Search Documents

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By M. Cloete, C. MacLagan, A. Newall

This paper initially gives a brief overview of Zinc Corporation of South Africa Limited (Zincor). The original design parameters of the Zincor roasters are compared to the current operation, and the requirements for efficient roasting are listed. Roaster operational problems experienced during the early to mid 1990's are outlined. A description of the investigation and the outcome to increase overall roaster availability are given. The history and the development of the use of oxygen at the Zincor roaster operation, with an account of the associated operational experiences, are explained.

Jan 1, 2000

By M. Giunti, R. Hampson, S. Gray, P. Kapoulitsas, J. Clark

In 1997 Pasminco's Port Pirie Lead Smelter began a modernisation of its lead and precious metals refinery operations. Driven by the anticipated closure of its Broken Hill mine, the new refining process replaced the locally developed continuous process, which had been in operation since the 1950's. Commissioning of the new plant was staged, beginning in late 1997, and finishing early in 1999. The new plant provides for batch refining of lead, and the use of vacuum induction retorting and bottom blown oxygen cupel technology in the silver refining area. The project has resulted in an increase of lead production capacity of 11% and allows the treatment of a wider range of concentrates than was formerly possible. The most significant change has been to double the smelter's silver capacity to over 400 tonnes per annum. This paper describes the successful implementation and optimisation of the new refinery, which is now consistently meeting design capacity.

Jan 1, 2000

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By S. de Vries, B. Wasmund, J. Metric, N. Voerrnann, S. Kasinger

Gulf Chemical & Metallurgical Corporation (GCMC) operates a circular DC electric smelting furnace to treat nickel and cobalt bearing residues at its plant in Freeport, Texas. The furnace, originally built by others, has experienced problems including runouts through the hearth and the lower sidewall. Hatch has designed several improvements to the furnace to alleviate these problems. The single anode at the centre of the hearth was replaced with a patented system of twelve air-cooled copper anodes evenly spaced around the furnace lower sidewall. The DC power supply comprises two transformers and two rectifiers operating in parallel. The water-cooling system on the bottom and lower sidewall shell plates was replaced with an air-cooling system using copper cooling fins. The existing row of water-cooled copper coolers in the metal bath zone was re-designed for greater heat removal capacity and better element joint sealing, and a new row of water-cooled copper coolers was added to cool both the alumina bath and freeboard zones. The existing water-cooled metal and alumina tapblocks were also re-designed for more robust cooling. A binding system was added to provide refractory compression that reduces the risk of liquid leaks. Finally, the furnace tilting frame was relocated to the top of the furnace where it is less likely to be damaged.

Jan 1, 2000

By D. N. Wilson

The potential risks of working with lead have been recognised for centuries, but it is only with the development of sensitive measuring techniques in relatively recent years that it has been possible to establish effective approaches for the monitoring and control of lead exposure. This paper examines the principal control measures employed today - lead in air and lead in blood - and reviews the evolution of numerical standards, with particular reference to the latest understanding of health effects. In addition to lead, a large number of other metals are commonly encountered when producing lead and zinc - both primary and secondary - and the health effects of many of these are discussed. Modern hygiene practices and technologies, which have proved successful in reducing worker exposures, are reviewed. The paper concludes with a look at how exposure standards are likely to change in the near to medium future

