Search Documents

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By Eduardo Gonzalez Fernandez, Jaime Rios Vazquez

This report substantiates the connection that always exists between explosives and vibrations and draws attention to low frequency vibrations, which are the moat dangerous for the structures affected.

Jan 1, 1986

By D. J. Shields

This paper describes a dynamic short-nun mineral supply model that incorporates secondary processing, transportation, mineral market structure, and direct mining and milling costs. The method employed is network flow programming. Empirical tests utilizing domestic phosphate industry data have been conducted by the Bureau of Mines, U.S. Department of the Interior. In the model, nodes represent physical locations such as a mine or port. Arcs represent either a process, such as mining, or movement, such as rail or barge transport. Each arc is described by lower or minims allowable flow bounds, upper or maximum possible flow bands, and variable cost. Mines and previous period inventories represent potential supply. The model is optimized via a cost minimizing algorithm, which attempts to fulfill stated total demand at the minimum possible system cost given the arc constraints. An optimal solution of the model will predict production patterns by mineral property for each prespecified level of demand. A mineral property is defined as a separate accounting entity such as a mine. The results of serial optimizations are used to construct the short-run supply curve. Dynamic policy analysis can be conducted by altering the arc constraints.

Jan 1, 1986

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

Reduce injury to people or damage to equipment when a scheduled production blast is detonated. Approach The essential elements of an effective blast area security system were identified through case studies of five mining operations where the blast area guarding practices were considered to be superior to those generally found in the industry. These elements were used in making recommendations for improved blast area safeguarding practices. Background The blast area security system is a means by which the mine operator prevents injury to people or damage to equipment when blasting is performed. Analysis of blasting accidents showed that most blasting accidents occur during scheduled blasting and are due to inadequate blast-site security. Factors contributing to the system's breakdown are failure to clear the blast zone, inadequate guarding. and failure of personnel to follow instructions, retreat to a safe location, and/or take adequate cover. Mine personnel, visitors and even trespassers can inadvertently wander into a blasting zone unless proper procedures exist to ensure that all personnel are cleared from the blast zone and kept safely away until after blasting IS completed. Statistics show that the blaster is the miner most frequently injured In these accidents.

Jan 1, 1986

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

Mineral sands are being used as the source material for new "high-tech" engineering materials. One such material, Magnesia Partially Stabilized Zirconia (PSZ) has been developed and patented world-wide by CSIRO. Derived from zircon sands, the material is currently produced by Nilcra Ceramics in Australia and is exported world-wide.The properties of the material are contrary to those generally accepted for ceramics and are far more akin to those of steel. The material resists not only abrasive wear, impact and thermal shock, but does so under corrosive conditions that frequently cause early failure of metal and cemented carbide.While the consumption of mineral sands for the production of PSZ is not going to significantly increase the demand in the short term, the material itself may well assist the productivity and processing problems within the industry.

Jan 1, 1986

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By F. H. Muge

The problem of how to handle heterogeneous populations in an ore reserve global estimation arises in many geostatistical studies. In some cases it is possible to split data into different significant types of ore in such way that non-overlapping subpopulations are obtained, and a separate study is possible. In other cases the subpopulations are intermingled and a set of nested structures may model the spatial variability of the ore. Finally, one of the populations, consisting of a small proportion of high grade values of economical meaning, may disturb the structural analysis. In this paper, some methods are proposed to cope with these kind of problems and typical case studies are presented.

Jan 1, 1986

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln's internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers' weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers' weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By Charles U. Keranen

The Tilden Mine is an iron ore mining, processing and pelletizing facility located on the Marquette Iron Range in Michigan's Upper Peninsula. It has a designed capacity to produce 8 million long tons of pellets annually from 21 million long tons of crude. It is a partnership owned by The Cleveland-Cliffs Iron Company, Algoma Steel Corporation, LTV Steel Corporation, the Steel Company of Canada, Wheeling Pitts- burgh Steel Corporation and the Sharon Steel Corporation. Cleveland- Cliffs manages and operates the Tilden. The crude ore averages 35% iron and is primarily non-magnetic iron oxide and silica. The major ore mineral is martite. Hematite, earthy hematite, goethite and magnetite are also present. The principal gangue mineral is chert. The ore grains are mostly in the 10 to 25 micron size range which necessitates very fine grinding for liberation. The concentrating process is the most complex one used in the iron ore industry. The unique technology for Tilden was developed in the mid and late 60's. The design and construction occurred in the early 70's and operation of the first phase which was of 4 MLTPY capacity began in October. 1974. Expansion of the facility to the current 8 MLTPY capacity was completed in 1979. Chemicals are the key to the beneficiation process at the Tilden Mine. The flowsheet utilizes selective flocculation - desliming, cationic silica flotation and concentrate dewatering by thickening and filtering. Nine different process chemcals are used. The control of the reagent feed systems is highly auto- mated. The entire concentrator is operated from a central control room. The concentrator flow diagram is presented in figure 1. The plant consists of 12 primary autogenous grinding lines, a common crushing circuit to handle an intermediate product within the primary grinding section, 24 pebble mill lines with cyclones and deslime thickeners, 12 flotation lines, 4 concentrate thickeners and slurry tanks, 8 lines of filters with six machines per line, and 2 tailings thickeners. A pumping system was installed in 1980 to permit the direct return of tailings thickener overflow water back to the reuse water pumphouse.

Jan 1, 1986

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting and it measures the effectiveness of blasting. Fragmentation is sensitive to not only the interrelationship among the design variables, but also is sensitive to local geology. Local geologic conditions have a significant impact on the success of a blasting operation.

Jan 1, 1986

By W. R. Dearman, N. Turk

The theoretical relations between the strain and stress Mohr circles make it possible to establish a relation between the internal friction angle [ ] and the Poisson's ratio (v) of rocks. The internal friction angle is related to the Poisson's ratio as Sin [-] = (1 - v)/(l + v). This relation gives lower friction angle values than the triaxial Mohr envelopes and higher values than those given by surface sliding friction tests.

Jan 1, 1986

By R. F. Shurtz

This paper uses a simple model to illustrate the fact, widely known to information theorists, that the covariogram represents only half the information in the data used to construct it. It suggests and illustrates methods of putting the other half to use in describing mineral deposits. It also identifies applications in which the phase information is not needed.

Jan 1, 1986

One of the largest and most exciting cast murals in the world has been erected in Johannesburg, forming the focal point of the large atrium in the new headquarters complex for Johannesburg Consolidated Investment Company Limited (JCI). Known as 'Rockface', this is waterwal1 structure formed of cast stainless-steel panels

Jan 1, 1986

By G. Granger, D. Malhotra

The paper briefly reviews the criteria employed in the selection of chemical reagents for testing and discusses the steps involved in laboratory and plant evaluation of these reagents. An example of successful implementation of reagent change in the plant is illustrated.

Jan 1, 1986

By Cole NH

Substantial savings in terms of project time, cost, and financial viability can result through the expert involvement of independent financial advisors in the early stages of any mining project's preparation. This role is not confined to project financing, financial modelling, valuations and corporate finance advice, but may in the early stages be much more strategic in nature, covering a wide group of subject areas. A number of separate examples and case studies are outlined, which show the manner in which financial advisors can be effectively used. The benefits arising from involving an additional professional team with the project group must be offset against the separate and additional cost factors involved.

Jan 1, 1986