Search Documents

By W. D. Cho

Fast dissolution of nonmetallic inclusions such as alumina particles in molten slags has been required in secondary steelmaking -ladle and tundish - to minimize the amount and the size of nonmetallic inclusions in steel products. In the present work, the dissolution behavior of alumina particles in molten CaO-A12O3 and CaO-A12O3-SiO2 slags at the temperatures between 1450 and 1550°C have been investigated in terms of kinetics and mechanism. Alumina particles were added directly into the slags and the variation of the particle size with time was determined using optical and electron microscopies. The conventional types of slag for ladle and tundish were included in the dissolution study. The effects of Al2O3, Siq, CaF2 and MgO contents on the dissolution rate of alumina particles have also been determined. The diffusion boundary layer between alumina particle and bulk slag phase has been observed and analyzed using SEM and EDS. Based on the analysis of kinetic data and the boundary layer, the dissolution mechanism has been discussed.

Jan 1, 2002

By Shigeru Ueda, Shin-ya Kitamura, Shohei Koizumi, Xu Gao

Steelmaking slag was confirmed to be a useful fertilizer for paddy growth as it efficiently supplies Ca and Si to soil water. In addition, supplement of Fe from slag fertilizer has been expected to suppress the H2S generation in paddy soil, especially for the degraded paddy soil. However, on the basis of our previous research, the Fe dissolution ability changed with slag brands, and even some brands could dissolve Fe under paddy soil pH, the supplying ability were not high. To improve Fe dissolution, we found that among various kinds of Fe-rich mineralogical phases in slag, the CaO–SiO2–FeO glassy phase showed highest water solubility of Fe. Because the CaO–SiO2–FeO glassy phase was a quenched molten phase, its dissolution behavior may depend on chemical composition, and this is important for controlling slag composition to produce fertilizer which can easily release Fe. Therefore, in this research, the CaO–SiO2–FeO glassy phase of various CaO/SiO2 ratio, Fe2+/T–Fe ratios, and FeO contents were synthesized, and the dissolution behaviors of Fe as well as other cations from these synthetic glassy phases into an aqueous solution at pH of 5 were investigated. The result showed that the dissolution ratio of Fe increased significantly by increasing Fe2+/T–Fe ratio. An increase in FeO content of glassy phase also increased the dissolution of Fe. In addition, the Fe dissolution ratio showed a local maximum with increasing CaO/SiO2 ratio.

Mar 1, 2017

By Shuqiang Guo, Dingsheng Tan, Weizhong Ding, Zunyu Hu

"The mixture of hydrochloric acid and magnesium chloride is a good lixiviant for leaching of laterite. The solution can enhance the leaching ability because of the proton activity deviated positively from ideal. Otherwise, the existence of magnesium chloride in the lixiviant affects the dissolution behavior of magnesia, which may be an advantage of the process with less hydrochloric acid consumption. An investigation of magnesia particle dissolved in strong hydrochloric acid solution has been conducted. Influences of concentration of the magnesium chloride and hydrochloric acid and temperature on magnesia dissolution were studied. The dissolution mechanism was also discussed in this paper.IntroductionThere has recently been much interest in the use of hydrochloric acid leaching processes for recovering metal from ores or secondary resources [l-41_ Compared with sulfuric acid, the use of hydrochloric acid as lixiviant offers significant advantages including faster leaching kinetics even at atmospheric conditions, higher leaching rate and greater solubility for most metal chlorides [5-61 .With the gradual decline of the nickel sulfide supply, the extraction of nickel from laterites has become increasingly attractive [7-s1. Nickel may be co=ercially recovered from laterites both by pyrometallurgical and hydrometallurgical processes. The drawbacks of pyrometallurgical processes include the requirement of high grade ores, substantial energy input and loss of cobalt bound within ores. The extraction of Ni from lower grade nickel laterites ores is suited by hydrometallurgical routes, which play an increasingly important role with depletion of higher grade deposits."