Jan 1, 2000

By T. Watanabe, T. Fujiwara, S-Wan Song, Y. Nakagawa, R. Teranishi, M. Yoshimura

"We have tried a new method to fabricate cobalt oxide films onto porous films directly by an electrodeposition method at low temperature. The porous substrate films (membrane-filters and paper) were placed between a LiOH solution and a CoSO4 solution and treated under electricalcurrents of ~1 mA/cm2 using carbon cathode and anode. Effects of temperatures, flow rates and electrical currents have been investigated. As a result, we found that the LiCoO2 films and Co3O4 films were successfully fabricated on paper and/or porous PTFE filters at 120 °C, while CoOOH films were deposited at 80 °C. Furthermore, LiCoO2 films did not cover whole the substrates, but was fabricated just over the anode. The chemical reactions of electrodeposition were also considered from these results.IntroductionRecent agreements on global environment require rapid progress of low energy and low waste processings for the fabrication of thin films that succeed to the mass production with the high consumption of the fossil fuels (such as physical vapor deposition°, chemical vapor deposition2), dip coating with firing3) etc.). The total energy consumption in aqueous systems should be the lowest among all these processing routes, because a much lager excess of energy is necessary to create melts, vapor, gas, or plasma than to form an aqueous solution at the same temperature4)The ""Soft Solution-Process"" (SSP) was one of the best concepts to realize the low energy and low waste fabrication of inorganic materials. 5) Generally speaking, SSP gives similar results to any other processing using fluids (such as vapor, gas plasma) and/or beam/vacuum processing. However, the total energy consumption of all these possessing routes should be the lowest in aqueous systems, because a much larger excess of energy is necessary to create melts, vapor, gas or plasma than to form an aqueous solution at the same temperature (Fig. 1). This idea can be easily demonstrated, using the simple example of BaTiO3. The energy diagram for the formation of BaTiO3 from various precursors is shown in reference 4. The driving forces (AG) for representative synthesis reaction of (1), (2), (3), (4) and(5) are 38, 727, 3685, 17 and —14kcal/mol, respectively at room temperature. 6' 7"

Jan 1, 2000

By G. L. Hundley, D. N. Nilsen

The U.S. Department of Energy investigated the use of liquid-emulsion membranes (LEM) for the selective removal and recovery of metals such as copper and zinc from mine waste waters. This investigation included field tests of a mobile, pilot plant-scale, continuous-flow LEM system. The system was tested at copper mines with solutions containing from 100 to 1,400 ppm Cu, and at a zinc mine with a solution containing 115 ppm Zn. Typical results from the copper tests were >90% copper recovery, and zinc extraction from waste water also was typically>90%. Although all of these waste waters contained high impurity levels, pure products were produced. On several of these field tests, integrated systems were tested that resulted in recovery of metal by-products, selectiv~ precipitation of iron, and polishing to reach discharge targets for essentially all of the contained metals. In addition, some results are included from laboratory-scale tests.

Jan 1, 2000

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

By Tom Lewis

The metal finishing and electronic industries are searching for ways to recycle materials · and reduce costs. The areas of heavy metal waste and water recycling has gained new interests with the potential of impacting the operation's bottom line. Lewis Environmental Services, Inc. has completed numerous heavy metal recovery and effluent recycling projects with its ENVIRO-CLEAN PROCESS for government and private sector clients. This patented process utilizes a proprietary chemically treated granular activated carbon with enhanced heavy metal adsorption capabilities combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA .limits. This paper covers several heavy metal removal projects, two fullcscale commercial installations, and one treatability case study.

Jan 1, 2000

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By M. Okido, O. Takai, Z. Zhao, M. Ishikawa, R. Ichino, K. Kuroda

"Electrolytic method was applied to calcium phosphate coating on titanium plates as an excellent technique for high density and intensive contact of coated films on biomaterials. The effect of H2O 2 as oxidation reagent on coating characteristics was examined to obtain biomineral films. Solution was containing 7.0 X 10·3 mol/dm3 ofCaC12 and 3.0 X 10·2 of Ca(H2PO4)z, kept at 55 ""C. All deposits were hydroxyapatite (HAp) in this study, independent of H2O 2 concentration, applied cathodic potential and solution pH. In the case of H2O 2 addition, an increase in cathode current started at the low potential, namely, ca. -0.2 V (vs. SCE). In contrast, the current increased at more than ca. -1.4 V in the solution without H2O 2 addition. H2O 2 appeared to be an effective reagent for increasing nucleation density and improving adhesion of deposits on titanium plates.IntroductionIn recent years, many researches have been undertaken to develop the techniques of calcium phosphate coating on titanium or bioglass for medical implantation. High density and intensive adhesion of coating are necessary for adding bioaffinity to these materials and for inducing bone morphogenesis on them when implanted in human body.1) Electrolytic deposition has been a newly developed method as high-speed deposition process. By this method, the supersaturation of calcium phosphate can be increased just in the vicinity of metal substrates and the heterogeneous nucleation is promoted on them. In this process, H2O is reduced according to eq. (1) on the cathodically polarized electrode"

