Search Documents

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

Introduction Of the techniques reported for cyanide removal from effluents, alkaline chlorination is the most common (Fisher and Wasser, 1969; Reidt, 1969). Shortcomings with this technique are the high reagent costs, chlorine contamination, and potential formation of cyanogen chloride. Chemical oxidation methods are also not suitable to remove cyanide from effluents containing sulphides in suspension, such as flotation tailings. An inexpensive method for removing cyanide, combined cyanide and related species from waste waters has been developed in Inco laboratories. The method is based on the use of sulfur dioxide (or a sulfite), lime, and air as the reagents. The decomposition reactions of cyanide, combined cyanide, and related species are catalyzed by copper in solution. Complete removal of cyanide species, most of which are oxidized to cyanate, is obtained by treating copper containing cyanide effluents with sulfur dioxide-air mistures while maintaining the pH between 6 and 10 with addition of lime. The new approach can also be applied to selective destruction of cyanide and combined cyanide in effluents containing sulphides in suspension, such as pyrrhotite. Again, a sufficient amount of dissolved copper must be present or added. Metals and precious metals present in the effluents are recovered as hydroxides by adjusting the pH of the treated effluents to about 9-10. Using the new method, the anionic species are removed in the following order: Free CN- > Complex CN- > Thiocyanate The above removal sequence is unusual as oxidants such as chlorine and ozone oxidize thiocyanate preferentially over the combined cyanide.

Jan 1, 1985

By L. H. Ketchum, T. L. Theis, W. H. Engelmann

The use of a suspended growth system of Thiobacillus ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor is shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component, followed by limestone neutralization, is both a technically and economically feasible approach to treating these waste waters, compared to existing and other proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this paper, data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 98%. Capital and operating costs are projected to be $80/1000 m3 ($80 per 35, 000 cu ft) of waste water.

Jan 1, 1985

Report M161 Improved recoveries of gold from auriferous calcines and pyrites by fine milling. Report M171 The development of a versatile computer programme for the evaluation of batch flotation results. Report M178 The reduction of chromite in a transferred-arc plasma furnace. Report M179 Optimization of an inductively coupled plasma by the simplex method. Report M182 A techno-economic evaluation of five routes for the comminution of gold ores in South Africa. Report M183 The determination of molybdenum and tungsten in resin by X-ray-fluorescence spectrometry. Report M184 The analysis of silicates, ores, slags, and other materials by X-ray-fluorescence spectrometry. Report M188 Determination of relative sensitivity factors for use in spark-source mass spectrometry.

Jan 1, 1985

By Ross G. Bertinshaw

"The Line Creek Mine of Crows Nest Resources started mining coal in the fall of 1981. There are seven mineable seams with thicknesses ranging from 1.5 to 13 metres and with dips varying from 0 degrees to 60 degrees. This, together with internal partings and the very friable nature of the coal, creates a number of mining problems.The coal is divided into zones depending on the dip of the seam. Each zone requires a different mining technique to ensure optimum recovery and low dilution while still keeping fines to a minimum.Line Creek employs a combination of hydraulic front shovels and backhoes to mine its coal without blasting or use of dozers. This has been very successful in reducing the proportion of fine coal hauled to the plant, thus improving quality control and reducing costs in coal processing.There have been a number of other benefits from the use of excavators instead of more conventional methods. These include better selectivity, good cleanup, reduction in traffic at the face and lower cost.IntroductionThe Line Creek Mine is situated approximately 25 km north of Sparwood in southeastern British Columbia (Fig. I). Preproduction stripping began in J98J with the first coal shipments made in 1982. In 1983 the mine produced 2.1 million tonnes of raw coal.Similar to other East Kootenay coals, the seams at Line Creek are characterized by their friability, producing a large proportion of fine coal during mining. In an attempt to reduce these fines Crows Nest Resources has instituted the use of hydraulic excavators to mine and load the coal.Hydraulic excavators offer other substantial advantages over front-end loaders and dozers, which has been the conventional system in other mines in the area."

Jan 1, 1985

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Travis Q. Lyday

During 1983, Ecuador's gross domestic product (GDP) decreased by a reported 3.3% in real terms, the second consecutive decline in the economy after more than a decade of growth generated mainly by petroleum export revenues. The slowdown was due, in part, to the effects of the world recession, lower foreign demand for oil, depressed world oil prices, and reduced demand and prices for Ecuador's traditional agricultural exports. Inflation accelerated to an estimated 55% annual rate. The sucre was devalued in March, for the second time in less than a 12-month period, by 27% after remaining unchanged during the previous decade. In addition, continuous adjustments were made every weekday, effectively devaluing the sucre another 30% by yearend. Ecuador's production of crude petroleum increased almost 12% in 1983 compared with that of 1982. Average daily production was 237,100 barrels per day (bbl/d), up from 211,300 bbl/d in 1982.

Jan 1, 1985

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

By Kai Nielsen

A model has been developed for sensitivity analysis of open pit bench blasting. The model simulates the cost effectiveness of various blasting designs in relation to the equipment used for drilling, loading, hauling and primary crushing. The simulations will give an indication of the optimum powder factor giving the lowest over-all costs for drilling, blasting, handling and crushing.

