Search Documents

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

The New Southern Railway (NSR) involves the excavation of approximately 10 km of single bore tunnel from Tempe Reserve, Tempe, to Prince Alfred Park (PAP). PAP is located just south of Central Railway Station in SydneyÆs Central Business District (CBD). From Tempe Reserve the alignment takes the tunnel under Sydney Airport including the main north/south runway. Sydney Airport is approximately 8 km south of the CBD. The NSR is being constructed by a private group, the Transfield Bouygues Joint Venture (TBJV). Transfield is a major Australian contractor and the French contractor, Bouygues, is providing the soft ground tunnel construction expertise and is also responsible for the design of the concrete segmental lining. This paper sets out to present in some detail the issues involved in tunnelling under the airport and in particular under the north apron, the main north/south runway and the new elevated roadway. The paper concentrates on these three areas on the airport with an emphasis on the following. The risks involved and measures taken to minimise the risks in tunnelling under the International Terminal north apron (with Jumbo Jets parked immediately above). Secondly, settlement predictions, settlement and runway operation criteria and the actual settlements that have occurred on the main north/south runway. Finally, the criteria that was developed during the construction of the deep bored piers for the elevated roadway at the Domestic Terminal as the TBM passed through this area of construction activity.

Jan 1, 1999

By Julio E. Claudeville

Approaches and Lessons Learned ??Address business needs?local skills training and employment ?local procurement programs ?health and safety programs ??Ensure consultants/ advisors/ contractors apply Company standards ?especially in the field/ locally ?will not be differentiated from the Company itself

May 1, 2006

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By Byron B. Boatright

The energy which causes oil and gas to flow from a reservoir formation into a well depends upon a differential between the formation pressure and the pressure at the well face. This differential pressure may be the result of any one of at least three forces, or a combination of them. Gas under pressure in an oil-producing formation (part of the gas may be in solution and part in contact with the oil) is the principal source of energy for producing oil in most fields. In some fields, however, hydrostatic pressure due to water in contact with the oil and/or the force of gravity may be important factors in causing oil to flow into a well. Still another force affecting oil movement is suggested by some students of the problem; the force dependent upon the phenomenon of capillarity. Hydrostatic pressure is seldom the only source of energy in an oil sand, but it is commonly an adjunct to the compressed gas in the formation. Where this condition prevails, increased production may be obtained provided the water encroachment is properly controlled. In addition to the water-drive effect, the hydrostatic head may tend to maintain pressure in the formation by progressively reducing the volume of the reservoir as withdrawals to the surface are made through the producing wells. The action of the force of gravity on the oil in a formation is of relatively small importance, from an energy standpoint, until the last stage of the productive life of a well is reached. This force is the only remaining natural source of energy in some of the eastern fields, but in most of the deep wells of the Mid-Continent and California districts the force of gravity can be precluded as a source of energy, because the wells reach their economic limit of production before the force of gravity becomes an important factor in moving oil to the wells. Since the majority of fields produce oil chiefly by reason of the gas pressure in the oil horizons, the following treatment deals mainly with factors that influence gas-energy relationships. Gas-energy Relationships Formation Pressures The gas pressures existing in oil-producing formations may be the result of a combination of several contributing factors. All fluids under

Jan 1, 1932

By H Bruyn, K Ehrig, V Liebezeit, A Robertson, M Smith, D Grant

"The Olympic Dam geometallurgy program has generated a large quantity of data that has been used to create a geometallurgically enabled block model. An ongoing challenge is to convert data into usable information and embed geometallurgical practices into resource model development and mine planning to assist with the identification of opportunities to maximise value.This paper will discuss the methods used to disseminate geometallurgical information throughout the planning life cycle including data extraction methods from the geometallurgy acQuire database, and the inclusion of a geometallurgy module in the Olympic Dam Stope Reserves database. The use of geometallurgical information in short-, medium- and long-term mine design and scheduling, including its use in grade descriptor development and stope value assessment tools will also be presented. The detail of development of specific geometallurgical models is outside the scope of this paper.At Olympic Dam, the incorporation of geometallurgical capability within the long-term planning team, traditionally the domain of mining engineers, has proved essential in broadening the base of geometallurgical knowledge as well as focusing geometallurgy resources on value-adding areas while providing a holistic risk based long-term plan.CITATION:Liebezeit, V, Ehrig, K, Robertson, A, Grant, D, Smith, M and Bruyn, H, 2016. Embedding Geometallurgy into Mine Planning Practices – Practical Examples at Olympic Dam, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By S. M. Bishoff

The disturbance of surface land to support the underground mining of coal requires several hundred acres to produce easily in excess of $1 billion in sales at a moderately sized mine over 20-30 years. Due to the recent influx of environmental legislation, these surface operations must now undergo complete reclamation upon permanent cessation of production. This reclamation procedure has become so complex that the cost of reclamation must be a major consideration in the design of a new mine. This presentation will discuss these costs as they may be methodically evaluated and surcharged as a percentage of the product price. When placed in the proper, logical perspective, it is anticipated that the obstacles involved in this process may be minimized.

