Search Documents

By Yoshifumi Abe, Akinori Toraiwa

"Nippon Mining & Metals started a new copper anode slime treatment plant that processes slimes in a chloride media. The basic plan of the process was proposed by Mr. James E. Hoffmann and Nippon Mining & Metals modified and advanced to produce precious metals in acceptable qualities for the company. The process has a wet chlorination stage of decopperized slimes, a solvent extraction and a reduction stages of gold, a silver chloride reduction stage and separative reduction stage of its gold extraction raffinate. The new plant of this process started in 1997 and has been operated in good condition.IntroductionThe old anode slime treatment plant of Nippon Mining & Metals, located in it's Hitachi Refinery, processed anode slimes through a combination of pyrometarllurgical processing and electrorefining. There was a need to plan a future of the plant because the maintenance cost increased year by year and a new selenium registration was going to be applied to the plant. Some plans were discussed and the result was that the process proposed by Mr. Hoffmann was superior among them.Nippon Mining & Metals started 'to examine the process and the experimental result showed that the process had an ability to be its new process but further research should be necessary to produce precious metals in acceptable qualities. The final process flow has some modified and additional stages to be suitable for its requirement. Silver processing stage is quite changed. Gold extraction stage has a new step to polish gold loading DBC. Gold extraction raffinate treatment stage is advanced to be able to recover precious metals, selenium and tellurium, separately. Aeration under atmospheric pressure is employed in decopperizing stage.The basic design of the new plant started in 1995 and finished in 1997. The construction of the new plant began in April 1997 and finished in October. The plant has been operating well after the four months test operation."

Jan 1, 2000

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By Olli Järvinen

The capacity of the Outokumpu Pori refinery is today about 125 000 mt in 1998. The anode slime amount is about 700-800 mt. The copper is removed with pressure leaching. Selenium roasting is done with the gas roasting. The doré smelting in the furnace is done with the tilting rotating converter with oxy-fuel burner (TROP). Doré anodes are treated in the silver electrolysis. Gold is recovered from the gold mud with the quick hydrochloric acid leaching process. The important point in the leaching is to get into contact the solid copper with the oxygen and liquid. Outokumpu has an efficient agitator for this purpose. The GLS-agitator (GLS=gas, liquid and solid) is powerful for mixing oxygen, liquid and solid together. The current production in Pori plant is 40000 kg of silver, 5000 kg gold, 40000 kg of selenium and one hundred kilograms of platinum-palladium concentrate.

Jan 1, 2000

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By Kenneth G. Thomas

This paper reviews the alkaline and acid gold autoclaving experiences gained at Barrick Gold Corporation. Alkaline autoclaving was operational at Barrick Mercur, Utah, U.S.A., on carbonaceous/sulphide refractory ore for eight years commencing in 1988. Acid autoclaves have been operational at Barrick Goldstrike, Nevada, U.S.A., on sulphide refractory ore since 1990 and now process 17,500 stpd of ore through six large autoclaves. Information is presented on operating costs, materials of construction, reagent requirements and flow sheet developments that reduced capital and operating costs.

Jan 1, 2000

By Hideki Yamamoto, Junji Shibata

"The chemical reactions of fluoride and chloride gases with metal chloride or metal oxide are utilized as an effective treatment for harmless disposal. These chemical reactions can be adopted in the temperature range of 80°C~400°C, which is lower than that in the combustion treatment (800°C). Reaction products are metal fluoride or metal chloride which are a harmless and a valuable chemical material as one of new resources. This paper, concerns with a new harmless disposal treatment of toxic global warming gases.IntroductionNew technology to make fluoride and chloride gases such as NF3, CF4, SF6 BF3, Cl2 and BCl3 harmless has been developed and a new concept on the removing toxic gas to be used in the advanced process of materials has been established. The fluoride gases ~re toxic and special type of gases to be used in the process of manufacturing semiconductors and their specific applications include the dry etching of semiconductors, cleaning of CVD systems, an oxidation agent for rocket fuel etc. Especially, NF3 is also attracting an attention as a high-energy source for chemical laser systems. As a fluoride gas like NF3 is, however; toxic and highly stable chemically, if discharged into the atmosphere, it is liable to cause far-reaching adverse influences on global warming in the same manner as carbon dioxide gas and feron gas.Up till now, the combustion treatment method has been adopted for the disposal of the gas, and when treating the gas by high-temperature combustion (800""C), the generation of nitrogen oxides (NOx), sulfur oxides (SOx) and hydrogen fluoride (HF) have been confirmed: These chemical substances are not only linked with an intense c0rrosion of the combustion systems but also create the generation of atmospheric pollution and acid rains, and therefore, constitute a serious social issue."

