Search Documents

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By Kyong-Hwan Lee

This paper is focused on describing the pilot and demonstration plants for pyrolysis process of mixed plastic wastes developed at Korea Institute of Energy Research (KIER). These plants were constructed at KIER (300 ton/yr) and also Korea R & D Company (3,000 ton/yr) in Kimjae city, in Korea. The raw material used was mixed plastic wastes that were generated from household and industry, etc. The liquid products obtained by pyrolysis at around 400°C were used as an alternative fuel oil. These processes were controlled by automatic control system with continuous operation in a control room. Main process units consist of automatic feeding, melting, thermal cracking systems and vacuum distillation. Their characteristics were automatic pyrolysis operation under vacuum atmospheric pressure, continuous control in feeding of raw material and discharging of solid residue, the recirculation of cracked reactant with a high temperature into the melting reactor and continuous pyrolysis of reactant in circulation thermal cracking system such as constant stirred tank reactor (CSTR), plug flow reactor and light/heavy oil separator, in order to maximize the efficiency of light oil products like kerosene and diesel. In addition, the process performance of pilot plant was described.

Jan 1, 2006

By H. Ipek

In this study the effects of interstitial ratios on k-feldspar samples were investigated. The k-feldspar samples were taken from Egypt using dry batch grinding conditions and a kinetic model. Three different mono size fractions (-3350+2360, -850+600 and -300+212 µm) were ground separately for 0.5, 1, 4, and 8 minutes and at four different interstitial ratios (125%, 100%, 75% and 50%) using a Bond mill with a mixture of five ball sizes. The mill used was at a size of 30.5 cm diameters, with 30.5 cm length, providing a total mill volume of 22272 cm3. The mill has a total mass consisting of 22648 g. steel ball mixtures of 38.10, 31.75, 25.40, 19.05 and 12.70mm diameters, occupying 22% of mill volume. The mill rotates at a speed of 70 rpm. The weights of the feed charges were 3000, 2000, 1000, and 500 g for 125%, 100%, 75% and 50% filling of the interstices of the balls respectively. The specific rate of breakage (Si) was determined from the top size fractions at different grinding times that were mentioned above and the model parameters were compared for the four different powder filling ratios (U). In many investigations, it has been found that an interstitial filling ratio of U = 0.6-1.1 is a good powder ball loading ratio to give an efficient breakage in a ball mill. In this study, it was found that U=1.25 is a good ratio for K-Feldspar.

Jan 1, 2006

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By Stanko Nikolic

Ferrous calcium silicate slags are potentially important for future practice in copper converting operations and processes and can be described by the ?Cu2O?-FeO-Fe2O3-CaO-SiO2 system. Despite its industrial importance the phase equilibria in this system have not been fully investigated. Characterization of this slag system is necessary to improve the design and optimization parameters of new processes, including fluxing and operating temperatures. Experimental methods have been developed to investigate the phase equilibria of these slags at copper saturation and without copper. This technique involved equilibration of samples at a fixed oxygen partial pressure, rapid quenching, and analysis of the compositions of phases using electron probe x-ray microanalysis (EPMA). Liquidus and solidus data are reported for the primary phase fields of spinel, wollastonite and tridymite at 1250oC and an oxygen partial pressure of 10-6atm. The resulting data has been used to construct liquidus isotherms in the ?FeO?-CaO-SiO2 system both in equilibrium with and without molten copper. The experimental results were compared with the predictions of a thermodynamic computer package utilizing a self consistent thermodynamic database. The predictions of the model were in good agreement with the experimental isotherms when projected onto the FeO-CaO-SiO2 section, however the copper concentrations in the liquid phase at copper saturation were lower than predicted using the current database of the model.

Jan 1, 2006

By Norihiro Murayama

The hydrothermal syntheses of zeolites from coal fly ash were carried out using NaOH and KOH as an alkali source. The cation exchange capacity (CEC) and the ion exchange selectivity were investigated for the zeolites synthesized by a hydrothermal treatment. The effective usage of the zeolite as a cation exchanger was considered from the viewpoint of engineering. Zeolite P, HS (hydroxysodalite) and K-CHA (potassium-chabazite) are mainly formed as zeolite species in NaOH or KOH solution at 393K. The zeolite P and K-CHA have a large exchange capacity as a cation exchanger. The cation exchange isotherms of various monovalent and divalent cations with various zeolites are investigated. The order of selectivity of the zeolites is as follows, NH4+> K+> Li+.For the divalent cation, the largest removal amount is obtained for Pb2+ in the low equilibrium concentrations below 0.2mmol/dm3, and almost perfect removal can be achieved for Pd2+. The order of selectivity of zeolites in low concentration is expressed in the following order; Pb2+> Co2+> Cd2+> Ca2+> Mg2+> Ni2+. Ii is considered the zeolites obtained from coal fly ash can be used as an excellent cation exchanger.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By Ramiro Escudero