Jan 1, 1985

By Fabjanczyk M. W

A limitation to present theoretical roof reinforcement design methods is the inability to derive accurate and quantitative information about the roof rock condition and the action of reinforcement at various excavation stages. To obtain the information required to assess roof rock stability, detailed monitoring of the in-situ behaviour of reinforcement and roof strata is required. Reliable instru- mentation and techniques have been developed for use in underground coal mines to identify the geometry and magnitude of displacements occurring in roof rock and the forces generated in reinforcement. The use of such instrumentation allows an accurate assessment of the in-situ capability of reinforcement and the mode of reinforcing action developed. In-situ monitoring can supply data required for the practical design of reinforce- ment and assess the potential stability of current designs. The use of such data together with mine wide appraisal of rock and stressfield considerations, can allow roof reinforcement to be designed on the basis of a predicted roof Response.

Jan 1, 1986

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By Claus G. Goetzel

PRESSING of powdered metal parts is best done in the direction of the shortest extension of the piece, to avoid too great a loss of pressing force through internal [ ] friction. As long as curved surfaces, recesses, or offsets occur only parallel to this shortest axis of pressure, no special difficulties arise: the cross sections, perpendicular to the pressure, do not vary, nor does the shape of the parts change during compression except for a gradually reduced thickness (Fig. IA). The problem becomes more difficult, however, when the curved surfaces or recesses are perpendicular to the shortest axis of the part (Fig. IB). Two processes for molding uniformly dense parts with complicated shapes from powdered metals are described in detail in this paper. Both can be employed successfully by those trained in the art. The first refers to curved parts; the second is especially adapted to parts having one or more recesses or steps. Both methods, as set forth here, are applied under the condition that presents the more difficult problem. For clarity, before description of the two practical methods, the variable factors in molding powdered metal parts will be reviewed, then an idealized procedure will be considered briefly. VARIABLE FACTORS IN MOLDING POWDERED METAL PARTS Compression Ratio Compression ratio is defined as the proportion of the final relative density of the compact to the apparent density of the powder. For iron powder of an apparent density of 3.0, for example, a compression ratio of 2 1/2 : I would be required to produce a compressed compact of 7.5 density; whereas for another iron powder having an apparent density of only I.5, a compression ratio of 5:I would be required to produce the same density. The lower the powder's apparent density, the greater must be the compression ratio for pressing compacts of high density.

Jan 1, 1945

By Edward Sampson

Despite the many industrial uses, the world market for silver as a commodity is far from free, being dominated by the U.S. Government both through acts of Congress and by policy of the Treasury Department. This discussion will consider aspects of supply, demand, and price with a view to the future. Changes in Sources of Supply: The world's peak production of silver, 278 million oz, was in 1937. In the 1850's world production was about 30 million oz, having risen from a yearly average of 11 million oz for the first half of the century. From 1860 to 1940 there was a steady rise, broken only by World War I and the depression of the early 1930's.

Jan 7, 1960

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By M. Holm

Coal is an important fuel for energy generation, and since there are no adequate alternatives it will also be for the next decades. The deep lying hard coal is important in particular because of its high energy content. Automation of underground mining has led to major improvements in productivity and safety. A fully mechanized longwall shearer workface has already reached a high degree of automation and provides a high productivity for example utilizing the memory cut. Current researches and developments in longwall mining are focused on extending this method by adaptive cutting drum height adjustment. The so-called horizon control is often based on memory cut methods. Horizon control in this way requires information of the environment, which can be provided by models (seam model, cut model) and coal interface detection (CID). Available CID systems only provide an optimal output under specific conditions. The authors propose the shield-data-based horizon control (SDHC) system as an alternative approach. SDHC does not require information from a CID system or an environmental model. All necessary information is provided by roof supports, shearer and process monitoring. The SDHC system was tested in simulation under different seam conditions and yielded promising results which will be presented in this paper. In cooperation with the German mining company RAG the SDHC has already reached an experimental stage. A test assembly was built up at the surface and the SDHC system was implemented on real mining equipment. To make the test scenario as realistic as possible, the SDHC system was only connected to the monitoring system, not to the simulation model. The aim of these tests was to establish the cooperation between all subsystems, find appropriate controller parameters, locate and address safety critical aspects and finally to achieve an automatic cutting drum height adjustment. An introduction of SDHC for shearer guidance is given in this paper. The experimental tests are described and the control results of the realized SDHC system on the test assembly are shown.

