Search Documents

By Chuanguang Bi, Wenbin Dai, Hongtao Wang, Mansheng Chu, Zhenggen Liu

Coke oven gas (COG) injection is considered as one of feasible measures to reduce carbon emission of BF. The effects of COG injection on the reduction of iron-bearing burdens were numerically simulated by means of multi-fluid BF model, which revealed that with increasing COG injection rate, solid temperature gradually decrease, in-furnace H2 concentration increases, the reduction of magnetite and wustite by H2 is evidently accelerated, the reaction rate of wustite by H2 reduction is enhanced and the reduction degree of mixed burdens is strengthened. Under this hydrogen-enriched condition, metallurgical properties of iron-bearing burdens were experimentally investigated. The GB/T13242-91 test results showed that with increasing COG injection rate, the reduction swelling index of oxidized pellets decreases while the reduction ratio of pellets increases. The softening-melting tests suggested that softening interval of mixed burdens increases from 163.6 to 228.3 °C while melting interval decreases from 147.3 to 92.4 °C. The cohesive zone moves downwards and becomes narrow. The permeability of mixed burdens is improved. In terms of metallurgical properties of iron-bearing burdens, COG injection benefits to improve BF performance.

Mar 1, 2017

By Xiang Li, Merete Tangstad

Currently, the main carbonaceous material for Mn-alloys production is solid carbon, i.e. coke, charcoal and petroleum coke, which is produced with large CO2 emissions. Due to the simple purification, high carbon activity and low CO2 emissions, natural gas has some advantages compared with conventional reducing agents. The aim of the present project is to develop a new technology for production of Mn-alloys using natural gas as a source of carbon. Experimental results indicated that injection of CH4 gas directly into melted slag reduced slightly the MnO and SiO2. However, the metal yield was much less than the theoretical value due to a relative low residence time of CH4 in the slag. The alternative approach was to use carbon black as reductant, produced by CH4 decomposition. The preliminary experimental results showed a high reduction rate using carbon black.

Mar 1, 2017

By Giacobbe Braccio, Alessandro Blasi, Assunta Romanelli, Massimo Morgana, Corradino Sposato

Yttrium is a strategical material for its several usages in a wide range of industrial production. For this reason, improving the recovery of Yttrium has become a crucial focus for international research. In this scientific activity, the utilization of two extractants, 2-ethylhexyl-mono 2-ethylhexyl ester phosphonic acid (P-507) and sec-octylphenoxy acetic acid (CA-12), working in a synergistic extracting system, has been tested. A series of trials have been carried out to optimize the experimental conditions in order to separate yttrium from a mix of heavy rare earths in chloride media. Tests with different relative concentrations of extractants and a phase modifier (TPB, trybutyl phosphate), with different presaponification rate, have been performed to evaluate the behavior of the synergistic system. Results are very promising to recover and separate yttrium with a high purity.

Mar 1, 2017

By Wei Lv, Yang Zhou, Qiang Li, Xuling Chen, Zhiyun Ji, Min Gan, Guojing Wang, Xiaohui Fan

Mineralization during sintering is a process to make part of the raw material melt after serial complex chemical reactions at high temperature. However, high temperature mineralization behavior of the adhesion layer and nucleus particles in the granules during the sintering process has been studied. Research findings reveal that solid-phase reactions between iron ores and fluxes in adhesion layer occurred first, of which the product would induct the generation of the initial liquid phase. By the assimilation of the initial liquid phase, fluxes which served as nucleus particles in granules, such as limestone and dolomite, could dissolve in the liquid phase and extend its amount as increasing temperature, whereas iron ore nuclear particles remained as unfused ores for their insufficient mineralization. Therefore, the mineralization proceeding for sintering was achieved: the iron ores in fine fraction (−0.5 mm) reacted with all fractions of fluxes to form the melt zone, while the coarse iron ores (+0.5 mm) acted as unfused ores, which formed the final sinters together with the melt zone.

Mar 1, 2017

By Xueming Lv, Xuewei Lv, Jie Qiu, Lunwei Wang

Non-isothermal multiple scanning rate analysis method was used to analyse the solid-state reduction of nickel laterite by carbon. According to the TG curves, the activation energies were calculated and the most probable mechanism functions were determined by the Malek method. The results show that the process can be divided into three stages according to the reaction degree (a): 0–40%, 40–70%, 70–100%, respectively. In the stage of 0 a 0.40, the most probable mechanism function fits the chemical reaction order function. In the stage of 0.40 a 0.70 and 0.70 a 1.0, the process may not be exactly described by one mechanism function.