Jan 1, 2000

By J. de Visser, J. A. Davis

Since the mid 1970's, development of zinc electrowinning (EW) facilities has out-paced its counterparts in the copper and nickel electrowinning industries in the design of efficient, compact, and automated production plants. Recent advances in process automation have provided opportunities to increase current efficiency, productivity and cathode quality, while reducing the footprint of the plant and the number of operating personnel working on top of the cells. Usually, the practice has been to allow a totally contaminated building structure, combining the plant ventilation system with the process cooling air. As a result, facilities employing this practice are finding difficult to meet their process design criteria and the stringent labor and environmental requirements. This paper provides an overview of the problems and disadvantages associated with these older process designs. It also describes new developments in ventilation systems, particularly building design developments and cost savings that are possible when improved ventilation systems are introduced into efficient process operations. Lead-

Jan 1, 2000

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By Y. Waseda, S. V. Gnyloskurenko

"Present paper reviews the various processes for making of metallic foams. These methods are classified in accordance with the state of initial metals - liquid, powdered and ionized. Liquid metal can be foamed by direct inputting of gas into melt, using gas releasing foaming agents or producing supersaturated metal-gas solutions. This group also includes methods creating voids in the melt. Powder route is based on using powdered matrix metal with foamable precursor materials. Finally Deposition techniques allows making highly porous metallic structures using ionized metal.Experimental study presented shows importance of wettability in bubble formation at gas blowing into melt simulation liquid (water) through holes. Good wettability of injection holes by water ensures formation of bubbles with smaller sizes that effect to the final foam structure.IntroductionOne of the objectives of future production technology is to make of lightweight constructional materials while achieving improved property and good economy as well.The most perspective lightweight materials are cellular or foamed materials that are Wide8pread. in nature and have a growing interest in industry and everyday life.Even metals and metallic alloys can be produced as cellular solids or metal foams beside of the traditional engineering materials such as polymers, ceramics or glass. Recent developments in metal foams, especially aluminium, have produced a new class of lightweight materials."

Jan 1, 2000

By Robert T. Oxnard

"EXECUTIVE SUMMARYThe history of Refractory Recycling indicates there was little recycling until the 1950s. Energy incentives were the primary reason for the beginnings of a recycling effort by the refractory brick manufacturers. Quality benefits quickly became evident and fewer rejects were the result. Today, economic factors including higher valued raw materials and increased competition are the driving forces of refractory recycling.There are some success stories in refractory recycling but we have a long way to go. Few incentives, quality concerns, relatively cheap energy, comparatively lax government regulations, inexpensive landfills and inexpensive substitutes make recycling a difficult choice for many companies. Marketing advantages such as ISO 14000, eliminating multiple audits and reduced liability exposure can tip the scales toward recycling viability. Increasingly, the ideological philosophy of a company, a desire to minimize environmental impact and develop favorable public and other interested party perceptions can drive recycling and waste minimization efforts.Recycled materials can be more trouble ""up front"" and harder to ""manage"" due to their suspect quality. However, due to their nearly inexhaustible supply and the fact that once developed, they constantly contribute to the bottom line, they are certain to be the materials of the future. Waste refractory materials will likely see the same bright future as the steel scrap yards and slag piles of yesterday. In hindsight, we will realize that now was the perfect time to prepare and plan for the bright future of refractory recycling."

Jan 1, 2000

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000