Search Documents

By De-qing Zhu, Feng Zhang, Jian Pan

Sintering performance of a series of sinter blends with high ratio of limonite was investigated. The metallurgical performance and mineralogy of product sinter were also examined. The results show that good sintering performance could be obtained when the ratio of limonite was below 43% in the blends of iron ore fines, while good microstructure and metallurgical properties were achieved under optimum sintering conditions. In contrast, sintering performance will rapidly deteriorate when the ratio of limonite is elevated up to 63% in the blends.

Mar 1, 2017

By Sarel Johannes Francois Gates, Ida Kero, Yan Ma, Gabriella Tranell

During the tapping and casting of manganese ferroalloys, fumes are generated and released to the working environment. The fumes are mostly composed of metallic oxides generated due to reaction between high temperature molten metal and ambient oxygen in the air. From an environment perspective, it is important to limit these emissions. However, to do so, it is important to understand fuming mechanisms and kinetics as well as fume compositions, i.e. element behavior during the oxidation process of liquid manganese ferroalloys. Silicomanganese alloys are composed of aminimum of 65 wt% Mn and 17 wt% Si, 2 wt% C as well as minor and trace elements. These elements include Fe, Mg, Al and other elements originating from ores and reductants. Trace elements behavior in fume from liquid silicomanganese generated under an impinging air jet in the temperature range of 1450–1700 °C has been investigated in this work. The thermodynamic and kinetic conditions governing the generation mechanisms are discussed.

Mar 1, 2017

By Christine Wenzl, Christoph Wagner, Christoph Sagadin, Stefan Luidold

Corrosion mechanisms have been investigated between MgO refractory substrates and synthetic FeNi slags. The materials taken into consideration comprised a simple synthetically mixed slag with specific oxides of slags from a ferroalloy producer. The MgO refractory substrates with the slag specimens on it were heated in a hot stage microscope to two different characteristic temperatures, 1350 and 1650 °C. The experiments proceeded under a controlled gas atmosphere that simulates the relevant process conditions. The corrosion mechanisms of each system were determined by SEM analyses. The obtained results showed that slag corrosion is dominating with a pronounced partial dissolution of refractory. It was also observed that iron oxide present in the slag diffused into the coarse refractory grains forming the relative low melting magnesia wuestite. Finally,the comparison of these findings with those predicted by thermodynamic calculation (FactSage) indicated the corrosion mechanisms and draw implications for improving the refractory performance and lifetime.

Mar 1, 2017

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017

By B. J. Zhao, F. L. Han, L. E. Wu, M. Chen, Y. H. Chen

Magnesium is the lightest structural metal with a density only two-thirds of aluminium and one-quarter of steel. It can be produced by electrolysis of fused magnesium chloride or high temperature reduction of the oxide. The predominant method for magnesium production is the Pidgeon process which is a batch process starting from calcined dolomite and ferrosilicon. CaF2 is commonly used in the process as the catalyst. Analyses of the slag samples and thermodynamic calculations indicated that liquid phase plays important role in the reduction process. Effects of chemistry, temperature and gas pressure on the production have been discussed and compared with the operating data. Understanding of the reaction mechanisms will provide a fundamental base for alternative processes of the magnesium production.

Mar 1, 2017

By R. H. Eric, A. Chaendera

Gas jet was blown through bottom nozzles of a 1/5th scale CLU model in the presence and absence of slag. Kerosene and water were used to simulate the slag and metal phases respectively. Mixing time increased with increasing bath height and with a decrease in the gas flow rate. It was related to bath weight, bath height and gas flow rate. Slag increased mixing time by about 16% and the mass transfer values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with increasing gas flow rate and with a decrease in bath height. A relationship showing the dependence of derived mass transfer coef ficient on the gas injection rate was established. Turbulence characteristics inside the bath liquid were established to vary with location, vessel geometry and gas injection rate.

Mar 1, 2017

By Yu-ki Taninouchi, Toru H. Okabe

Among platinum group metals (PGMs), Pt, Pd, and Rh are the essential constituents of automotive catalysts. Recovery of PGMs from catalyst scrap is important, but it is difficult because PGMs are chemically stable and are present as minor components in the scrap. A vapor treatment method using FeCl2 vapor to alloy PGMs with iron, enabling subsequent magnetic separation, is developed and tested on Pt, Pd, and Rh wires.