Mar 1, 2017

By Carolina G. D. Ribeiro, Carlos Maurício Vieira, Jordana Ferreira, Sergio N. Monteiro, Janaina da S. Vieira, Cláudio R. Marciano, Natália de O. R. Maciel, Frederico M. Margem

One of today’s biggest concerns has been environmental issues, which has motivated researchers and the development of materials from renewable resources and environmentally friendly. Natural fibers have excelled in replacing synthetic fibers used in composites manufacturing, because natural fibers are biodegradable, abundance in the nature, low cost, low density, high strength, among others. Due to these qualities, some natural fibers are used for many purposes in automobile industry. However, the natural fiber has irregularities and pores in its structure which directly impact the density determination by geometric techniquesand, accordingly, the volume of fibers used in composites. Therefore, the main objective is this study is to determine the density of curaua fiber by pycnometry and to compare it with the commonly used geometric technique.

Mar 1, 2017

By Tracy Morris, Shijie Wang

Preparative Continuous Annular Chromatography, or P-CAC, is an innovative separation technology, a unique approach to high-performance chromatography for the separation of PGM component mixtures from solutions. P-CAC consists of inlet/distribution head and outer/inner cylinders, and bottom plate/fraction-collection as well. P-CAC has been applied in biotechnological and pharmaceutical downstream processing. This was the first time to explore an efficient PGM separation and recovery at the Copper Refinery. Laboratory trials with using a chloride solution for raffination for PGM are described and the tests results are presented in this paper.

Mar 1, 2017

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

Oxidative alkali roasting of chromite is the state-of-the-art process for manufacturing chromium-containing chemicals, which involves dealing with serious environmental problems arising from handling Cr6+-containing wastes generated in this process. In this article a new method for the extraction of Cr2O3 from chromite ores is explained, based on the carbothermic reduction of concentrates in the presence of alkali investigated in the temperature range of 950–1050 °C. Under these conditions, the iron oxides present in the ore body are reduced to metallic iron and the resulting separation of chromium occurs by forming sodium chromite (NaCrO2). The reduced samples are magnetically separated for the recovery of an iron-rich fraction, and a non-magnetic fraction containing NaCrO2, MgO and other impurities. The further treatment of the non-magnetic fraction by leaching yields a Cr2O3-rich product of approximately 85% purity, with remaining alumina, alkali and magnesia. The main advantage of the process is that, under reducing atmosphere and subsequent leaching conditions, the oxidation of Cr3+ to Cr6+ is completely avoided; thereby decreasing the risk of land, air and water pollution.

Mar 1, 2017

By Ying Qin, Shujing Zhu

The characterization of adsorption of natural and composite bentonite in lead aqueous solution has been studied. The results showed that adsorption of both natural and composite bentonites strongly depended on the pH values of the solution. At lower pH values, the mechanisms that govern the adsorption of bentonites were dissolution of crystal structure and competition between the metal ions and the H+. To composite bentonite, the lead ion removal capacity was close to 250 mg/g. At higher pH values, formation of lead hydroxyl species might lead to either participation to the adsorption or precipitation onto the bentonites. Hence, a rapid increase in the equilibrium removal capacity of lead was obtained when pH > 7.0. An increase in the initial lead ion concentration led to the increase in the equilibrium adsorption capacity increased to a certain degree; and then, a plateau was obtained at higher concentrations. As a result, the adsorption performance of composite bentonite was better than the natural bentonite in both physical and chemical changes. The data fitted well with both Langmuir and Freundlich isotherms.

Mar 1, 2017

By Shusen Cheng, Dongdong Zhou, Yongqiang Bai

The strength of sinter could affect the permeability and CO gas utilization of blast furnace, and one of the main impacted factors of sinter strength is crack. With the widely use of vanadium-titanium sinter in China, the blast conditions of some blast furnaces became worse since the vanadium-titanium sinter has been added. However, there have little public research for this phenomenon. In this paper, the influence of titanium content on the sinter ore phase structure and crack were studied by DMRX polarizing microscope. In addition, the influence of basicity and oversintering on the sinter ore phase structure were also investigated. The observed results of vanadium-titanium sinter were compared with typical sinter in China, and the influence law of titanium content on the sinter ore crack was obtained.

