and furnace body profile during operation. As a result, it has been clarified that flow-down of coke into the lower part of blast furnace and inflow into the raceway are greatly subject to the existence of deadman which is the packed structure of the lower part of furnace, and further, they are closely related to dynamic behavior of the raceway, and affect changes of the furnace body profile.

Jan 1, 2006

By Sun Ying, Zhang Jing, Li Qiuju

A new process of enrichment Cu in molten copper slag under electric field is presented in this article. The experiments were carried out in the laboratory on a kilogram scale. The mobility of copper slag was improved by the technique of carbon reduction. The effects of temperature, electric field strength and intermittent feeding speed were investigated on Cu migration. The results showed that the best experimental conditions were the temperature at 1523K, electric field strength was 1.5V•cm-1 and feeding rates was 15 g•(10min)-1. The copper content of the slag decreased below 0.6wt%. The process was compared to the traditional electric furnace process of slag cleaning, there was reduced the energy consumption and heat loss, and also harmful gas emissions such as SO2 and CO2, accompanied by improved the efficiency of slag cleaning.

Jan 1, 2016

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By Lidong Teng, Seshadri Seetharaman, Aida Abbasalizadeh

0In the present paper, the feasibility of the recovery of dysprosium from spent Nd-Fe- B magnets containing approximately 9 wt% Dy was investigated by using molten salt process. The salt bath consisted of a mixture of NaCl-KCl-LiCl corresponding to the ternary eutectic composition. AlCl3 was used as a chlorinating agent in order to enable an efficient dissolution of metal in the molten salt phase in the salt bath. The metal chloride which is formed as the result of chemical reaction between the metal in magnet and AlCl3, is subsequently subjected to electrolysis in order to be deposited on the cathode. Graphite rods were dipped in the salt bath as electrodes and alumina crucibles were used as the containers for the electrolytic cells.

Jan 1, 2014

By Heinz Böni, Christian Ludwig, Bernhard Steubing, Uca Silva

"Chile will soon have to find solutions for dealing with rapidly growing quantities of Waste Electrical and Electronic Equipment (WEEE) due to its strong economy and fast increase of internet and communications technology usage. To support this process, the state of the Chilean recycling infrastructure as well as government, industry and consumer efforts to deal with ewaste were analyzed. Current e-waste quantities were assessed and future flows were predicted using a material flow analysis model. In this model computer hardware was used as tracer equipment for WEEE. Best available numbers indicate that today’s formal recycling infrastructure receives less than 3% of the annual quantities of computer waste. This study represents the most comprehensive analysis regarding e-waste in Chile, identifying relevant streams of e-waste and providing a basis for authorities and producers of electronic goods in order to take the necessary actions to establish an adequate recycling system.IntroductionSince 1991, Chile has experienced a period of strong economic growth. It is amongst the countries with the fastest development in the sector of Information and Communication Technologies (ICT) in Latin America and the number of people with access to ICT has been growing rapidly. The high growth rates of the computer market over the last years are representative for the ICT sector with the consequence that the generated quantities of electronic waste are increasing rapidly [1, 2].Waste Electrical and Electronic Equipment (WEEE) or e-waste is “any appliance using an electric power supply that has reached its end-of-life” as defined by the OECD [3]. Even though the overall waste management in Chile has improved much over the last decade, the issue of ewaste was hardly addressed. Due to the value of the materials contained in computer waste - such as precious metals, basic metals as copper or plastics - it may be assumed that an important quantity is already being recovered. This usually takes place on the informal market under questionable conditions for human health and the environment [1, 2, 4]."