Michoacan?s beach sands with interesting concentrations of ilmenite were studied to produce titanium by hydrometallurgical techniques. Nevertheless, among titanium species, there are different additional components of Michoacan?s beach sands which could be of interesting applications. Some of them are likely to be applied for the manufacture of nanocrystalline ceramics. Although, the most applied mineral dressing to treat these kind of sands, that contain magnetic species (i.e., ilmenite, magnetite), is a combination of gravity separation and magnetic separation, it could be of a great deal of benefit to apply the information regarding the surface characteristics of the sands? components, in order to study the application of flotation technologies to separate selectively those species with commercial value.

Jan 1, 2006

By Steven Wright

BHP Billiton?s Olympic Dam copper flash smelter employs the direct to blister process for smelting high grade copper concentrates. SO2 evolution during tapping gives rise to safety concerns. A thermodynamic model for the blister copper (Cu-Fe-S-O) was used to predict the volumes of SO2 evolved. The Multiple Phase Equilibria Model (MPE) was used to evaluate the slag chemistry inside the furnace. The blister copper model was used to explore the relationship between %S and %O in the copper and the amount of SO2 evolved on cooling. The volume of SO2 evolved was sensitive to the O content with reduction to levels below 0.2 ? 0.15% likely to suppress SO2evolution on cooling. Concentrations of S and O in copper samples from trials generally lay above the equilibrium line calculated for an average temperature of 1275C and a partial pressure of SO2 of 1 atm. Consequently there is a thermodynamic driving force for SO2evolution when cooling to this temperature during tapping. A number of potential process options to suppress SO2 evolution on tapping were investigated thermodynamically. Some of the options require treatment of the blister in a forehearth or separate furnace, while others impact on current practises in the flash furnace with slag present. The opportunities that these options present are discussed.

Jan 1, 2006

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By Leszek Blacha

Since several years aog there is noted an increasing importance of the metallurgical vacuum technologies. This refers mainly to the extra furnace steel treatment processes, melting of steel and special alloys in the induction and arc vacuum furnaces, as well as refining processes of nonferrous metals. In the presented work, there is discussed a phenomenon of evaporation of volatile components of metal bath under reduced pressure with description of kinetics of this process. In this article are presented are the evaluation of the mass transfer coefficients in the melt and gaseous phase. Based on results of our own research on removal rate of impurities from liquid copper (bismuth, lead) in vacuum refining process, it is determined the thickness of hypothetical boundary layer in the gas phase. This allowed to formulate a general kinetic equation defining the evaporation rate of gaseous components from metal bath. The values of mass transfer coefficients determined from this equation were compared with experimental results by other authors working on the evaporation effect of melt components of metal alloys.

Jan 1, 2006

By T. I. Arbuzova

The present work presents the original data concerning using a high pressure torsion method and a shock wave loading technique to produce compact oxide nanomaterials and investigations of the effect of severe plastic deformation on a microstructure, crystal lattice and stability of these compounds. This allowed us to compare two ways of deformation action that can be characterized as quasi-static and dynamic effect, correspondingly. Particular attention was paid to a stoichiometry and surface composition changes upon severe plastic deformations. A procedure for studying chemistry of the oxide nanomaterials by means of nuclear microanalysis and Rutherford back scattering has been worked through. For surface studies the X-ray photoelectron spectroscopy has been used. It was shown that both distortion methods permit to produce massive nano-scale oxide materials from the coarse-grained powder during a single technological cycle. Bulk nanocrystalline materials based on LaMnO3, TiOy and ZrO2:Y2O3 were obtained by the quasi-static deformation technique. Nanoscaled ceramics of CuO, Mn3O4 and LaMnO3 were produced by the dynamic deformations. The density of the nanoceramics comes to 99%. Size effects and specific imperfection of the nanoceramics obtained lead to a set of particularities of physical properties.

