Search Documents

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world's Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company's outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world's Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

Comprehensive occupational health and safety legislation in Australia is comparatively recent. It follows the examples set in U.S.A. and U.K. a decade or more ago. In Western Australia the Occupational Health, Safety and Welfare Act was proclaimed in April 1985. It still has a long way to go before it achieves all its objectives. The mining industry has developed a substantial body of health and safety regulations under the Mines Regulation Act. Considerable practical expertise in such matters already exists, much of it developed from hard won experience. As a result it would prefer not to become engulfed in the new legislation. It would prefer to build upon the cooperatively developed policies and workable practices in the field of occupational health and safety with which it is familiar. Associated Minerals Consolidated Ltd. is a leading mineral sands producer in Western Australia and has continuously developed its occupational health and safety policy and practices. Under the banner of "Resource Control", AMC seeks to provide a safe and healthy working environment at all times. This is being achieved through a strategy of a policy, a defined organisational structure and a detailed programme, which together comprise the "Resource Control System". Some of the activities and achievements of AMC in the field of occupational health and safety are compared with the objectives of contemporary legislation, and details of some of the specialised areas of the Resource Control Programme are discussed. The paper will also highlight and discuss impractical areas of potential legislation.

Jan 1, 1986

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

Spectrum Resources commenced operations as a public listed mining company in August, 1983, with a variety of precious metal projects in New Zealand. At that time the outlook for most mineral commodities, with the notable exception of precious metals, was decidedly gloomy. Metal prices were depressed and demand forecasts were universally gloomy. Against this background the company reviewed the non-traditional metals sector to try and identify a 'new' metal with an above average demand growth and market value. Lithium, a commodity with exciting new applications in storage batteries and alloys, met both criteria. Annual world consumption of lithium is around 7000 tonnes; current prices are around $NZ40/lb for lithium metal and demand growth is projected at five to seven per cent per annum. Geothermal fluids at Wairakei and elsewhere contain anomalous amounts of lithium and in May, 1984, the Chemistry Division of DSIR was commissioned to carry out a literature survey on the possible recovery of lithium and other minerals from geothermal waters. The survey results were encouraging and the company subsequently negotiated exclusive access rights, for research purposes, to geothermal discharge fluids from the Wairakei and Kawerau geothermal fluids. Most of the subsequent investigations reported here were carried out by Chemistry Division, DSIR, under contract to the company with some assistance from the Industrial Processing Division, DSIR.

Jan 1, 1986

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By J. K. Ahlness

The Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 225 ft (69 m) were tested at an average rate of four wells per 8-h shift with a two-person operating crew. This represents a 75-pct time savings and an 83-pct labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1986

By Charles Kimbell, L. Nahai, E. Shekarchi

INTRODUCTION AND SUMMARY World mineral trade during 1960 to 1984 has shown substantial changes both in value and tonnage. Although fuel commodities dominated total mineral trade during this period, this paper will focus attention primarily on nonfuel minerals. Brazil and Australia, modest producers of iron ore in 1960, have become dominant producers and exporters, together accounting for about half of major iron ore exports in 1984, far surpassing traditional export suppliers such as Sweden. Australia has also become the largest producer and trader of bauxite and alumina, and worldwide alumina trade has increased at the expense of bauxite trade. Similarly, shipments of ferroalloys have increased more than shipments of ores such as those of chromium and manganese. Canada, retaining its first rank in world export of zinc, has become also the leading source of potash and sulfur in world trade, and South Africa has been the dominant factor in chromite, manganese and their respective ferroalloys. Developing countries' share of world copper trade has increased, with Chile maintaining first rank, but developed industrialized countries have continued to dominate production and trade of lead and zinc. Phosphate, sulfur, and potash have been the principal crude nonmetallic minerals traded worldwide. Looking to the near future, dramatic increases in export of iron ore, phosphate, potash and sulfur are not envisaged. Bauxite exports will continue to decline relative to alumina but at a slower rate than in the recent past. Zinc concentrate will continue to be exported but lead will be traded more as metal than as concentrate. For iron and steel, there will be some production shift from traditional producers to certain developing countries and recently industrializing developing countries such as Brazil, India, the Republic of Korea, and Taiwan. In the following sections dealing with specific commodities, it should be understood that information is presented only on the major forms of each commodity that move in trade, and only for a selected group of countries for each commodity or major form of each commodity. Thus, totals shown or mentioned generally represent only the totals of figures presented here and do not include estimates for minor forms of material or for countries that are not listed. However, the data provided is regarded as sufficiently complete to reflect major patterns and trends, and exclusions are there- fore not seen as affecting conclusions that may be drawn from the material provided. FUEL AND NONFUEL TRADE Values of Fuel and Nonfuel Trade The value of world export trade in major mineral commodities (ores, concentrates and scrap, crude minerals, iron and steel, nonferrous metals, nonmetallic minerals and mineral fuels) in 1983, the latest year for which comprehensive data are available, was reported by the United Nations in May 1985 to have totaled over 514 billion current U.S. dollars (Table 1). This was 79% of the historic record high of nearly $649 billion ,current dollars set in 1980, but almost 18 times the current dollar value reported for 1960. [1/] The value of these 1983 exports in constant 1960 dollars was $164 billion (Table 2), only 66% of the record 1980 high of almost $250 billion, and only about 5.7 times the 1960 dollar level.