Aug 1, 2013

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993

By W. A. McKinney

Bureau of Mines Research has demonstrated that it is technically feasible to segregate oxidized copper ores by use of a direct-fired, refractory-lined rotary kiln. Previously, the segregation process had been effected only in much more complicated indirect-fired, stainless steel kilns, The method comprises heating crushed ore premixed with small quantities of salt and carbonaceous material, such as coke, to about 830° C to produce copper as fine flake and metallic films on the surface of the coke particles. After grinding of the cooled furnace calcines, the copper is recovered by conventional flotation. During direct-fired segregation it was necessary to closely control the air-gas mixture in the burner. Good copper recoveries were obtained only when adding air in the limited range of 1.15 to 1.2 times the theoretical amount required for combustion of the natural gas. Batch trials of the new technique on quartzite-, limestone-, sandstone-, and limonite-type oxidized copper ores containing from 1.4 to 6.2 percent copper yielded flotation concentrates containing from 3.7 to 45 percent copper, representing 84 to 95 percent recoveries. Analyses of the furnace gases showed that loss of copper by volatilization was negligible. The preliminary direct-firing segregation studies were complemented by continuous runs on the quartzite ore, containing 1.4 percent copper, in an integrated segregation-flotation pilot plant having a 60 pound-per-hour capacity. In a typical test, 84 percent of the copper was recovered in a cleaner flotation product containing 25 percent copper. The study will be continued to further delineate the conditions for good segregation as effective use of standard ceramic-lined kilns will render the process more attractive from a commercial standpoint.

Jan 1, 1963

By D. R. Parrish, K. W. Beaver, H. W. Wood, R. W. Rausch

A pilot test of forward combustion in the Shannon pool, Salt Creek field, Wyo., is described. The Shannon sand, 950-ft deep, contains a heavy (25" API), viscous (76 cp) oil. Natural reservoir energy is limited. Primary production, intermittent since 1889, recovered only about 2 per cent of the oil in place. The field is operated by Pan American Petroleum Corp. for the Midwest Oil Corp., the owner. The original pilot was a 1.32-acre five-spot. The expanded pilot has eight producing wells surrounding a roughly triangular area of about five acres with the injection well near the center. A control or comparison well was also recompleted in another part of the field. Operation of the pilot has been little different front an ordinary gas drive. Little special equipment was found to be absolutely necessary. Except for some use of a temperature-resistant cement, all wells were conventionally completed. In spite of poor oxygen consumption, the over-all performance of the pilot has been good. Total oil recovery to June 1, 1961, was 73,971 bbl. The wells of the original pilot alone had produced about 24,000 bbl, equivalent to 50 per cent of the oil in place, when fire breakthrough at the first well occurred. These wells have now produced oil equivalent to more than 74 per cent of the oil in place in the original pilot area and production is continuing. It appears that ultimate recovery will approach theoretical maximums before the wells must be abandoned. Performance of the pilot has been encouraging, and expansion to a fieldwide combustion operation is being investigated. INTRODUCTION The results of both laboratory investigations and field tests of underground combustion have been reported previously.' However, most of the field tests were primarily experimental. More information and experience are needed before forward-combustion operations can be engineered with confidence. The purpose of this paper is to present the results of a successful pilot test of forward combustion. These re- sults should increase confidence in forward combustion as a practical method for commercial oil recovery. HISTORY OF THE SHANNON POOL The Shannon pool is located on the north end of the Salt Creek field in Natrona County, Wyo. It is approximately 50-miles north of the city of Casper. The Shannon pool's3 discovery well was completed in 1889, making this one of the oldest oil fields in the Rocky Mountain region. Three more wells were drilled in 1890. First production was hauled in wooden barrels by horse and wagon to the railroad in Casper. In 1894 a small refinery, the first in Wyoming, was built in Casper to process the Shannon crude. In the following years the field changed hands several times. It appears that each new owner did some development drilling as several wells were completed in each of the years 1895, 1902, 1905 and 1912, with negligible development in the intervening years. Forty-eight wells were drilled in this period, but many were later abandoned. Discovery of the more prolific Salt Creek field proper ultimately forced suspension of operations at the Shannon pool. After 1915 there was only sporadic production, mostly to supply cheap boiler fuel to drilling rigs in the Salt Creek field. But even this was discontinued in 1931. Since then the pool had been dormant until the recent operations, which are the subject of this paper. The Shannon pool is now owned by the Midwest Oil Corp. Field operations are conducted for Midwest by Pan American Petroleum Corp. THE RESERVOIR Fig. 1 is a map showing subsurface contours of the Shannon pool. The reservoir is on a nose of the Salt Creek anticline dipping to the north at about 500 ft/mile. The trap is provided by a shallow fault on the updip side of the productive area. The downdip limits are bounded by water, but this water has not provided an effective source of reservoir energy. The Shannon sand outcrops at many places in the immediate vicinity, providing good surface indications of the Salt Creek anticline. At the Shannon pool the sand has been lowered by faulting and is overlain by about 900 ft of shale and other sands. The Shannon sand consists of two members. The upper, a water sand, is about 40-ft thick and is separated from the lower member by several feet of sandy shale. The oil pay occurs in the lower mem-

By A. A. Sizikov, V. A. Sizikova

Key parameters to consider for any producer: bring down production cost and lead time; Lean production as a tool to achieve maximum efficiency; How to implement lean principles: discontinuous vs. continuous production (aluminum industry); About RUSAL: global top-three aluminum producer; Lean tools at use at RUSAL's production facilities; Pull system, Standardization of work, Just in time, Continuous improvement, Customer-Supplier relations, etc.

Jan 1, 2006