Jan 1, 2006

By William Bourcier

Geothermal Brines are a significant potential source of valuable minerals and metals. These brines are water that is heated by the natural heat flow from the depths of the earth. Hotter brines, typically with temperatures greater than 120°C, are used to generate electricity. Lower temperature brines are directly used to supply thermal energy to applications such as agriculture, aquaculture and process/domestic heat. The geothermal waters have had intimate and lengthy contact with the layers of the earth?s crust that they flow through, resulting in dissolution of minerals and metals from the rocks, and solution into the hot water. These aqueous solutions can be processed to recover minerals and metals. Some potential products include silica, zinc and lithium, along with other materials. Recovery of minerals and metals from geothermal brines can be viewed as ?solution mining by nature?, followed by application of known or new hydrometallurgical techniques for isolation and purification. This paper discusses the opportunities, the processes, the challenges, the current status, the economics and the potential for recovery of minerals and metals from geothermal brines.

Jan 1, 2006

By Hector M. Henao

There is an increasing trend in the copper smelters to recycle electronic materials, which contain relatively high concentration of precious metals. As a consequence, the amount of precious metals lost in the slag phase is increasing. To determine the portion of the precious metals chemically dissolved and that associated with the mechanically trapped matte in the slag will be a key factor to improve the recovery of those metals. Thus, an experimental study was carried out to determine the distribution of precious metals (Au, Pt, Pd, Rh, Ru) between the equilibrated copper matte and iron-silicate slag phases. The experiments were made in a magnesia crucible at 1573 K and a fixed partial pressure of SO2 of 0.1 atm for the matte grades between 40 and 70 mass% of copper. It was found that the distribution ratios (defined as mass% X in slag/mass% X in matte, where X represents the precious metal) are around 10-2 for Ru, 10-3 for Au, Pt and Pd and 10-4 for Rh. The distribution ratios show a tendency to increase when the grade of matte is increased.

Jan 1, 2006

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By Edgar Blanco

A thermodynamic and experimental investigation to develop a new process for converting molybdenite concentrate to molybdenum dioxide by a water-vapor oxidation process was carried out. In addition, the behavior of rhenium and selenium in molybdenum concentrate during the process was investigated. The kinetics of the reaction were determined by measuring the weight change of a sample with time in water vapor at temperatures between 700-1000°C. The results were analyzed by a Shrinking Unreacted Core model under chemical reaction control, which showed an activation energy value of 102 kJ/mol. To determine the behavior of rhenium and selenium, their concentrations in the molybdenum sulfide and the product molybdenum dioxide were measured by the use of ICP. While most rhenium remained with the molybdenum dioxide after the water vapor oxidation, almost all selenium volatilized. These results agree with thermodynamic analysis.

Jan 1, 2006

By Derek Fray

Molten salts have been used for the extraction of metals since the 19th century but, recently, many interesting processes have been investigated using mixtures of molten salts and different cathodic materials. In several existing processes, the cation is simply discharged from melt but, in some cases, complications arise when the electrode potentials of the cations are relatively close. For example, the co-deposition of sodium with aluminium in the Hall-Heroult process is discussed in terms of electrode potentials of the components in the molten electrolyte. Similar considerations will also be given to the anodic reactions with respect to chlorine, oxygen, carbon dioxide or monoxide evolution from chloride-oxide melts. In some cases, the cathodic product interacts with the cathode to produce new and exciting products such as nanotubes from carbon or titanates and reduced titanium oxides from titanium dioxide. Depending on the electrode potentials, it is also possible to completely change the cathodic reaction from discharge of the cation in the salt to ionisation of the anions in the cathode. Examples are given of the reduction of metal oxides to produce metals, high technology alloys and nanomaterials and the cathodic refining of liquid metals.

Jan 1, 2006

By H. Y. Cho

LS-Nikko Copper Inc, has been operating its Onsan copper smelter since 1979. The smelter began its operation with a designed capacity of 80,000 tpa of copper from concentrates and its smelting capacity was increased to 140,000 tpa of copper by modifying the existing line in 1988. The Mitsubishi Continuous Smelting and Converting Process has been operating since 1998 at the initial capacity of 160,000 tpa of copper. In 2002, the smelting capacity of the Onsan smelter has been increased to 426,000 tpa of copper from concentrate. Now the Onsan smelter has plans to increase its smelting capacity to 500,000 tpa of copper from concentrates by 2010. During the expansion work, the modernization of facilities will be accompanied by an increase in smelting capacity, via the Outokumpu process. This paper reviews the brief history of smelting capacity increase in Onsan smelter and its Outokumpu process modernization plans.

Jan 1, 2006

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006