Search Documents

By David B. Dreisinger

The total pressure oxidation treatment of arsenical copper ore and concentrate from the El Indio mine of Banick Gold was tested in benchtop autoclave treatment. The concentrate oxidation typically achieved ~95% copper extraction. Copper extraction was limited by the reprecipitation of a complex precipitate containing arsenic. Gold extraction by cyanidation of the oxidation residue was around 95%. Silver extractions were less than 10% due to the formation of argentojarosite in the autoclave. The total pressure oxidation of the whole ore sample was more successful. Copper extractions of 98-99% were routine achieved. Gold extraction by cyanidation was +95%. Silver extraction could be increased to as high as 95% by using the lime boil treatment. A process flowsheet was proposed based on the results achieved. Copper recovery was proposed by direct solvent extraction and electrowinning of copper by treating the dilute solution from the autoclave discharge.

Jan 1, 1999

By Sue Xue, Carl C. Nesbitt

A project was completed which investigated the efficacy of recycling lead or lead monoxide from various fire assay wastes including crucibles, cupels and slag. The scope of the project was to determine optimal hydrometallurgical parameters so that direct separation and recovery of lead salts was economically feasible. A process was developed from the study which could use either acetic acid or nitric acid as a leachant, followed by several precipitation processes which could directly recover litharge (PbO) or other lead salts, such as lead carbonate or lead sulfate. The economics of the process is discussed. Analytical equipment such as the atomic absorption spectrophotometer and x-ray diffractometer supplied much of the information required for the study. However some novel analytical approaches using these instruments had to be developed to help in the determination of leaching kinetics and process quality control which are discussed.

Jan 1, 1999

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By C. A. Young, J. D. Miller

Adsorption isotherms previously determined by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS) for oleate adsorption at calcite and fluorite surfaces near pH 9 and at various temperatures are compared. Results indicate that, at both mineral surfaces, chemisorption occurs at equilibrium concentrations below approximately l x l0-5 M oleate while calcium dioleate surface precipitation occurs at higher equilibrium oleate concentrations. The extent of chemisorption at the calcite surface is 3 to 5 times less than that at the fluorite surface while the extent of calcium dioleate surface precipitation on calcite is nearly a magnitude larger than that on fluorite. However, for both minerals, surface precipitation decreases with increasing chemisorption. Contact angle measurements and flotation recoveries show the hydrophobicity of fluorite to be greater than that of calcite at each of the temperatures and oleate concentrations studied. Significant differences are noted only in the chemisorption region. Unlike calcite, the hydrophobicity of fluorite was sensitive to the presence of oxygen in the system. Multichannel Laser Raman Spectroscopy (MLRS) showed this behavior was caused by the double-bond reactivity of adjacent chemisorbed oleate molecules and subsequent formation of an epoxide/polyether complex at the fluorite surface. Such a reaction product could not be detected at the calcite surface. These differences in adsorption density, hydrophobicity, and polymerization behavior are discussed in terms of the intrinsic surface properties of the minerals.

Jan 1, 1999

By M. K. Mohan

During the processing of metals like Cu, Ni, Co, large quantities of solutions, which contain co- products such as Sb, Cd, Pb etc. are generated. These solutions if processed to recover the metals help in conservation of metals as well as environment preservation. The present study was taken up to recover antimony from process solutions using zeolites. The effect of pH of the solution, time and type of zeolite viz., chabazite, mordenite, erionite and clinoptilolite on the sorption of antimony was investigated. Rate of sorption increases with pH and about 77-pct. antimony sorption was observed with chabazite at a pH of 6. Optimal conditions were established for the maximum recovery of antimony fiom process solutions. The mechanism of sorption for Sb was proposed in terms of adsorption and intraparticle diffusion. The calculated adsorption constants from Langmuir and Freundlich equations indicated that the adsorption of antimony on chabazite was strong.

Jan 1, 1999

By Sergei A. Degterov

A thermodynamic database for the slag, matte and liquid copper phases in the Cu-Ca-Fe-Pb-Zn-Si-O-S system has been developed for the ranges of compositions of importance to the production of copper. When used with the Gibbs energy minimization software and other databases of the F*A*C*T thermodynamic computing system, this database will permit the calculation of matte-slag-copper-gas phase equilibria that take place during copper smelting and converting. The calculations reproduce within experimental error limits all available experimental data on phase diagrams, activities of components, enthalpies of mixing, matte - alloy miscibility gap and tie-lines. The calculated solubilities of Cu in both S-free slag and slag equilibrated with matte are also in good agreement with experiment under all studied conditions, such as at SiO2 saturation, in equilibrium with Fe, Cu or Cu-Au alloys, at fixed oxygen or SO2 partial pressures and at different contents of Pb, Zn and CaO in the slag. Sulfide contents (sulfide capacities) of the slags are predicted within experimental error limits. The distribution of Pb and Zn among matte, slag, copper and gas has been calculated. The calculations are in good agreement with experimental data and predict the distributions under conditions which are difficult to study experimentally, such as at magnetite saturation or under various oxygen partial pressures and iron to silica ratios in the slag.

