Search Documents

Roles of Mineral Impurities and Sulfur in the Leaching Behaviour of Pre-Reduced Ilmenite Ores

Sep 13, 2010

By R. E. Gilchrist, R. R. Harvey, M. R. Dean

A simple and rapid three-component analysis procedure has been developed for use in fluid-flow studies. The method is based on refractive index measurements, combined with refractive dispersion measured between the Ha and H wave lengths. The procedure requires. calibration curves for the three-fluid system. The only restriction on the fluids employed is that only one be an aromatzc or olefinic compound. Individual sample measurements require only a few minutes. Composition results within the limits of accuracy required for fluid-flow analog studies are obtained. INTRODUCTION The simultaneous analysis of three-component mixtures is a problem often encountered in fluid-flow analog systems. In petroleum production research, the problem is usually encountered in experiments on the displacement of fluid from a porous medium. In the case of immiscible displacement, simple volumetric measurements of the produced fluids are usually sufficient, the analog fluids often being the actual reservoir fluids themselves — oil, water and gas. However, modern secondary recovery of petroleum sometimes involves production under miscible conditions, in which the oil is displaced by liquefied petroleum gas which, in turn, is displaced by dry gas. Since this type of displacement is done under conditions of pressure and temperature that are not easily reproduced in the laboratory, studies are often performed with analog fluids at essentially atmospheric pressure. Since the number of samples taken during one of these experiments is usually quite large, the time required for analysis becomes an important factor. In the past, the difficulty of conventional analysis has been avoided by the addition of various tracers to one or more of the components, or by the use of a tracer fluid as one of the components. With these techniques, a relatively large amount of analytical time is still required. Moreover, in the case of added tracers, the tracer material may migrate in part to one of the other fluids, may be adsorbed on the solid surfaces of the model, or may introduce side effects not characteristic of the prototype fluid. The substitution of a tracer fluid for one of the components can severely limit the choice of analog fluids. Optical refractometry provides a rapid and economical method of analysis of two-fluid systems or of monitoring small changes in composition of an essentially one-component system. Refractometric methods are capable of high degrees of accuracy, require only very small samples and can easily be adapted to automatic methods. They are not generally applicable, however, where three or more fluids are present over wide ranges of concentration. The method of three-component analysis described here has three essential characteristics. 1. It is based on refractometric measurements and thus preserves all of these desirable properties. 2. It does not make any stringent demands on the choice of fluids that can be analyzed. 3. It is capable of accuracy sufficient for fluid-flow analog studies. THEORETICAL The difference in the refractive index of a substance at two different wave lengths of light is known as its dispersivity. When the difference is taken between the specific refractions at the two wave lengths, the quantity is referred to as the specific dispersivity. Specific refraction was defined empirically by Gladstone and Dale1 as r = n-1/d....[1] where n is the index of refraction and d is the density. The definition is given more correctly by the expression r =n2-1/n2+1 1/d..........(2) 1References given at end of paper. MICIFTV OF PETROLEUM ENGINEER JOURNAL.

By K. Ono

A new process for extraction of titanium metal from its oxide is demonstrated. In this process, row material to be reduced is titanium oxide synthesized from ilmenite. The reducing agent is the Ca+CaCI2 two-phase mixture. TItanium is elaborated in the medium consisted of liquid Ca, Caq and solid TI02 at the temperature range 1200 to l300K by means of mixing mechanically the ingredients in the reactor into a smooth paste. Fluidity of the feed which enables continuous scheme depends on the CaCl2 content. The oxygen level of the reduced titanium is the range 500 to 1000 mass ppm varying with the operational conditions. The Ca+CaCI2 reducing agent is taken out from the electrolysis of CaC12 at 11401(, and this CaCl2 is produced by aqueous chemistry conversion using Cl2 gas recycled from the electrolysis.

Jan 1, 2001

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By G. T. Lapidus, R. Zárate-Gutiérrez

Selective leaching of lead from a Pb-Ag-Zn concentrate with hydrogen peroxide in citrate solutions was studied at room temperature. Leaching tests were performed, varying the H2O2 concentration and the solid-liquid ratio, holding the solution pH constant at 7, and the citrate concentration at 1 M. Lead extractions of 100 % were achieved with 4 and 5 times the stoichiometric quantity needed to form elemental sulfur, with only a small amount of metal impurities dissolved (Ag, Zn and Fe). The lead solubility limit at those conditions was found to be ~21 g L-1. X-ray diffraction analyses of the leach residues were free of galena (PbS), while other metal sulfides, such as sphalerite (ZnS), chalcopyrite (CuFeS2) and pyrite (FeS2), were basically unaffected.