Mar 1, 2017

By Neale R. Neelameggham, Ganesan Subramanian

Anthropogenic Heat Flux (AHF) is defined as heat generated from use of non-renewable energy by humans in residential, commercial and industrial activity. State of the art Global Circulation Models (GCM) used to predict global impacts of climate change to help set related policy do not include this heat flux. AHF is considered to be a much smaller an insignificant forcing, solely based on the global mean values. Various Climate models have discussed the “Heat Island Effect ” in high AHF areas. Through the use of simple climate models, it is shown that significant pockets of AHF can impact climate locally in ways significant enough to impact global climate. Inclusion of spatial AHF distribution, rather than a global mean value is important to accurate modeling either on a regional or global scale.

Mar 1, 2017

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By Adriana A. S. Felix, Julio C. Afonso, Luiz C. Bertolino, Bruna L. Novo, Fernanda A. N. G. Silva, Karla M. A. Simões

Palygorskite (Mg,Al)5Si8O20(OH)2(OH2)4.4H2O, is a lamellar mineral with a fibrous morphology. The micropores and canals in the structure give a high specific surface and sorption capacity of various kinds of species. Guadalupe’s palygorskite (Piauí/Brazil) run of mine (ROM) was prepared (PA) and characterized by XRD and XRF. PA is composed by palygorskite, kaolinite, quartz and goethite and has 15.8, 58.0, 4.2 and 7.6% of SiO2, Al2O3, MgO and Fe2O3, respectively. Wet magnetic separation tests were conducted with PA obtaining the magnetic and non-magnetic fractions (PAM and PANM, respectively). PANM was characterized by XRD and XRF and the results of the XRF indicated that the iron content in the PA decreased 8.0% in the non-magnetic product. A new wet sieving was conducted with PANM to obtain a purer fraction (−20 μm) (PANMP) which was characterized by XRD, XRF, CEC, Zeta potential, SEM, TG/DTG. The result showed that this mineral could be used as adsorbent of heavy metals.

Mar 1, 2017

By Mingsheng He, Yunhui Tang

The structure and granularity of biological origin aragonite from abalone shell during wet grinding in a ball mill were studied with X-ray diffractometer, with morphology studied by scanning electron microscope (SEM). It is shown from the results that the particle sizes of aragonite decreased with grinding time, so did the X-ray diffraction (XRD) peak intensities, while the full widths at half maximum increased. A calcite XRD peak with low intensity and great width was observed in nearly all the samples with various grinding time, whereas the intensity of the peak increased obviously after grinding time 300 min. It is shown from the SEM results that the size of aragonite dropped with grinding time until it reached 20 nm and then kept constant, while that of calcite dropped first and then rose at the minimum about 10 nm until to the constant size as in aragonite. It was observed that the mineral content obtained from XRD show an obviously change that the calcite increases while aragonite decreases, which indicated the occurring of a polymorphic transformation of aragonite into calcite.

Mar 1, 2017

By Shusen Cheng, Kun Yan

An elastic-plastic stress mathematical model of hot blast stove shell has been established in order to investigate the stress distribution and deformation of the shell. The results show that stress concentration happens along the intersection line of hot blast stove body and the hot blast manifold. The plastic deformation occurs on the hot blast outlet in blast period. The deformation degree of the hot blast shell near the blast outlet in blast period is much larger than that in combustion period. In blast period, the shell near the blast outlet elongates along the horizontal direction and shortens along the vertical direction, the shell near the outlet deforms into an oval. And in combustion period, its deformation isn’t obvious. The repeated deformation of the shell near the outlet between different periods may cause the refractory brick damage and be harmful to the long campaign life of hot blast stove.