Jan 1, 2000

By J. Vander Linden, R. De Ketelaere, M. Verhaege

In this paper, results are presented concerning the search to implement Supported Liquid Membrane (SLM) technology for the recovery of copper from electroplating effluents. Acid copper electroplating rinse solutions or effluents resulting from the post-treatment of, for example, cyanide-containing copper electroplating baths all contain copper (2+) in the lower concentration levels. A thorough study of the influence of the individual parameters and of their combined impact on mass transfer in small scale laboratory SLM modules has been performed, enabling to set forward the appropriate operating conditions for a pilot plant installation. The pilot plant, containing two SLM modules. of 18 m2 of surface area, has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that this installation is able to treat 40 l/h of acid copper sulphate rinse solutions· containing 500 ppm of copper. The final copper concentration in the effluent can be reduced to a few ppm while copper metal is recovered by electrolysis of the concentrate. This technology is also applicable to the treatment of solutions with low copper content of origins other than plating shops, such as tailings from copper plants or mine waters.

Jan 1, 2000

By Masaru Tomoguchi, Tom Nishiyama, Naoto Sasamoto

"In Hanaoka Mine, which was one of the major ""black ore"" (Kuroko) mines in the north part of Japan, mining has finished in 1994, and only mineral processing plant is available now. Recently this mineral processing plant has been applied to the soil washing. Soils contaminated with heavy metals are excavated and transported to the plant. The soils are separated to cleaned soil and metal enrichment through the process which consists of scrubbing, classification, extraction, insolubilization, flotation, and so on. The process is flexibly designed for each contaminated soil, in order to the products can be recycled as cleaned soils or metal sources. . Soils contaminated with arsenic and lead were treated in 1999, which were entrusted from Environmental Agency of Japan.IntroductionDowa Mining has had the mine site named ""Hanaoka Mine"" and ""Kosaka Mine"" in the north part of Japan. Those mines consisted of some ore deposits and produced ""black ore"" (Kuroko) and ""yellow ore"" (Oko), which are complex sulfide ore. The ""black ore"" mainly consists of sphalerite, galena and barite with accessory chalcopyrite, tetrahedrite and Au, Ag minerals. The ""yellow ore"" mainly consists of powdery and clayey ore containing chalcopyrite and. pyrite, with a little sphalerite and galena. Each mine site had mineral processing plant respectively, ""Hanaoka Mine"" had two and ""Kosaka Mine"" had one plant. Those plants were operated by flotation process to separate each mineral, and produced concentrates of copper, lead, zinc, pyrite, barite and so on.Unfortunately, the mine had closed one by one because of change in economical circumstances and the lack of ore reserves. Mill plants were also closed and dismantled, but the last ""Matsumine mill plant"" of Hanaoka Mine was remained to be utilized usefully. In the circumstance like that, we came across with soil remediation business. Recent reports say that subsurface contamination in Japan is being grown substantially and that it can be a serious matter beyond the imagination of our society. So nowadays we have a tendency to pay attention to the environmental issues including subsurface one."

Jan 1, 2000

By Masayuki Kudoh, Tohru Maruyama, Yohichi. Ito

When hypo-peritectic carbon steel is quenched during unidirectional solidification, the region of fine columnar grain is observed. It is classified into two coexisting phases. One is coexisting phases of liquid, delta and gamma in the upper part of the region, and the other is coexisting phases of delta and gamma in the lower part of the region. To form the coexisting part of the three phases means that solidification in this experiment proceeds in non-equilibrium state. The size of the narrow side of one fine columnar grain coincides with the arm spacing of a primary dendrite and this result is the same as the hyper-peritectic carbon steel. However, the boundary of the fine grain in the hypo-peritectic carbon steel is formed in different location from that of the hyper-peritectic carbon steel. The former is formed in the skeleton of the dendrite, while the latter is formed in the interspacing of the dendrite. The region of the fine grain changes suddenly to that of the coarse grain when the delta phase in the coexisting part of two phases disappears completely. Therefore, the delta phase in the hypo-peritectic carbon steel might prevent the growth of gamma grain. In order to recognize it, ferrite formers such as Mo, V and Ni are added in the sample. Then, the longitudinal length of the fine columnar grain extends in the sequence of the no addition, Mo, V and Nb.

Jan 1, 2000

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By H. Roberts, C. Hassall

The opening years of the new millennium will be characterised by the closure of many lead and zinc mines because of reserve depletion. However, weak commodity prices through the second half of the 1990s have slowed project evaluation and have made it difficult to raise finances for the development of new mines required to replace lost output and to meet increasing demand for metal in the future. Growth of lead and zinc demand will be determined by the pace of global economic activity, especially in the emerging economies. How rapidly demand grows will have a key bearing on the possible shortfall in mine output and the response of prices to the implied tightening of metal supplies early in the new millennium. These issues are the focus of a discussion of the critical lead and zinc supply developments which will unfold post 2000, taking into account project lead times and the role that recycled metal plays in meeting market demand.

Jan 1, 2000

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000