Search Documents

By Berndt Moeller

Mercury-cell chlor-alkali production plants generate mercury contaminated wastewater streams from which mercury must be precipitated and filtered, resulting in a sludge containing 2% mercury (designated KI06) that cannot be landfilled in the United States without treatment. REMERC is a chemical treatment process used to recover 99% of the mercury from wastewater sludge generated at these plants. The process uses leaching to oxidize mercury compounds to mercuric chloride, washing and filtration to separate mercuric chloride from the treated sludge, and cementation to reduce the mercuric chloride to metallic mercury. Mercury not recovered in cementation is recycled to the wastewater process for precipitation and filtration. Treated sludge contains less than 260 ppm total mercury and 0.2 ppm TCLP, meeting the USEPA low mercury subcategory specifications that allow landfill disposal. REMERC uses readily available chemicals, is straightforward to control and inexpensive to operate, has no mercury emissions to air, and recovers metallic mercury. REMERC enabled significant cost savings including lower solids disposal costs, recovery and reuse of metallic mercury in the chlor-alkali process, and ability to treat non-wastewater sludge. No new EPA permits were required. REMERC was shown to be a viable process for recovery of metallic mercury from K106 designated sludge.

Jan 1, 2003

By J. Lui

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300?C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination ofH2S and uptake buildup.

Jan 1, 2003

By Irsan Chandra

It is generally recognized that the gold thiosulfate leaching system requires the presence of copper and ammonia in order for acceptable leaching kinetics to be observed. However, the presence of copper and ammonia complicate the chemistry of the system as thiosulfate is rapidly oxidized by oxygen under these conditions. In addition, the environmental impact of ammonia would need to be considered before the adoption of this system. This paper describes fundamental studies into the thiosulfate oxygen system. The two reagents for this system are thiosulfate and oxygen, and leaching is carried out at pH < 7. It will be shown using electrochemical techniques that both the reduction of oxygen and the oxidation of gold-to-gold thiosulfate are hindered. Thus, if leaching is to work under these conditions, then both half reactions need to be improved. The use of additives, such as thiourea and lead have been shown to dramatically improve the oxidation of gold and the reduction of oxygen respectively. The leaching of gold in the presence of such additives is discussed.

Jan 1, 2003

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Akira Nishikawa

During the twentieth century, the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits ofthis approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the S02 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia, limonitic ore from New Caledonia and garnieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potential followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

A full-scale test of chalcocite heap bioleaching was undertaken at Straits? Nifty Copper Operation. Straits worked closely with the CSIRO to investigate the chemical and biological changes over the life cycle of this chalcocite heap bioleach system. Results indicated nearly 80% copper recovery was achieved in just over 300 days. Significant changes in iron chemistry and microbiological activity were detected. Temperatures in the heap reached as high as 70 ºC during the time of maximal copper recovery rate. The dominant cultivatable bacterial strains were typical mesophilic bacteria, however, naturally occurring moderately thermophilic bacteria were detected by culture and culture independent molecular (PCR followed by denaturing gradient electrophoresis [DGGE]) and signature lipid methods. Signatures for the iron and sulfur-oxidising species Acidithiobacillus ferrooxidans and Sulfobacillus spp., as well as the moderately thermophilic heterotroph Alicyclobacillus sp. were detected. Biomass was greatest in ?warm? but not ?hot? parts of the heap, and Hyperthermophilic Archaea were not detected.

Jan 1, 2003

By Terry C. Cheng

The Akita Hematite Process is currently the only hydrometallurgical iron removal process producing saleable iron by-products in the zinc industry. In this study, McGill University and Akita Zinc Co. have worked together into elucidating the basic precipitation chemistry of the process from the standpoints of hematite product quality and prevailing precipitation kinetics. This work determined that hematite is produced under the applied conditions (T = 195?200oC,PO2 = 103?414 kPa) directly without prior formation of basic ferric sulphate and transformation of the latter to hematite as thought originally. The rate-limiting step responsible for the long retention time (~180 min) was found to be either the re-dissolution of ferrous sulphate according to the batch reactor studies, or the slow hydrolysis of the remaining ferric sulphate according to the continuous reactor studies. Another interesting contrast between the batch and continuous reactor data was the degree of sulphur contamination (1.5 vs. 3.8%, respectively) and the specific surface area of the product (10 vs. 30 m2/g, respectively). These differences in addition to the co-precipitation of SO4-containing phases such as jarosites, alunite, and anhydrite were attributed to the significantly higher supersaturation level prevailing in the industrial continuous autoclaves that yields highly aggregated sub-micron hematite crystallites contaminated with chemisorbed sulphate ions.

