Search Documents

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By R. E. Collins, Paul B. Crawford

Potentiometric model studies have been made of ertically fractured reservoirs. All fractures originated at he well and extended into the reservoir for various distances. Studies were made to determine the areal sweep efficiencies for line-drive patterns. The areal sweep efficiency for the unfractured system studied war 70.6 per cent. It was found that if the vertical fracture war paralIel with the direction of flood, the areal sweep efficiency may be considerably reduced, approaching zero in some instances. If the fracture was at right angles to the direction of flood, the areal sweep efficiency may be greater than that for the unfractured system. The sweep efficiency depends on the length and orientation of the fracture and direction of the flood. It is concluded that considerable effort should be made to determine the nature and direction of fractures before initiating a flooding program. Such information is required if the maximum sweep efficiency is to be obtained and channeling is to be reduced to a minimum. INTRODUCTION The recent development and application of fracturing techniques to petroleum reservoirs has served to focus considerable attention on the effect such fractures may have on secondary oil recoveries. The opinion has been expressed that fracturing may not alter appreciably the water flooding possibilities. Others have thought that channeling may occur and that the creation of fractures may serve to substantially reduce the possibilities of conducting a successful water flood in the reservoir The purpose of this study was to obtain quantitative estimates of the effect of vertical fractures on the areal sweep efficiencies of line-drive flooding patterns. In presenting this work on vertical fractures, it is not to be inferred that the present fracturing techniques result in producing a vertical fracture. The types of fracture which are created are not known with certainty in every case. Some are believed to be horizontal, others inclined along bedding planes, and some data indicate vertical fracturing. Each fracture will probably exert a different influence on the sweep efficiency of the secondary recovery program; consequently each fractured well should perhaps be considered as a separate problem, requiring a careful analysis. Preliminary work on the effect of fractures on producing capacity of a well indicated that for practical purposes many fractures may be treated as having a nearly infinite permeability This assumption appears to be valid in some instances where the permeability of the fracture is only 10 or 100 times greater than the permeability of the matrix. It is known to depend on the type, orientation and length of the fracture. In realization that fractures of only 0.01 in. width have calculated permeabilities near 5,000 darcys, it is believed that many fractures may be considered as of near infinite permeability without incurring serious error. Primarily for this reason this study was made with fracture analogs of very great permeability compared to the matrix. FRACTURED SYSTEM ANALOG The pattern sweep efficiencies reported here were obtained with the aid of a potentiometric model. The application of this type model for solving reservoir problems has been described in the literature.1,2,3 The electrolyte reservoir was 20 in. wide by 30 in. long by approximately % in. deep. The liquid depth was constant, which corresponded to a constant permeability-feet product from the injection to the production well. The electrolyte reservoir was built to correspond to a unit in the line-drive pattern shown in Fig. 1. This figure shows part of an infinite array of wells having alternate rows of fractured and unfractured wells. The area within the dashed rectangle shows the area generally studied in the model. In using the model to represent a fractured system, a thin strip of copper was soldered to the well or wells and the length and orientation of the strip was made to conform to the vertical fracture under consideration.

Jan 1, 1955

By G C. Bolton

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCl in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By H. F. Walther

Basic electric-are furnace steel production mainly involves the use of two separate types of slags. The first, known as the "melt down" or oxidizing slag, which is in most cases removed from the furnace mechanically, and the heat finished under the second or deoxidizing slag, which is commonly known as the "finishing slag.'' The melt down slag is formed by the addition of lime or limestone to the charge, which combines with the oxides formed during the melting period and the product of any bottom erosion that may take place.

Jan 1, 1935

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

There are not many data about early coal production in Kentucky, but some legislative reports, early geological studies and occasional newspaper articles have left some figures. The earliest production with any authentic record is that of Lee County, the coal being boated down the Kentucky River to Frankfort. While never a large producer, this county has the longest record in the State. Production is recorded in several of the western coal counties in 1820, and in several others a few years later. The early production in Greenup County was for the iron furnaces operating there. Clay County had a large salt output in the early days and this required a large output, for those days, of coal; the amount of fuel is based on the quantity of salt. It will be noticed that several counties on the Ohio River produced considerable quantities of coal before the Civil War, much of it being consumed by the river steamers. Since the end of the war, these counties have never occupied the relatively important position they had prior to that time. All of the coal produced in the eastern mountain counties moved out of them by water before the war, and during that struggle nearly all mining was stopped. The growth of the railroads after the war greatly reduced the river traffic from these counties, and in some cases it was never renewed. The coal shipped from Lawrence County prior to 1861 all moved by water; after that date there was no production excepting for local use until 1879, and since that time, all shipments have been by rail. Some of the early railroad reports have been helpful in reporting shipments, but for the early years very few of them can be found, and after about 1879 the quantities reported cannot be identified as to origin. Pres. J. B. Hill, Louisville and Nashville Railroad, furnished all of the data available for his line. Sources of data are shown on Table 61; other figures are estimated. A list of early Kentucky mines is given in Table 13.