Jan 1, 2008

By Heinz Boeni, Daniel Ott, Uca Silva

"Latin America is facing a rapid increase in internet use. Penetration with electronic equipment is in some countries approaching the level of industrialized countries. There is an evident need to resolve the management of “end-of-life” computers and other electronic equipment. Several studies in Latin America assessed the increasing e-waste quantities and confirmed the importance of a sustainable e-waste management. This paper gives an overview on the status on e-waste management in Latin America, explains the challenges for establishing an e-waste management system in a developing country setting and highlights the social and economic potential and the possibilities of a regional approach.IntroductionGlobal ICT-Trade and generation of e-waste from ICTThe global production of electronic devices and particularly of Information and Communication Technologies (ICT) faces the biggest industrial expansion of the history: OECD figures show that global trade of ICT technologies has reached 7.7% of the gross world product by 2004, the major proportion accruing from China [1]. In 2006 an estimated 230 million computers and 1 billion cell phones have been sold worldwide which corresponds to a volume of 5’848’000 t [2]. As a consequence, Waste from Electrical and Electronic Equipment (WEEE), or e-waste, is by far the fastest growing waste component. It reaches more than 5% referred to Municipal Solid Waste and e-waste generation in developing countries according to UNEP is expected to triple by 2010 [2].According to the OECD e-waste is “any appliance using an electric power supply that has reached its end-of-life” [3]. The European WEEE directive [4] distinguishes 10 categories of ewaste: Big household appliances, Small Household Appliances, IT and Telecommunications Equipment, Consumer Equipment, Lighting Equipment, Electrical and Electronic Tools, Toys, Leisure and Sports Equipment, Medical devices, Monitoring and Control Instruments, and Automatic dispensers. In this paper e-waste and WEEE are used as synonyms. Focus will be laid on e-waste from IT equipment (IT-waste), corresponding to category 3 of the European WEEEDirective."

Jan 1, 2008

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By C. O. Bounds

Management of emission control dust from electric? arc furnace (EAF) steelmaking as an RCRA-EPA listed hazardous waste places economic and environmental pressures on the steelmaking industry. Horsehead Resource Development Company, Inc. (HRD) serves the industry by recovering nonferrous metals from the dust in rotary kiln plants in Palmerton, PA and Chicago, IL, and has demonstrated the commercial viability of its patented coal-fired FLAME REACTOR Process. However, because of location and/or regulation, many steelmakers could be more economically served via on-site processing of its dust. Therefore, in 198-7, through a contract with the Gas Research Institute, HRD embarked on a program to develop a gas-fired reactor and test a prototype unit. The development program has successfully proven the environmental, technical and economic performance of the concept. Consistently high zinc, lead and cadmium recovery to an oxide concentrate as well as production of a nonhazardous, delistable slag have routinely been achieved. The gas-fired FLAME REACTOR field experiment results and the economic performance of on-site or smaller regional plants will be highlighted.

Jan 1, 1990

By Åke Saudström

An EAF dust sample generated in a scrap based steel mill was treated by a combination of hydro- and pyrometallurgial techniques. The EAF dust contained mainly ferritic spinels forming solid solution phases according to the general chemical formula (MnxZnyFe1-x-y)Fe2O4 and other oxide phases such as ZuO. CaO and Ca2Fe2O5. The EAF dust was first treated by hydrochloric acid leaching at p8=3 which dissolved 63% of the zinc. The pyrometallurgical treatment of the leaching residue was studied using an induction heating system to simulate some important operations of EAF smelting of the residue in combination with steelmaking. The leaching residue was mixed with carbon powder to obtain a mixture with 52.1% ZnFe2O4 and 175% carbon. The mixture, scrap, and slag former were charged together in a crucible and heated to attain a melt temperature around 1650°C. The effects of different amounts of mixture on the zinc balance and iron recovery were examined. Based on the test results, suggestions are made for the EAF recycling procedure of the leaching residue.

Jan 1, 2003

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By J. R. Goode

There are at least a dozen methods of selectively removing cerium from a mixture of the rare earth elements (REE) including separation techniques based on the oxidation of cerium to the quadrivalent state. Several of the oxidation processes have been operated on a commercial scale, others have been tested and in some cases are part of proposed flowsheets. In this paper, we describe and compare the various methods. We also present preliminary estimates of the costs of early Ce removal and discuss recovery and purity aspects of the options.