Jan 1, 2003

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By Gustavo A. Munoz

Activated carbons owe their adsorption capacities to their extensively developed pore network structure. As a result, these adsorbents generally exhibit high specific surface areas. Currently, granular activated carbons produced from coconut shells are traditionally used for gold recovery by adsorption from cyanide leaching solutions. Magnetic activated carbons (MACs) for gold recovery from cyanide solutions produced from sources other than coconut shells have been developed at the University of Utah by mixing a magnetic precursor with a carbon source, and treating the mixture under controlled conditions of temperature and gas phase composition. The pore size distribution of the activated carbons is dependent on the degree of activation, among other factors. The significance of the MAC pore size distribution on gold adsorption kinetics and gold adsorption capacity is presented.

Jan 1, 2003

By Olga Slavkina

A new technology of bacterial leaching by means of the Thiobacillus ferrooxidance bacteria is proposed. The equations of reactions that describe of the first and the second stage of bacterial leaching of sulfide raw materials containing non-ferrous metals are given. The theory is analyzed and the technology of processing of some complicated substandard concentrate containing copper and zinc is proposed. The main technological operations including a two-stage bacterial leaching and stages of copper and zinc recovery in the form of marketable product are described. The results of the experimental validation of the main technological parameters of the first stage are given. The main possibilities of a more complete zinc and copper recovery at the second stage of bacterial leaching are discussed in comparison with single-stage leaching process.

Jan 1, 2003

By Mary Cunningham

The EPA and DOE have collaborated on a series of studies to evaluate the effectiveness of treatment technologies at stabilizing bulk elemental mercury and wastes containing high concentrations (i.e., with greater than 260 mglkg total mercury) and multiple forms of mercury. The data from these treatment demonstrations are intended to help EPA to determine if regulatory revisions to allow a stabilization alternative for high-mercury subcategory wastes are warranted. In addition to mercury-contaminated wastes, the disposal of bulk elemental mercury is of concern because of the excess quantity of mercury in the Defense Logistics Agency (DLA) stockpile, as well as other potential sources of excess elemental mercury. The studies evaluated the effectiveness of several technologies at: I) stabilization of mercury in a "hard-to-treat" matrix; and 2) conversion of elemental mercury into a stable waste form for disposal. A surrogate waste was designed for the study on high-mercury wastes, which included an organic form of mercury, elemental mercury, and several mercury salts in an inorganic matrix. The surrogate waste and the bulk elemental mercury were treated by the vendors, and the treated waste forms evaluated for mercury Icachability, using both the TCLP and an automated, constant-pH leaching protocol. Constant pH leaching was conducted at pH 2,4,6,8 10 and 12 for 14 days at each pH. The leaching data demonstrate that the stability of the mercury in three treated waste forms varies widely across the pH range tested. Clearly, the stability of mercury in these treated waste forms will be highly dependant on the disposal conditions. The combination of site-specific disposal conditions and appropriate treatment technology must be considered as decisions are made about disposal of high-mercury wastes.

Jan 1, 2003

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By David Goodman

The typical operating conditions in Solvent Extraction plants are presented. The various materials of construction used for solvent extraction equipment are reviewed and the history of their use presented. The properties of the materials in common use today, stainless steel, thermoplastics and fiber reinforced plastics, are compared together with cost data. The manufacturing and construction aspects of these materials are discussed.

Jan 1, 2003

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus. The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn304) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6.7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn304 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10-5 m2/s range. The pore size was mainly between 0.1 and 10 um.

Jan 1, 2003

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Katsunori Yamaguchi

A new technique for the removal of tramp-elements from steel scrap has been required from the viewpoint of saving energy and protection of environment. In order to obtain fundamental information on the removal of copper, tin and zinc from molten iron, the extraction method by using of phase separation in the liquid Fe-Pb-C system was investigated at 1453K. A mixture of iron, lead and carbon melted in a carbon crucible separates into two phases of lead and iron containing carbon. The compositions on the miscibility gap in the Fe-Pb-C system are 95.4%Fe-4.5%C-0.1 %Pb and 99.9%Pb-0.I%Fe. The distribution ratios of copper, tin and zinc between the lead and the iron phases, Lx [mass%X in molten Pb]/(mass%X in molten Fe), are 2.2, 2.2 and 1.4, respectively. Seventy percent of copper and tin from iron scrap can be eliminated with comparable lead addition. Gold, silver and palladium are enriched in the lead rich phase, on the contrary platinum and rhodium are more distributed to the iron rich phase than to the lead phase.

Jan 1, 2003

By A. Valenzuela

During the last years, Chile has been the largest copper producer, either as concentrates or cathodes. Copper obtained via pyrometallurgy is produced by seven smelters, which have carried out modernization plans to increase smelting capacity or to achieve environmental regulations established in the Chilean legislation. Thus, the present work updates technological innovations in smelters, environmental regulations and presents solutions for S02 handling, particulate matter and arsenic. Also, the authors emphasize the important role of CODELCO Chile, the most important state-owned copper company, in developing technologies such as El Teniente Converter and El Teniente Slag Cleaning Furnace.

Jan 1, 2003