Mar 1, 2017

By Han Yihua, Zhang Caijun, Zhu Liguang, Zhang Qingjun, Wang Shuoming, Wang Yan

An industrial test on 210 t converter-LF-CC production line on high heat input welding shipbuilding structure steel DH36 has been taken in a factory in north China, the effect of adding microalloy elements V and Mg on casting billet microstructure has been researched. It was found that when the composition of V was between 0.03 and 0.05% and the composition of Mg was between 0.002 and 0.005%, a large number of acicular ferrite precipitate in austenitic crystal in as-cast structure and cross into a net structure. The inclusions size which induced intra-granular ferrite are mainly less than 4 lm, especially those between 2 and 3 lm account for 50.80%, in these inclusions the composite inclusions mixed with Mg accounted for more than 60%.

Mar 1, 2017

By Chen-Ming Kuo, Esher Hsu

Energy recovery of livestock waste can not only reduce waste pollution but also generate renewable energy and further create economic bene fits. Currently, most of livestock waste in Taiwan is treated as waste without efficiently recycled. This paper aims to explore and evaluate the energy recovery of livestock waste in Taiwan and further provide policy suggestions. Study results show that small farming scale of livestock industry in Taiwan leads to a lower efficiency of biogas energy recovery. Besides, the environment with relative low price of electricity and high invest cost for power generation plant is hard to provide incentive for implementation of energy recovery which has further caused difficulty on policy promotion for renewable energy recovery of livestock waste in Taiwan. Policy reform with increasing FITs and differentiated purchasing rate for biogas power is suggested to stimulate energy recycling of livestock waste in Taiwan.

Mar 1, 2017

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

The wettability behavior of graphite with silicon is a key factor for its application as a crucible in silicon making industry. A previous study was carried out to determine the correlation between the physico-chemical behaviors of different types of graphite and the final contact angle for the graphite/silicon system. In this study, experimental vacuum annealing treatment by varying the exposure time at high temperature of 1000 °C processed by X-ray photoelectron spectroscopy and SEM analyses enabled to found a correlation between the oxygen content in the graphite and the final contact angle for the graphite/silicon system. Finally, the experimental results with and without vacuum annealing treatment have shown that a deep infiltration of silicon inside the graphite occurs in case of high level of oxygen content inside the graphite’s pores.

Mar 1, 2017

By C. Hakan Gür

Optimization and control of the microstructure is important for improving the properties of steel components. Development of non-destructive techniques for microstructure characterization is a critical task. Magnetic Barkhausen Noise (MBN) technique is a promising and challenging non-destructive technique fo automated evaluation of microstructures in steel components in a fast and reliable manner. This paper presents the results of MBN measurements for microstructure characterization of the quenched and tempered steels.

Mar 1, 2017

By G. Djambazov, V. Bojarevics, K. Pericleous

The AC electromagnetic (EM) field effects are investigated for the possibility to extract particles (impurities, precipitates, oxides, bubbles, etc.) from molten silicon during the directional solidification of silicon ingot. The dynamics of particles are affected by the hydrodynamic drag, buoyancy, turbulent fluctuations and the EM force via the local pressure distribution. The EM force leads to high mixing rates, transitional flow structures and turbulence of the melt, contributing to the particle dispersion, transport and separation to a desired location. Application to silicon kerf loss recycling by melting and solidifying in the presence of AC EM field is presented for a variety of cases using 3D models for general flow structure and axisymmetric models for moving solidification front long time tracking. This paper demonstrates the effects of flow on the time dependent particle ‘swarm’ transport and the eventual modified distribution in the final ingot.

Mar 1, 2017

By Abdulkader M. Abed, Shadia J. Ikhmayies, Bothina M. Hamad, Belal S. Amireh, Yulia Valery Meteleva

This work is a first step on the way to characterize raw sandstone in Jordan, and to extract silica and silicon for the use in solar cells and other industries. Seven samples of raw sandstone were brought from Disi in Jordan. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray fluorescence (XRF). The XRD diffractograms showed that silica is the main constituent of the samples, and two samples contain Kaolinite Al2(Si2O5)(OH)4. EDS reports showed that all samples contain aluminum and carbon, but some of them contain calcium. XRF measurements revealed that some samples contain more than 97% silica, while one sample contains more than 90% silica, and the main impurity is Al2O3. FTIR revealed the known bands of silica, and this sandstone is free of organic compounds impurities.

