Search Documents

By Jean-Michel Rendu

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual fitting of the model is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. A number of interactive methods are described, which are adapted to the modeling of semivariograms in one-, two-, or three-dimensional environments.

Jan 1, 1982

Provide better ventilation for mines by reducing air leakage around stoppings. Approach Most stoppings are constructed of concrete blocks and trowelled-on mortar and are not very airtight. Bureau of Mines research has shown that brushing on modified mortar containing fiberglass and/or other additives, that enhance strength and adhesion, minimizes air leakage around and through the stoppings. Airtightness is an important factor in building stoppings since an airtight stopping will provide for more efficient ventilation airflow and more cost-efficient use of the mine's ventilation system. How the New Technique Works After broken floor and rib material is removed, the stop-ping faces are covered with one or two coats of modified

Jan 1, 1982

The paper describes the development leading to the bucket wheel excavator systems now used in the Latrobe Valley and refers in particular to the new S.E.C.V. dredgers Nos. 14 and 15 which will be employed in the Loy Yang open cut. The design concept and operating possibilities of these dredgers are described in detail with reference to the machine characteristics designed for the operating conditions in the Latrobe Valley. The design is compared with units of similar capacity in open cuts of other countries.

Jan 1, 1982

By Vassiliki G. Stavropoulou

Although plane-strain is the preferred method of analysing many rock mecahnics problems, little is known about the behaviour of rock under this loading condition. A simple and inexpensive apparatus has been built for laboratory testing of rocks in plane-strain conditions. A thorough .investigation of the specimen geometry and the friction end effects showed that the results can be considered as reliable. The behaviour of a brittle sandstone in the simplest plane-strain condition [(03 = 0)] is significantly different than that of the uniaxial compression [(02 = U3 = 0)]. The plane-strain values of the Young's Modulus and the Poisson's Ratio are decreased in comparison to the corresponding uniaxial values. Dilatancy is also reduced in plane-strain, whereas the pre-failure brittleness of the rock increases. The most dramatic effect of the plane-strain condition is that on the strength of the sandstone, which increases by 49 per cent in comparison to its uniaxial compression value.