Jan 1, 2014

By Wiraseranee. Chompunoot, Kazuki Morita, Toru H. Okabe

"Aiming at the development of more effective recycling processes, dissolution behavior of rhodium into molten slag was investigated. Using a pure rhodium crucible and Na2O-SiO2 slag system, equilibration experiments were carried out for 18 h at 1423-1623 K under various oxygen partial pressures of 0.005-1 atm with varied slag basicity. Rhodium solubility increased with increasing oxygen potential, slag basicity, and temperature. Rhodium dissolved into slag as rhodate ion ([RhO2]-) by the endothermic reaction: Rh(s) + 3/4O2(g) + 1/2O2-(in slag) = [RhO2]-(in slag). In the dissolution reaction, the “rhodate capacity” of slag is newly-defined. The correlation between rhodate capacity and optical basicity is reported.IntroductionDue to its high chemical resistance and outstanding catalytic properties, rhodium (Rh), one of the platinum group metals (PGMs), is utilized in various applications such as catalysts, molten glass vessels and containers, and electronic devices. Owing to the rarity of Rh resources in nature, recycled Rh from scraps such as spent automobile catalytic converters is currently considered as an important source of Rh supply [1]. According to the recycling practices, Rh is currently mainly recovered from scraps along with other PGMs such as platinum (Pt) and palladium (Pd) by a dry process (e.g., smelting), a wet process (e.g., leaching and subsequent separation of PGMs from aqueous solution), or a combination of both processes [2]-[4]. Among these processes, smelting is commonly applied because PGMs can be effectively separated from a relatively large amount of various impurities coexisting in scraps. In the smelting process, Rh and other PGMs are collected in the collector metal (e.g., iron and copper), and impurities in scraps are removed into slag [4]-[6]. The process may be carried out at a temperature range of 1573-1973 K, in either an oxidizing or reducing atmosphere. Due to the high oxidation resistance at high temperatures, Rh is expected to be collected efficiently in the metal collector rather than being oxidized and forming RhOx in a molten slag. However, Rh loss into slag does occur in this process [7]."

Jan 1, 2011

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By Xiaohui Li, Lianyun Liu, Hongmin Zhu, Chunfang Zi, Kai Huang, Hongjie Li

"The dissolution kinetics of steelmaking slag in pure water was studied, and the relative influential factors were investigated. The dissolution behavior of slag particles in water was well described by Noyes–Whitney equation, and for this kind of sparingly soluble rigid mineral this simple model was extensively applicable to describe their dissolution process. Experimental data were also obtained to confirm the significant promotion effect on the growth of some algae.1 . IntroductionIt has been found that the population of phytoplankton distributed in the ocean was significantly related to the concentration of some elements [1]. For example, silicon and iron were very low in the high-nitrate low-chlorophyll (HNLC) areas, which was the main factor limiting phytoplankton and other biomass growth in these open ocean surface water [7]. The silicon and iron-rich test also confirmed that the supply of these elements had the direct effect on the growth of phytoplankton processes at HNLC areas [2-8]. So in order to promote the growth of phytoplankton in these ocean areas, providing some of these elements into these ocean areas is a natural idea for choice. Steelmaking slag is a good resource for consideration because it usually contains silicon, iron, phosphorus and other elements that are necessary for the growth of phytoplankton [8-10].Haraguchi has proposed the following idea that [5-6], if steelmaking slag can be spread to the open ocean, the trace components like silicate, iron and phosphate as the indispensable nutrients for the growth of phytoplankton, will be leached into the sea water, not only promoting the growth of phytoplankton, but also making good use of these huge amount of steelmaking slag produced every year. Based on this idea, they have carried out studies in recent years and they found that silicon and iron in the slag could be extracted into seawater effectively and play a positive role in the growth process of many algae. About the dissolution of the steelmaking slag, the Japanese scholars' research work mainly focused on the thermodynamic analysis of its dissolution possibility, and in the process of dissolution they tried to adjust the pH value of the seawater by continuously adding hydrochloric acid, which was deviated from the natural conditions of dissolution, and so the laws drawn under these special conditions can not give the identical guide to the practical application. Therefore, it is quite necessary to investigate the dissolution behavior of the steelmaking slag in the seawater at the normal pH range without adjustment to simulate the dissolution possibility under the natural conditions. In the present study, the silicon extraction behavior from the steelmaking slag was investigated and the dissolution kinetics in this process was also discussed in detail. Further studies were also performed here to evaluate the promotion of steelmaking slag on the growth of algae."