Jan 1, 1942

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By T. Bennett

Geothermal energy has the potential to provide 20% of the UK's annual average electricity generation capacity requirement. This article discusses the costs and potential benefits.

Jun 1, 2015

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By R. M. Asimow

The magnetization curves for specimezs containing superparmagnetic particles are considered. It is shown that the curves may differ from a Langezlin function because of particle anisotropy, particle interactions , and the presence of a size distribution of particles. The various causes of particle anisotropy are considered, and magnetization curves for specimens with cubic and uniaxial anisotropy are presented. The magnetization curves depend on the In the particle-size below 100A it is quite difficult to obtain quantitative size and shape information on precipitate particles. All of the available techniques have their limitations; however, quantitative applications of superparmagnetism have not been developed as fully as possible due to a lack of analysis of the complete magnetization curve. With such an analysis it appears possible to obtain from a single magnetization curve of a specimen containing randomly oriented SPM (superparamagnetic) particles a quantitative volume distribution and a description of the particle shape.* sign of the anisotropy energy and in the case of a negative uniaxial anisotropy (prolate spheroids) the resulting curves may differ very considerbly from a Langevin function. A graphical technique is developed whereby it is possible to separate out the effects of the size distribution, the particle interaction, and the particle anisotropy. Thus it is possible to obtain quantitative values for both the particle shape and the size distribution. Langevin function2 I/Is = ctnh(HVIs/k T)-k T/HVIS [ 1 ] where I, is the saturation magnetization, V the particle volume, H the applied field, T the particle temperature, k the Boltzmann constant, and I the magnetization in the direction of the applied field. Such behavior is rarely if ever observed in actual systems. One explanation for this is that the SPM particles do possess a significant anisotropy and thus the magnetic energy associated with the particle depends on the direction of magnetization in a more complicated way than for the isotropic particle of Eq. [I]. In general the magnetic energy E of an isolated SPM particle embedded in a nonmagnetic matrix can be expressed as a sum of several contributions: E = Eh + Ed+Es+Ec [2] where Eh is the external field energy, Ed the energy resulting from the particle demagnetizing factor, E, the magnetostriction energy, and E, the crystalline anisotropy energy. In each term we consider only the part dependent on the orientation of the magnetization vector and the particle axes as the shape of the magnetization curve will be determined by these contributions. Following the same procedure used in deriving the Langevin function,

Jan 1, 1965

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005

By John Brulia

"Definition of On-Site Security: All mandatory and non-mandatory, deterrent and loss control measures undertaken by an authorized explosives business tokeep its stocks of explosive materials and precursors from: • (1) THEFT • (2) LOSS"

Jan 1, 2006

In a country richly endowed in mineral wealth, Climax Arintco Mining Corporation's ICAMC) Dinkidi porphyry Au-Cu deposit in Nueva Vizcaya, Philippines, represents the most significant mineral discovery in this country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon, a region previously unassociated with porphyry -style mineralisation.Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.4 per cent copper. Regional exploration throughout CAMC's 37 000 hectare FTAA has identified a further 16 potential porphyry-related deposits.

Jan 1, 1997

By Cornelius J. Dwyer

It is possible to hold a very optimistic view of the future of the U.S. coal industry, and there are those in the coal industry who generally choose to do so. For example, a major coal company stated recently in its annual report, "Coal's prospects appear brighter today than at any period in the past." In order to continue in this state of euphoria, it is only necessary to remind oneself of the following "facts":

Jan 7, 1967

By C. H. Hitchcock

Report C6 of the Second Geological Survey of Pennsylvania, by Charles E. Hall, describes the rocks of the Philadelphia belt, and sets forth conclusions widely different from those derived by others from the study of similar strata along the same stratigraphical line. Mr. Hall classifies these rocks into three groups: First, the Philadelphia schists and gneisses, well shown within the city limits and

Jan 1, 1884

By K. Nielsen

The paper uses three examples to illustrate the challenges that the minerals industry is facing with regard to our image and the public?s perception of us. The paper then discusses communication with stakeholders as opposed to lecturing to the public and the authorities, and states that the industry needs to work more directly towards politicians and regulators as target groups. The conclusion is that we still have a way to go before the industry is doing enough to bring our message to the right people, but we are improving.

Jan 1, 2007

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018