Jan 1, 1999

By K. O. Fagerlund

Theoretically and experimentally determined copper matte settling rate in iron silicate slag has been discussed. Separation and settling rate measurements of sand, homogenised slag and 25%Cu concentrate, 63%Cu industrial, and 71%Cu synthetic copper mattes were carried out by mixing crushed slag and matte samples with silica sand in an alumina crucible and melting at 1300-1350°C. Two different types of slag compositions were employed, with Fe/SiO2-ratio 1.4 and 1.7. The separation rate was followed by taking samples from the .melt. As expected, the settling rate of copper matte in fayalite slag depended on the slag composition, where the increasing silica decreased the matte settling rate. Microanalysis of solidified slags showed that the rate of separation of low grade matte was low compared with high grade matte and the presence of a very small size fraction of matte droplets in slag remained unsettled in stagnant fluid. The production of sulfur dioxide gas inside the molten bath was found to be possible up to a certain iron sulfide content in the matte. Also, copper matte settling rates in industrial furnaces have been discussed.

Jan 1, 1999

By P. Ruz

A melt transfer ladle was 3D modeled by means of a mathematical fluid dynamics and heat transfer program. Internal temperature profiles were calculated as a time function for a normal ladle and for a pre-heated refractory lined ladle. It was shown that in a normal ladle the molten metal cools down quickly forming accretions. By using an inner lining there are practically no accretions build up within a typical time of operation. Therefore, by applying a refractory lining to a melt transfer ladle and keeping it at a moderate to high temperature it is possible to reduce cold dope circulation in the smelter.

Jan 1, 1999

By A. H. Castillejos E., F. A. Acosta G.

Filtration is widely used as a terminal refining step for metals, particularly for the casting of aluminum alloys, but still more knowledge is required to understand how several factors affect the efficiency of removal of inclusions. In this study, both, initial and long term filtration efficiencies of a ceramic foam filter have been obtained from the computed trajectories of solid particles suspended in molten aluminum. The complex structure of the foam filters is represented by a unit cell which is formed by a pair of pores with average dimensions. The fluid flow field was determined from the numerical solution of the Navier-Stokes equation, and periodic fully developed flow was assumed at the inlet of the calculation domain, as a boundary condition. This flow field corresponds to laminar flow as that found in ceramic filters operating under normal conditions. Computed initial filtration efficiencies showed that filtration efficiency decreases sharply with fluid velocity for particles larger than 30 µm, but smaller particles are better trapped at higher fluid velocities. Finally, it was found that long term filtration efficiency for particles of 8 µm decreased with time, in spite that perfect particle-wall attachment was assumed. Filter aging was considered in this study, and it was found that the distorted flow field, around the already trapped small inclusions prevented further collection.

Jan 1, 1999

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By P. Barrios

Over a period of one year, an in-depth investigation was carried out in a conventional copper refinery to understand the behaviour of silver in copper electrolysis. The increase in silver content in the cathodes increases almost linearly with the duration of electrolysis, and the silver content of the electrolyte between the electrodes shows similar behaviour. The silver content of the cathode deposited daily depends directly on the silver concentration of the electrolyte and this, in turn, is strongly influenced by its internal temperature. The average temperature between the electrodes rises from the first to the second and to the third crop, because of the increase in the distance between the electrodes and the heat generated by the passage of the current. The mechanism of dissolution of silver from the anode, and its passage to the cathode, are discussed. Following the change to the Isa system, it was proved that the results and conclusions are analogous. Based on these results, a reduction of more than 20% in silver losses in the cathodes was achieved.

Jan 1, 1999

By Arthur G. Hunt

Smelting using the direct-to-blister process commenced at Olympic Dam on 31 July 1988. The unique nature of the Olympic Dam ore body led to the selection of the direct to blister smelting process. Significant improvement in the design of the furnace and the understanding of the fundamentals of the process and its operation has occurred in the 10 years of operation. The paper will discuss the operation of the #1 Smelter and the design, preparation for start up and early operating experience of the #2 Smelter.

Jan 1, 1999

By P. E. Donaldson

Since 1992, Falconbridge has made available to the international copper industry, Kidd Creek's licensed refinery process technology under the name of the Kidd Process. This has resulted in the supply and installation of permanent cathodes and associated product handling equipment to refineries in Canada, the United States, South Korea, Chile and Mexico. These installations accommodate both electrorefining and electrowinning processes. The growth and industrial acceptance of the Kidd Process has generated technical advancements in the areas of product random sampling, corrugation, marking, labeling, product tracking and data acquisition. In a different area, the expanded development of custom materials processing at Kidd created a need to advance technologically. The process-related problem of high nickel concentrations in refinery electrolyte compromised an increase in current density to >300 A/m2. The need for nickel removal resulted in Kidd Creek's newly developed Nickel Recovery System. The effective and economical extraction of nickel, along with reduced antimony and bismuth levels, reduces bleed stream volumes and/or neutralization costs and simultaneously produces a marketable nickel carbonate product.

Jan 1, 1999

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By David J. Kinneberg, Barbara E. Mangion, Arnold M. Savolainen

Analytical laboratories require a qualitative or semi-qualitative method of determining major and minor constituents in "unknown" samples to select optimal analytical techniques. This is exceedingly important in precious metal assay laboratories where the precision and accuracy requirements are exacting (routinely within 0.02%, absolute basis). This paper describes the use of an x-ray fluorescence spectrometer with a specially designed software package to select optimal analytical procedures and specify relevant analytical parameters. A wavelength dispersive XRF spectrometer is capable of quick and accurate analyses of properly prepared samples without extensive standardization. When coupled with a specially designed software package, this preliminary assay system is applicable to a wide variety of sample types including gold and silver bullion, karat gold and karat PGM alloys, high silver and high copper metallic samples as well as particulate samples of ores and sweeps. The system relieves the assayer of tedious calculations for silver inquartation and proofing, minimizes human error and standardizes selections over time. Most importantly, the system allows for independent verification of final assay results.

Jan 1, 1999