Jan 1, 2011

By Kazuki Morita

Dissolution mechanism and solubility of chlorine in the oxide melts, such as CaO-SiO2-Al2O3 (-Na2O), Na2O-SiO2-Al2O3 and CaO-SiO2-FeO systems, have been equilibrium technique was employed with controlled Po2 and PCl2, (Po2 = 10-6 -10 19 atm, PCl2 10-6 -10-13 atm at 1673-1748 K). The solubility of chlorine in the 40mass%CaO-40mass%SiO2- 20mass%Al2O3, slag was found to vary in proportion to Pb2/ w and pc/z/p' which proved that chlorine dissolved in the melts as C1 anion. Hence, the chloride capacity (CCI-), indicating the ability of molten oxide to absorb chlorine, has been defined as; The Ccl value was observed to increase with increasing slag basicity and temperature, and showed a reasonable relationship with that Of CS2-. Based on the result obtained in the present study, chlorine distribution during incineration with slags was predicted quantitatively.

Jan 1, 2003

By Shuo Wang, Yu Wang, Bing Xie, Rui Tang, Hong-Yi Li, Kun Wen

"During present converter vanadium extraction process, phosphorus could not be removed from hot metal due to absence of CaO in slag though it is an efficient way for vanadium extraction. In order to improve the phosphorus remove and produce CaO-containing vanadium slag, which could be directly used in subsequent roasting process, during the converter vanadium extraction process, lime dissolution in FeOx-Si02-V203-Ti02 slag was investigated by using a rotating cylinder technique and the slag-lime interface was characterized by SEM/EDS. Results showed that changes in the slag chemistry and phase compositions during the lime dissolution process were similar to that in CaO-Si02-FeOx based slag during the BOF process. The V and Ti in the slag were expected to diffuse into the lattice of2CaO·Si02 solid solution, which formed a rather thinner layer in thickness at the slag-lime interface than that in BOF process, leading to improvement of lime dissolution in the slag.IntroductionVanadium is important material that widely applied in industries. The traditional technique to extract vanadium was to leach vanadium after sodium salt roasting. However, the sodium salt roasting process has several problems including lower yielding rate[!] and environmental pollution[2]. Therefore, the more environment-friendly technique of calcium roasting[3-4] was proposed. In order to increase roasting efficiency of vanadium slag, it is essential to study the dissolution/reaction mechanism between lime and vanadium slag. Many investigations about the dissolution reaction of lime in molten slag have been carried out from the standpoints of rapid slagging to De-Pin steelmaking process[5-6]. However, their studies were focused on BOF slag and the reaction mechanism between solid lime and slag containing vanadium has not been reported yet. In present work, the dissolution process was studied with rotating cylinder technique and the reaction interfaces were observed and analyzed by SEM/EDS to elucidate the dissolution mechanism of lime in vanadium slag. This work was supported by National Natural Science Foundation of China No. 51090382."