Jan 1, 1982

By William A. Rhoades

INTRODUCTION Ever since miners were faced with the task of moving ore, some form of scraper has been in use. At first, men and beasts of burden supplied the power to move the scraper, and later, machines were developed for this purpose. In the early 1900s, a few mining properties used small pneumatic single-drum winches to pull loaded scrapers to a raise or ore pocket, and the empty scraper then was dragged back to the muck pile by a miner, as shown in Fig. 1. Just prior to 1920, an improvement was introduced, using two single-drum hoists. As illustrated by Fig. 2, the second hoist was used to return the empty scraper to the muck pile. However, this arrangement still re¬quired two men, one operating each hoist. The next developmental step was to eliminate the second man by locating the hoists side-by-side and using one man to control both hoists. As illustrated by Fig. 3, this involved the use of a tail rope over a sheave to pull the scraper back. The greatest progress in development and the great¬est increase in the use of slusher haulers occurred between 1920 and 1930. In 1921, the Sullivan Machinery Co. designed and built the first two-drum scraper oper¬ating on the principle illustrated by Fig. 4. It was powered by a 4.5-kW (6-hp) Turbinair(r) motor and would pull a 450-kg (1000-1b) load at 0.61 m/s (120 fpm). In 1922, this unit was shipped to the Verona Mining Co. of Caspian, MI, and it experienced immediate success in the Lake Superior iron ore district. Since the two-drum slusher was much less expensive and more efficient than hand mucking, the Lake Superior mines were saved from financial disaster when iron-ore prices fell 25% between 1923 and 1925. Immediately there¬after, a demand developed for slushers that would oper¬ate with electric power, which was considerably cheaper than compressed-air power. In 1923, the Sullivan Machinery Co. responded with the first electric-powered double-drum hoist. During subsequent years, design improvements in¬cluded separate tail-drum gearing to increase the tail¬drum speed, as welt as a number of safety features such as rope guides. One result of these improvements and their utilization by the Michigan iron mines was an in¬crease of 100% in the tons of ore per miner per day in those mines between 1924 and 1929. Since the two-drum slusher was capable only of straight-line mucking, it was not a practical machine for use in open stopes. In 1929, the Sullivan Machinery Co. introduced the first three-drum slusher. As illustrated by Fig. 5, two tail drums and one hauling drum were provided. A tail sheave could be placed at each side of the stope, and the ore then could be loaded and hauled to a central point from the entire width of the stope. During the 1930s, progressively larger slushers were demanded. By 1940, two- and three-drum units were available with motor power as high as 45 kW (60 hp), and slusher power continued to increase after 1940. Be¬tween 1951 and 1952, Joy Manufacturing Co. designed a 112-kW (150-hp) two-drum Blusher for the Climax Molydenum Co. Although there has been no demand for a slusher more powerful than this, 150- to 225-kW (200- to 300-hp) slushers are quite feasible at the pres¬ent time. During the last 30 years, many slusher improvements have been made to the operating life, operational safety, and ease of operation and maintenance. Increased tail-drum speeds have decreased overall scraping times. Rope guards, totally enclosed drums, and operator shields have reduced the hazards of injury due to wire¬rope breakage. Improvements in lubrication have made the slushers relatively maintenance-free, with long operating lives. The introduction of spring-actuated drag brakes prevented uncontrolled unreeling of dis¬engaged drums, allowing the development of practical remote-control slusher operation. Remote control now is available in a choice of all-air, all-electric, or air¬electric slushers. APPLICATIONS Quite simply, slushers are used to load and transport material (ore), generally over a short distance of from

Jan 1, 1982

By B. Hornsby

At the Mount Isa mine, Mount Isa, Qld., Australia, sublevel open-stope mining is used for copper ore while both sublevel open-stope and cut-and-fill methods are used for the silver-lead-zinc ores. Production in 1979¬80 was 4 730 000 t (5,200,000 st) copper ore and 2 590 000 t (2,850,000 st) of lead ore. The deepest mine level currently is 960 m below the surface. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The mine is located in the valley of the Leichhardt River in Lower Proterozoic sediments of the Mount Isa group. The regional strike of the sediments is north¬south and they have a persistent westerly dip of about 1.1 rad (65°). In the mine area, the Mount Isa group comprises a sequence of alternating bands of dolomitic shales and siltstones some 3.2 km (2 miles) in width. It is bounded on the east by greenstones and quartzose sediments of the Eastern Creek volcanics, and on the west by the Mount Isa fault, west of which occur schists and other metamorphic rocks. The ore bodies as currently known at Mount Isa are restricted to the Urquhart shale, a formation of thinly bedded pyritic, dolomitic, and volcanic shales some 1070 m (3500 ft) thick. Towards the top of the Mount Isa group sediments, copper and silver-lead-zinc ore bod¬ies occur as contiguous but discrete entities and are mined and treated separately (see Figs. I and 2). Argentiferous galena, sphalerite, pyrite, and minor associated sulfides occur in distinct concordant bands throughout the Urquhart shales. Wherever these bands are grouped together in sufficient density they constitute silver-lead-zinc ore bodies with widths varying up to 36.6 m (120 ft). Other mineralized bands are common in intervening beds. Individual ore bodies persist for many hundreds of meters concordant with the strike and dip of the enclosing shales. Intersections of these beds with fold axes provide local zones of enrichment but otherwise the mineral content of the ore bodies varies only slightly throughout the extent of the dip and strike. Chalcopyrite is the only important primary copper mineral. It occurs in association with pyrite and pyrrhotite as disseminated flocks and as vein fillings throughout irregularly shaped zones of folded, brecciated, and re¬crystallized Urquhart shale. These zones, which are lo¬cally termed "silica-dolomite" bodies, are broadly transgressive to the shale bedding and confine all significant copper mineralization to the virtual exclusion of silver¬lead-zinc mineralization. In some areas, the downward percolation of acidic water through faults and shears has caused extensive leaching of the coarse-grained carbon¬ates to depths in excess of 610 m (2000 ft), but most of the silica-dolomite remains unleached and the ground is competent. The majority of lead ore being mined is north of the main shaft pillar (R62, U62) area. The major lead¬producing areas for many years have been the Black Star ore bodies (2 and 5 ore bodies) and the Racecourse ore