Mar 1, 2017

By Felix Wolters, Michael Schütt

In over 40 years of operation, engineers at Aluminium Oxid Stade GmbH (AOS) have acquired a lot of experience whereby they have developed a series of optimizations regarding the specific primary energy consumption. The tube digester technology, invented by VAW in Germany and applied on an industrial scale for the first time in Stade, was brought to perfection by its innovative cleaning methods, which led to a constantly high heat transfer, low pressure loss and excellent availability of the digesters. Further improvements such as the heat recovery from the exhaust gas stream of the salt heater as well as the optimization of one of the fluid bed calciners and the installation of a combined heat and power generator (CHP) led AOS to where it is now—a leading alumina refinery with regard to the lowest energy consumption per ton of alumina.

Mar 1, 2017

By Xun Zhang, Huiqing Tang

The inner shape of a blast furnace is of fundamental importance for blast furnace ironmaking to achieve goals of high yield, high quality, low fuel rate and long campaign life. Therefore, it is worthwhile to design better furnace inner shapes. This paper conducted numerical simulations of performance for the blast furnaces with conventional and modified inner shapes. By comparing the calculation results of the two blast furnaces with the same operation conditions, it can be found that there are some certain differences. It is necessary to optimize the inner shape of blast furnace considering the results of simulations. This paper provides references for future blast furnace inner shape design and related technology developments.

Mar 1, 2017

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

The present status of wastewater advanced treatment and reuse in iron and steel enterprise is discussed, and the membrane technology used in wastewater advanced treatment and reuse from iron and steel enterprise was investigated. Its advantages, disadvantages and the development tendency were discussed and some advice and prospects of membrane technology for the reuse of wastewater treatment in iron and steel enterprise were pointed out.

Mar 1, 2017

By Wenxuan Xu, Shusen Cheng, Tian Chen

Pulverized coal injection (PCI) can generate heat and reducing gas in the raceway and replace some expensive metallurgical coke in the blast furnace ironmaking process. In this paper, a three dimensional mathematical model of the raceway including the coke bed has been developed to simulate the complicated phenomena of pulverized coal injection. The effects of oxygen enrichment, particle diameter in the raceway are investigated in this study. The establishment of the 3D model is expected to analyze the raceway working state accurately and optimising the PCI operation of blast furnaces.

Mar 1, 2017

By Zeyun Cai, Gaoyang Song, Bo Song, Yuhou Yang

In this research, super gravity field was introduced in the solidification process of high carbon steel. The experimental results show that the solidification structure of Fe–1 wt% C steel can be largely refined by applying super gravity at the cooling rate of 10 °C/min. Both the primary and secondary dendrite length was markedly reduced. In addition, the eutectic structure in the inter-dendrite was also refined with the obvious reduce of eutectic space. However, the macro-segregation of C along the direction of super gravity was caused with higher weight percent at the upper area than that at the bottom of the sample. The mechanism of solidification structure refinement and the C macro-segregation of Fe–1 wt% C steel in super gravity field were also discussed in this paper.

Mar 1, 2017

By M. G. Silva-Valenzuela, A. T. Machado, F. M. S. Carvalho, J. R. Matos, A. A. S. Araujo

Electric arc furnace steel dust is a by-product of the steelmaking process and contains high amounts of iron and zinc and significant amounts of lead, chromium, and cadmium and others chemical compounds in minor proportion. However, the material recycling is very complex, mainly due to their mineralogical composition. In this study the characterization and application of this material is presented. Ceramics were produced with clay and variable amounts of steel dust. Th bulk material was fired between 800 and 1000 °C. The influence to insertion of this material on the ceramic composition on the mechanical strength, linear shrinkage, water absorption, apparent density and bending strength of the ceramic samples was investigated. A blend of clay with 5% dus presents potential for use in structural ceramics production.

Mar 1, 2017

By M. A. Kader, M. A. Islam, P. J. Hazell, M. Saadatfar, J. P. Escobedo, A. D. Brown

The dynamic pore collapse mechanisms and energy absorption capacity of closed-cell aluminium foams subjected to low velocity impacts have been investigated. Impact experiments were carried out using an instrumented drop-tower with two impactor geometries: a 50 mm square flat steel impactor to investigate pore collapse mechanisms and a 20 mm diameter hemispherical steel impactortostudy indentation resistance.X-ray computedtomography was utilized to generate views of the deformation field within the impacted specimen. The results show that the strain rate and incident impact energy influence the energy absorption capacities of closed-cell aluminium foams. Furthermore, damage initiation, propagation and cell collapse mechanisms under drop weight impact have been elucidated.

Mar 1, 2017