Jan 1, 2013

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid alumina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scaru;ling electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By Jonkion M. Font

As a comprehensive contribution to the understanding of oxygen-blowing of matte smelting, the copper and nickel solubilities between the FeOx SiO2-MgO slag with saturated SiO2 and the Cu2S-Ni3S2 FeS matte with the NCu/(NcU+NNi) of 1, 0.75, 0.5, 0.25 and 0, in a MgO crucible were investigated at 1573 K under controlled partial pressures of SO2 at 0.1, 0.5 and 1 atm. The partial pressures of SO2, S2 and O2 were controlled by using an Ar-SO2-S2 gas mixture after passing through a sulfur reservoir. It was clarified that, at a given matte grade, the solubility of copper in the slag was independent of pso2 while that of nickel increased with increasing pso2. This notable difference was considered to be ascribable to the chemical formulas of the mono-metallic sulfides in which one copper atom combines with ½ sulfur atom while one nickel atom combines with 2/3 sulfur atom. It was also clarified that, at a given iron content in the matte, the pot and ps2 were independent of the matte species. This was ascribable to aFeS in the matte, which was independent of the matte composition, Ncu/(Ncu+NNi), at a given iron content in the matte.

Jan 1, 1999

By Jogre A. S Tenório

he aim of the present investigation was to investigate technological features of the Fe-NbC dissolution in liquid Fe-C alloys. Fe-NbC is a Ferro-niobium alloy with 7%C, has a particle size smaller than 150 pm and its micro constituents are polygonal niobium carbides and an iron matrix. The obtained dissolution time was less than one-minute and the yields were in the range of 80-90% at 1873 K. In the Fe-NbC dissolution process, the dissolution occurs at first, and as a consequence the niobium carbides become free to dissolve. These carbides will dissolve until the melt reaches a saturation point. The non-dissolved carbides remain trapped in the liquid or will form a dross. The addition yields decreases when the niobium concentration reaches this limit value, that depends on the carbon concentration. These define a saturation curve.

Jan 1, 1994

By Batric Pesic

Recovery of gold from refractory ores was studied by pressure oxidation as the method of ore pretreatment followed by bromination of oxidized residues. Three different ores were examined, Au-Ag, Au-Ag-Te, and Au-silver free ore. Pyrite was the major host mineral for gold in these ores. The effect of pressure oxidation parameters (temperature, pressure of oxygen, time, and pulp density) on subsequent bromination under standard conditions was examined. Bromination of residues produced under standard pressure oxidation conditions was examined as a function of: temperature, bromine and sodium bromide concentration, and time. Recovery of gold on activated carbon, from the pulp after bromination, was studied too. Recovery of gold from silver containing ores was lower (87-91%) than the recovery of gold from silver free gold ore (97%). In each studied case, the presence of activated carbon in the pulp further increased the recovery of gold.

Jan 1, 1992

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Kenneth N. Ham

Hydrometallurgy covers a wide spectrum of areas and its knowledge base is enlarged and enhanced by contributions from many other fields. Dissolution of metals and alloys in aqueous media will be used to illustrate how rich the field of metal extraction can be. Comprehensive understanding of the fundamentals of metal and alloy dissolution in aqueous systems requires creative application of thermodynamic principles, solutions chemistry, ligand complexation theory, electrochemistry, transport phenomena and heterogeneous kinetics. In addition, recent developments in instrumentation in the fields of interfacial phenomena and corrosion have tremendously advanced the field of metal extraction in aqueous system. The close relationship between metal extraction in aqueous systems and various physicochemical phenomena occurring in corrosion and interfacial systems will be discussed and illustrated with examples.

Jan 1, 2002

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By R. C. Hubli

A panial equilibrium model? to simulate the dissolution of millerite (NiS) in aqueous solutions containing copper(II) chloride as the oxidizing species has been developed. The predominant copper(I) and copper(II) species are CuQ3 and CUO2 respectively. The model computes the initial concentrations of the species present in the aqueous phase under the specified input conditions, prior to the simulation of dissolution. During the dissolution of millerite, nickel enters the leach liquor as NiH and it has been found that the H+ decreases as a function of NiS dissolution. The simulation has been accomplished under conditions prevailing during actual dissolution, with only one mineral undergoing dissolution. The model can be applied for the simulation of co-dissolution of two or more sulfides. Under the given conditions, the precipitation of Cu1(OH»)O is negligible but loss of Cu(1l) could be significant if the initial H+ is lower than 0.03 M. The results of the simulation compare favorably with experimental observations.

Jan 1, 1996

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012