Mar 1, 2017

By Jianguo Yin, Xuejiao Zhou, Xiaoyan Xiang, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade phosphorus-containing iron ore (LGPIO), a raw and wasted industrial solid material was used as an adsorbent to remove Cd(II) ion from wastewater. The effects of initial pH value, adsorptive time, initial Cd(II) ion concentration, adsorptive temperature and LGPIO dosage on the Cd(II) ion removal efficiency were studied. The results show that the Cd(II) ion removal efficiencies exceed 99.8% and Cd(II) ion concentrations are less than 0.10 mg/L under the pH value 6, temperature 20 °C, adsorptive time 90 min, initial Cd(II) ion concentration 50 mg/L, particle size <0.15 mm, adsorbent dosage 50 g/L and stirring speed 290 r/min. After Cd(II) ion removal reaction, the Cd(II) ion concentrations completely complies with the requirement of national discharge standard of water pollutants for cadmium and zinc industry (GB 20466-2010) (TCd(II) = 0.1 mg/L) in China. Therefore, it can be concluded that LGPIO is a new low-cost adsorbent which is suitable for the adsorption of Cd(II) ion from wastewater.

Mar 1, 2017

By Seref Sonmez, Onuralp Yücel, Kagan Benzeşik

The aim of this study is processing of domestic molybdenum concentrate to produce technical grade molybdenum trioxide may be the starting material for the production of various molybdenum products. In order to determine the optimum parameters for the total oxidizing roasting process of molybdenite concentrate to produce MoO3 and purify the MoO3 product by removing the copper content; first, MoS2 was roasted by controlling reaction temperature and duration in a chamber type furnace. The highest Mo concentration rate was obtained as 56.6 wt% of Mo at 650 °C for the roasting duration of 45 min. Secondly, roasted product was leached with H2SO4 to remove copper. Leaching conditions were optimized by investigating the effects of different H2SO4 concentrations and S/L ratios. The minimum copper content was obtained as 0.13 wt% at leach residue. The raw materials and the products were characterized by using AAS (atomic absorption spectrometry) and XRD (X-Ray Diffraction) techniques.

Mar 1, 2017

By Wolfgang Koch, Bernd Friedrich, Ann-Kathrin Maurell-Lopez

Due to the high standards for silver in electronic uses, it is essential to control the behavior of the main impurities such as copper or palladium during electrolytic refining. In regard to palladium, it is indispensable to understand and manage its co-deposition behavior. The influence of electrolyte composition, current density, and acid concentration on Cu and Pd co-deposition during silver electrorefining is systematically investigated.

Mar 1, 2017

By H. Y. Sohn, Y. Mohassab, D. -Q. Fan, M. Elzohiery, A. Abdelghany

The Flash Ironmaking Technology being developed at the University of Utah is aimed at producing iron directly from iron oxide concentrate. In this technology, the concentrate is reduced by H2 and CO gas mixtures formed from the partial oxidation of natural gas in a flash reactor. Natural gas represents an economically and environmentally superior reductant/fuel for the flash ironmaking. The rate equations for the reduction kinetics by H2, CO and H2 + CO gas mixtures were determined in the temperature range 1150–1600 °C. These rate equations were applied to experimental results from a laboratory flash reactor using Computational Fluid Dynamics CFD simulation. A new mini-pilot reactor, which is capable of operating at 1150–1550 °C with a concentrate feeding rate of 2–5 kg/h, has been installed. Commissioning of the reactor with an emphasis on preheating of the reactor, production of reducing gas mixtures and the feeding and collection of iron ore concentrate and product particles has been completed.

Mar 1, 2017

By Luane Isquierdo Ferreira Holanda, Lucio Fabio Cassiano Nascimento, Luis Henrique Leme Louro, Sérgio Neves Monteiro, Alaelson Vieira Gomes, Édio Pereira Lima Júnior

In the present study,we used natural fibers malva (Urenalobata, Linn) in 0, 15 and 30 vol.% as reinforcement of epoxy matrix composites to ballistic application. Ballistic efficiency of these composites was assessed by measuring the energy absorbed and residual velocity after impact 9 mm FMJ ammunition projectile, aiming to compare with traditional materials, such as: aramid fabric Kevlar™ used in vests for personal protection. The results showed by visual analysis and scanning electron microscopy (SEM) that the main active failure mechanisms in composites were delamination layers and fiber rupture. In test groups can be seen that the absorbed energy and the residual velocity varies with the fiber percentage used. Compared to aramid there is both a gain in weight and cost of the ballistic armor, which makes the fiber malva a promising material applications involving personal protection against 9 mm caliber ammunition.

Mar 1, 2017