Jan 1, 2014

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By Paul G. Dunn

Safe rapid drift development results principally in reducing exposure of underground workers to the working face. This reduction in exposure is not achieved until either the rock walls have been suitably scaled or sufficient support has been put in place. Rapid drifting enables quicker access to orebodies (increasing returns), higher production rates and a resultant lower cost of mining. The Mining Innovation, Rehabilitation And Applied Research Corporation (MIRARCO) has been developing technology and a methodology for safe rapid drift development within the underground metalliferous mining industry. In terms of rock scaling for underground metal mines, there is still considerable use of manual and mechanical impact rock scaling techniques. Two main issues result from this approach. The first is that in highly stressed or highly fractured ground, a decision has to be made as to when sufficient scaling has taken place. This is not always easy to do and hence operator judgment is a crucial element in this approach. During a baseline study of current rock scaling practices, a wide range of scaling practices were observed within five different underground mining operations; this demonstrates the difficulty inherent in the rock scaling quality decision making process. The second issue is related to the exposure of workers to freshly created rock surfaces. In manual scaling techniques this is unavoidable and despite the best scaling practices, accidents still occur. In an attempt to provide an alternative scaling technology, MIRARCO has been investigating highpressure water jet scaling for removing loose rock as part of the drift advance process. This technology not only provides a means by which scaling practices can be engineered (remove the loose material you want to in a given rock mass condition), it is also quicker and easily automated. Automating the scaling process removes workers from exposure to freshly created rock surfaces and also enhances the application of spray-on liners through improved adhesion of these support types to the rock surface. This paper describes the water jet scaling technology research and methodology for safe rapid drifting within the underground metaliferous mining industry and highlights the key issues and major drivers behind their continued development at MIRARCO.

May 1, 2004

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By George H. Cook

At first sight this subject seems to belong to pure theoretical geology, but examination will soon show that it has important practical and economic interest to the mining engineer. The conclusion that all the northern portions of our country, as well as of the eastern continent, have, in the later periods of geological history, been covered with a thick bed of ice, is now accepted by geologists. This bed of ice, except in its greater magnitude, was like the modern glaciers of the Alps, and other mountains which extend above the line of perpetual snow. The marks it has left upon the surface show that it was comparatively thin on its southern edge, but that its thickness was much greater a little further north, and that it was several thousand feet thick at its kenviest parts. This variation of its surface would give it a descending slope towards the south, and cause the mass of ice, like a semifluid substance, to move in that direction,

Jan 1, 1879

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By H Kurth

"The focus of this paper is on measuring the composition to improve mill feed quality to minimise the processing of waste, optimise process performance, reduce processing costs and minimise the generation of tailings.Technologies used since the 1990s in the cement and coal industries for measuring conveyed materials have been operationally proven and effectively derisked. Despite this the acceptance by the minerals industry has been very slow except in iron ore. Real-time penetrative full stream measurement using prompt gamma neutron activation analysis (PGNAA) for multielemental analysis and microwave transmission for real-time moisture analysis provide representative, tonnage weighted dry weight per cent results on a minute by minute basis. Analysis is unaffected by particle size, dust, layering/segregation, mineralogy and belt speed. The technologies are explained and performance examples given. The benefits derived from real-time compositional analysis are predicated upon a good understanding of deposit geology, mineralogical associations, waste to ore interfaces, amenability to mining, metallurgical processes and downstream customer requirements. Processing may include basic preparation in the case of direct shipping ores, minor beneficiation using simple upgrading methods, or concentration using more complex processing systems such as flotation, leaching or many others. The value of real-time data from primary crushed conveyed flows, using analysis of increments smaller than a single haul truck’s load, is very beneficial in process plants aiming to reduce waste processing, increasing feed grades and increasing metal recoveries. Grade variability can be utilised to divert conveyed increments of waste, direct shipping ore (DSO) quality material bypassing beneficiation, and subeconomic material amenable to upgrading diverted for further preconcentration by particle separation (sorting, heavy medium etc). Paybacks of a few months have been commonly achieved where the real-time technologies have been applied in the minerals sector. The paper outlines proven applications and case studies and proposes some innovative applications.Citation:Kurth, H, 2016. Measuring and Utilising Ore Quality Variability Using Real-time On-belt Elemental Analysis to Improve Mill Feed Quality, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Warrego copper ore characteristically contains 0.05-0.2% bismuth, which on upgrading produces a concentrate of approximately 1.3% bismuth. Early smelting of this concentrate (1973) was accomplished in a flash furnace (eliminating 92% of the bismuth in the con- centrate) and Top Blown Rotary Convertors (eliminating 85% of the bismuth in the matte). However 1.3% bismuth was considered the max- imLun bismuth level that could be treated. Geological evidence indicated that the bismuth level in~the copper ore would increase and that the bismuth level in the Warrego ore would be 0.3-0.7% bismuth. Treating these ores would produce a copper concentrate with bismuth levels far in excess of those accept- able to the smelter and still produce low bismuth content blister (limit 0.03% bismuth).

Jan 1, 1984

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By Miyashita T, Yamamoto R, Kishimoto s

Following considerations of the effect of furnace size on pressure loss, pressure loss in front of tuyeres, gas flow in the lower parts of the furnace, the distribution of the burden and the gas flow in large blast furnaces is examined with particular reference to the burden distribution at the throat and the gas flow at high production rates. Improvement of gas flow is related to application of super-high top pressure and the use of moveable armour. A brief description of the NKK type moveable armour is given and its use in controlling the gas flow outlined. The operating results under controlled gas flow show an increase in production of Fukuyama No. 5 BF from 9,200 tpd to 11,000 tpd with a decrease in the fuel rate from 490 kg/thm to 460 kg/thm.

Jan 1, 1975