Jan 1, 1985

By W. D. Presley, T. R. Harrell

This paper will be a case history of the shaft and tunnel concrete lining techniques used at the Rocky Mountain Pumped Storage Project located in northwest Georgia. Emphasis will be placed on the shaft lining techniques with only a brief description of the tunnel concrete lining techniques. The 10.67 meter (35 foot) diameter shaft and tunnel concrete linings are 0.61 meter (2 foot) nominal thickness with a single row of reinforcing bars. The tunnel was placed in 18.29 meter (60 foot) lengths with bulkheaded end sections. The 172.72 meter (566.68 foot) vertical shaft was placed in 3.05 meter (10 foot) high sections using jump forming techniques.

Jan 1, 1985

By Coopers &. Lybrand

INTRODUCTION From a tax viewpoint, United States mining companies are at a substantial disadvantage in the international mining area compared with companies in other major capital-exporting countries, according to a 1975 study by Coopers & Lybrand for the American Mining Congress. The study compared the relative tax position of a United States investor with investors from Belgium, Canada, France, Germany, Japan, the Netherlands, Switzerland, and the United Kingdom. The comparison was based on average rates of return realizable by investor companies on four mine-model investments in twelve capital-importing countries. The countries in which these investments were assumed to be made are varied in their tax systems so that a wide range of possibilities was included in the analyses. Each mine model was standard so that the rates of return for each investment by each investor were affected solely by the respective tax systems of the capital-exporting and capital-importing countries. UNITED STATES POSITION The study found that the United States competitive position, in terms of the average rate of return on an overall basis, ranked next to last among the nine capital-exporting countries in the study. Further, the United States overall rate of return is more than 20% below that of the country (Japan) with the highest overall rate of return. On an average return-on-equity basis, the United States' position among the nine investor countries, for each of the mine investments studied, was: copper, eighth; iron ore, sixth; nickel, fifth; manganese, a tie for last place. Figure 1 shows the overall results realized by each capital-exporting country on the basis of average return on equity. [ ] The frequency with which a given capital-exporting country attains the highest or next highest rate of return in a capital-importing country provides further insight and another basis for comparing the tax laws of the capital-exporting countries. Of the situations compared in the study, the United States never attained the highest rate of return, and reached the second and third highest rate of return in only two instances. The tables showing the frequencies of rankings are given in Table 1 for each of the four mine models. In summary, the United States mining company does not have a competitive advantage under the tax rules when competing for mineral concessions in other countries. The United States company, in fact, appears to be at a clear disadvantage. The study also considered the effect of the following recent tax proposals on United States investors in international mining ventures:

Jan 1, 1985

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

By John P. Coughlin

The Bureau of fines has tested a portable microseismic processor recorder at the Galena Mine, Wallace, ID, both in an environmentally controlled enclosure and, with minimal protection, in a working area of the mine. In both trials the device demonstrated effective and reliable data acquisition capabilities.

Jan 1, 1985

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

By G. E. Karantzavelos

A novel two-stage froth flotation process for the recovery of pure magnesite from low grade ores is described. The process consists of a first-stage, magnesite flotation step where a rougher magnesite concentrate is floated with amine collectors. The first-stage froth concentrate is then repulped in fresh water, and quartenary ammonium salt and fuel oil are added to float the remaining impurities. The results from laboratory batch tests show that a high-grade magnesite concentrate assaying 0.99-0.20% Si02 and 2.84-0.46%a Ca0 can be produced. Regulation of the variables controlling magnesite froth flotation also allows the variation of the ratio % Ca0: % SiO2, between the acceptable limits 0.32 to 5.79. This ratio is important to the quality of dead-burned magnesite.

Jan 1, 1985

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By Madan M. Singh

Increasingly, geotechnical data are being collected for various types of coal development projects. In many cases, a specific design concern is addressed. However, many data collection programs are not intended to immediately support mine design activities or to resolve a specific concern. The following discussion describes some current geotechnical approaches in mine planning, development of reserves, and peripheral activities. Types of Data Collection Programs Geotechnical data collection is increasingly becoming a part of standard coal exploration programs, performed along with stratigraphic evaluations and coal quality tests. The aims of such programs vary. The purpose of the exploration may be to fill out the portfolio on a block of reserves that is to be sold, leased, or held for potential future development. In such a case, a generic suite of geotechnical data are collected. The resulting engineering reports may touch on the more well known mining problems of the area, but detail may be lacking. The geotechnical data are mostly intended to enhance the saleability of the package. Mine design alternatives are generally not addressed.

Jan 1, 1985

Contents

Jan 1, 1985

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By John R. Bartels

In laboratory testing, the Bureau of Mines established criteria by which common resin-grouted roof bolting systems can be evaluated and compared. Ultimate strength and stiffness were determined for nonten-sioned full-column, point-anchor, tensioned full-column, and debondable resin-grouted bolts, and for variations on full-column boltsn Bolt per-formances were compared using the performance of the 3/4-in full-column resin-grouted bolt as the standard. New and innovative systems can also be qualitatively compared against this standard. Since the medium into which a resin-grouted bolt is installed is one of the most important parameters affecting bolt performance, various host mediums were used in the testing: sandstone, concrete, simulated coal, simulated shale, and plaster. Bolt performances expected in other mediums can be inferred from the response patterns obtained in these mediums. Results indicate several functional differences among bolt types. Where resistance to shear is important, point-anchor bolts may outperform nontensioned full-column bolts at a lower cost. In medium-to soft-strength rock, tensioned full-column bolts perform best. Also, varying the resin-steel ratio seems to have little effect on the properties of a full-column bolt, when proper resin mixing is ensured.

Jan 1, 1985