Jan 1, 1982

By W. W. Mason

The US began exporting coal in the late 1800s, at first in very small quantities to Canada and, beginning in 1897 and 1898, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War I when shipments overseas increased from 7.3 Mt/a to 20 Mt/a. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War II when the US again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the US was the only country able to supply large quantities of coal at reasonable prices needed for reconstruction of the European economy, the US coal exports overseas expanded rapidly to 38.6 Mt in 1947. Additionally, we shipped 23.8 Mt of coal to Canada in that year for a total export of 62.3 Mt. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 69.3 Mt - a high that has not been reached since. Over the years the level of US coal exports has fluctuated fairly widely. Approximately 80-90% of all US coal exports are high quality metallurgical grade coal so our exports level depends directly on world-wide economic conditions and world steel production levels.

Jan 1, 1982

By Bertrand Wolfman, William E. Stanley

"This paper reviews the traditional mine accounting systems, including ""custodial accounting"" and unit costing, and then suggests that the use of flexible budgets represents a more suitable method of reporting costs in order to assist the mine manager in improving productivity. Examples of various applications are given to show that the result is a clear reporting structure.Custodial Accounting is Emphasized in Traditional SystemsTraditional mine accounting has been mainly concerned with the accuracy of financial reporting to ""head office"" for the use of the directors and the company's bankers and shareholders. This is often called custodial accounting and it represented the main purpose of accounting when first developed in Europe hundreds of years ago. This important development permitted the establishment of enterprises which were separated from their owners because they could rely on accurate financial reports of management's stewardship.As custodial accounting is fairly broad and historical in nature, it is often not very useful to the mine manager for ongoing monitoring of performance of mining, milling, maintenance, and other support and staff groups. In spite of the considerable investment in accounting staff and computer support, many accounting systems have not been upgraded so that they accurately reflect workplace performance on a weekly or monthly basis.Budgets are Often FixedMany mines today also still emphasize fixed budgets. Thus, the mine plan which is set in the fall of one year is converted to a monthly tonnage and detailed dollar budget for periods of up to sixteen months in the future. The only certainty in this plan is that actual events will differ; timing, mix of mining methods and production volumes will differ on a monthly basis.Unfortunately, the fixed budget has no capability to reflect these operational changes. It is frozen for the full year. The result is that actual results will inevitably be compared to an outdated target."

Jan 1, 1982

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By Malcolm J. Robinson

Over 80% of Australia's population lives within 200 km of the coast, 70% in 10 major coastal cities. Potential cement raw materials are widely distributed but deposit size, quality, transport, market and environmental considerations are important in determining economic value. Major production locations are in a variety of geological environments ranging from Lower Paleozoic crystalline limestones to Tertiary and Recent polyzoal limestones and limesands, both onshore and offshore. Raw material transportation is by road, rail, sea, aerial ropeway and pipeline; road/rail transportation of the finished product is traditional but movement by sea of clinker and cement is increasingly a feature of the industry.