Jan 1, 1986

By Clayton M. Rumsey

The U.S. Bureau of Mines investigated prospects and mineralized areas in and adjacent to the Indian Pass and Picacho Peak study areas in 1983 and 1984. The Indian Pass study area contains 33,640 acres and the Picacho Peak study area contains 5,450 acres. The study areas are located in the southeast corner of California and are underlain by Precambrian gneiss, Pre-Tertiary metavolcanic and metasedimentary rocks, and Tertiary volcanic and non-marine clastic rocks. Low-grade gold-silver resources may be present in hydrothermally altered gneiss in the upper plate and altered schist in the lower plate of the Chocolate Mountain thrust fault. The thrust fault is exposed in the study areas for about 3.5 miles west and 5 miles east of Indian Pass. Mineralized zones in the thrust plates were not discovered until 1983. Earlier prospecting explored areas containing minor copper carbonate occurrences in schist and sedimentary and volcanic rocks that are younger than the thrust. Twenty-three mines, prospects, and mineral occurrences inside the study areas and fourteen outs; de were examined for this study. These surficial copper occurrences have been prospected extensively in the study areas; large areas have been scraped, pitted, and trenched by bulldozers. However, they appear to be of limited economic significance. Slightly mineralized zones are in the northwest part of the Indian Pass study area where granite contacts sedimentary and volcanic rocks.

Jan 1, 1986

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986

This opportunity to present a few thoughts on the question of professional education and training comes at a most appropriate time. In Britain, a great deal of energy is being expended in this, so-called, post-Finniston era, to create a new look for the status of engineers and engineering by the Engineering Council. Naturally, the tune and the tempo are being called by the big institutions which essentially serve the manufacturing industries. However, the Engineering Council in Great Britain also includes the mining and processing institutions such as the Institution of Mining and Metallurgy (IMM) and so there is a chance - if it is taken - for us to contribute to the debate and the determinations that emanate from it. The IMM, of course, caters for the professional status of those engaged in the mining and minerals industries and includes many who do not see themselves as engineers. Nevertheless, the debate is important to these other groups whose livelihood is inextricably bound up with those who are engineers and there are many facets of the engineering policies being shaped that will, I am sure, eventually be enshrined in the requirements for professional status across all the various disciplines in our industry.

Jan 1, 1986

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

Jan 1, 1986

By Brown N. R

This paper attempts to highlight some of the problems encountered in the economic exploitation of the deeper coal seams by opencast mining methods. The major cost elements of three methods of overburden removal are examined in relation to the overall cost of winning coal from deeper-lying coal seams. The three overburden removal methods examined are dragline stripping and two systems combining dragline stripping with shovels and trucks at varying depths of overburden. A dragline is, undoubtedly, the most cost effective system of overburden removal for depths of up to 30 metres but it is suggested that, when dealing with incremental overburden depths in excess of 30 metres, engineers should consider carefully the possibility of using a shovel and truck operation, or other system, to augment the use of a dragline.

Jan 1, 1986

By I. W. Farmer, R. E. Finky

Design of structures in rock based on ultimate limit states or strength criteria is unrealistic. The fracture process which inevitably occurs in rock around an underground structure is an energy release phenomenon. The development of fractures and associated displacements around a structure may therefore be more logically described using strain energy concepts and design may sensibly be based on serviceability limit states.

Jan 1, 1986

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986

The gold industry has been revolutionized in the last decade by market forces and technological changes. The latter are discussed in this paper, with particular emphasis on carbon-in-pulp (CIP) and heap leaching. The nature and scope of the process development aspects of a gold project are considered, and factors which determine process decisions are outlined, including the choice of CIP versus carbon-in-leach (CIL), agitated leaching versus heap leaching and treatment of ores containing copper and silver. Likely directions for development of gold processing in general are discussed, and metallurgical process options for treatment of ores of platinum group metals (PGM) are outlined.Metallurgical process development for gold and platinum group metals proceeds through a number of well defined stages, with input from various disciplines and information sources. The orientation phase will include preparation of a general project overview; careful consideration of the issue of sampling and sample preparation; characterisation of the resource in terms of ore types, mineralogy, chemical composition; development of appropriate methodology; and development of an understanding of the potential metallurgical unit operations.The process definition phase will be-'directed to development and definition of a notional process flowsheet, and will include identification and appraisal of process options; development of, notional process flowsheets; testing of flowsheets against ore types; ranking of flowsheets; initial engineering, including preliminary mass balances, equipment selection and plant layout; and broad-brush economic appraisal.

Jan 1, 1986

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986

By Wang Zuoyu

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies to the time of the Symposium.

Jan 1, 1986

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986