Jan 1, 1982

By J. R. Dolegowski, W. S. Jensen, S. M. Olafson, W. H. Champion, G. A. Kordosky

The use of pH control in solvent extraction circuits to aid in metal separation, concentration, and purification is an extremely useful technique applicable to a wide range of solutions. This paper discusses the technique in general and then gives examples of its use in extraction stages, wash and/or scrub stages, and in stripping stages, to effect the desired metal separation, concentration, and purification. Specific examples cited include Cu-Ni, Cu-Zn, and U-Mo separations using commercially available liquid ion exchange reagents.

Jan 1, 1982

By Bruce C. Trent

The need for effectively evaluating the potential for surface subsidence due to under- ground mining has been widely documented. As the emphasis within the coal mining industry changes to reflect the increasing demand of this resource, the potential for damage due to differential surface subsidence will certainly become more acute. The present state-of-the-art of predicting ground motion due to underground excavations is, at best, primitive when one considers the immense complexity of possible geological inter- actions. For the most part predictions have been limited to empirical evaluations based upon earlier case histories. While the tools of the subsidence engineer are limited, they are important and serve to provide reasonable bounds for possible ground motion. As underground mining becomes more extensive, however, there will be many instances where excessive subsidence will be most undesirable and yet there may be few, if any, case histories similar to the operation in question.

Jan 1, 1982

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

Jan 1, 1982

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By William J. Taylor

Strictly defined, a stull is an inclined or horizontal timber support; a vertically placed timber is defined as a prop. Common usage allows the catchall term "stull" to refer to all such uniaxial mine support, regardless of orientation. Typically a stull is a round wooden column that is wedged in place to provide short-term auxiliary support between sill and back, or between hanging wall and footwall. Stulls may be used exclusively or in con- junction with other support systems such as roof bolts, shotcrete, or cribbing. Stulls are used both as local temporary support in stoping operations and for uniform systematic support installations. Where stoping areas are to be abandoned soon after excavation, stulls may be used to provide temporary support during mining operations. Where controlled caving and subsidence is required, stull supports are designed to fail in a systematic, predictable manner. Wood type is selected on the basis of availability, price, and load carrying characteristics. Coniferous woods are typically used, especially to carry heavy ground loads. Brittle woods are generally avoided because of their tendency to fail suddenly. Gradual yielding failure is preferable to sudden, unexpected failure of the support. Some usage of wood from deciduous trees such as cottonwood and other poplars has been reported in Grants, NM. These stulls reportedly mushroomed as the ground load increased but continued to maintain their structural integrity. Stulls fabricated from structural steel are used in special applications. Adjustable lengths are commercially available in mechanical, hydraulic, and pneumatic designs. The high cost of mechanical stulls limits their use to mining systems where recovery and reuse is possible. End blocking, also called headboards or footboards, uses wood blocks that are placed between the stull end and the ground they are supporting. The blocks are typically 50.8 to 101.6 mm (2 to 4 in.) thick, 203.2 to 304.8 mm (8 to 12 in.) wide, and 381 to 609.6 mm (15 to 24 in.) long. End blocking serves to distribute the support over wider back area. Compression of the end blocking gives visual indication of wall movement prior to failure of the stull. A common application of the stull is in flat-bedded uranium mining during pillar extraction. Many western US uranium mines use a pillar pattern development to delineate the irregular ore pods. After development of an appropriate sized pillar, the ore pillars are then sequentially mined out, leaving the undercut hanging wall or back to cave. Where thickness of the ore is less than 4.3 m (14 ft), stulls are generally used to provide ground control as the pillar is removed in slices. Experience dictates the density of stull placement. In general, the number and size of stulls should be sufficient to resist ground closure and to provide support for drilling and loading operations adjacent to the pillar. Stulls next to the mining face are often lagged 0.9 to 1.2 m (3 or 4 ft) up from the floor (or sill) to confine the blasted ore to a passage next to the pillar. Mucking is simplified by this confinement. Experience dictates whether back control along a mining face requires removal of stulls to allow con- trolled subsidence of the back or hanging wall. Without caving or closure, abutment pressure can create poor ground conditions near the pillar.

Jan 1, 1982

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982