Search Documents

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By Maurice Deul

Limestone can be used effectively in treating acid mine water. Aside from a lower cost than for other treatment agents, limestone has the advantages of easy storage and effectiveness even when impure and in slack sizes. Limestone incorporated into waste piles in layers or as riprap can inhibit acid formation; limestone rubble packed in a mine entry offers promise in formation of a low-cost autogenous resilient seal.

Jan 1, 1974

By Luis de la Pe[n]a Porth

The present process refers to a method for efficiently obtaining high purity metallic copper from copper ammonium sulfite. Essentially, this process consists of submitting the copper ammonium sulfite to the action of heat and pressure with the object of obtaining by the decomposition of it, metallic copper, ammonium sulfate, sulfur dioxide, and sulfuric acid.

Jan 1, 1974

By Atkinson D

This paper briefly outlines the develop ment of the froth flotation plant at Coal Cliff Colliery. The plant was superimposed onto the original flow sheet in which fines were merely thickened and filtered. Test work leading up to the installation is described and the final layout is discussed. Details of the concentrate and tailings systems are given. Preliminary results of a further extension involving the use of a Davcra flotation machine are also given.

Jan 1, 1974

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By David L. Veith

Caustic scrubbing followed by silica flotation with cationic ether primary amine proved effective in upgrading commercial magnetic concentrates to supergrade products containing 2 percent SiO2, or less. Samples representing 41 million long tons per year of commercial magnetic concentrates from the Lake Superior region were tested by the Bureau of Mines. Bench-scale and pilot plant research indicated an estimated potential of 32 million long tons per year of superconcentrates to be available. Two pilot plant investigations yielded superconcentrates containing 1.1 and 1.9 percent SiO2 that were derived from commercial concentrates containing 7.0 and 4.2 percent SiO2, respectively. Corresponding iron recoveries were 90 and 93 percent at reagent costs of just over 33 cents per long ton of superconcentrates produced. Additional sources evaluated on a bench scale resulted in iron recoveries of 72 to 95 percent in products containing 1.7 to 2.0 percent Si02. Although reagent cost ranged up to 60 cents per long ton of superconcentrate, it is probable that these costs would be reduced in plant applications where benefits are derived from material and reagent recycle.

Jan 1, 1974

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By T. O. Llewellyn

The Bureau of Mines investigated the use of a heavy liquid in combination with fluid cyclones to separate brucite from a Nevada ore on a continuous basis, using a mixture of dibromomethane and trichloroethylene having a density of 2.44 grams per cubic centimeter. Single-stage cyclone separation produced a concentrate that contained 84 percent of the total magnesia at a grade, on a calcined basis, of 95.6 percent MgO.

Jan 1, 1974

By Roy Greenfield

Estimates are given for the distance from a seismometer at which a miner can probably be detected. The procedure in making these estimates was to first establish the natural noise levels at the output of a surface seismometer for the 25 to 100 Hz frequency passband. The noise levels give the range of values which may be expected in areas with no man-made noise. For each noise level, we give the detection threshold which, when exceeded, indicates that a signal has been received. Based on the signals recorded by Westinghouse, curves are given which show the peak signal amplitude as a function of source- to-receiver distance (slant range). Curves are given for the Westinghouse seismic thumper, a 50-pound timber, and a sledge. For a given type of source, the receive signal strength depends more strongly on slant range than on any other factor. However, there is approximately a five-to-one scatter in the amplitudes. Thus, further study of factors affecting the signal amplitude might allow better estimates to be made for any particular geological setting. Combining the signal amplitude with the detection thresholds for the different noise conditions gives the distances at which a miner should be detected. These are given in Table l* below. [ ] The text also gives the increase in detection ranges which should occur if steps are taken to increase S/N by 10 dB. We feel that 10 dB is a conservative estimate of the improvement possible. During an actual rescue operation, the seismic crew and system should be capable of making on-site estimates of their detection capability, based on measurements of the site noise, and upon the best available estimates of the

Jan 1, 1974

By G. R. Green, R. C. McDonald

The International Nickel Co., Ontario Div. mines, faced with rising production requirements, short labor supply, and ever increasing labor costs turned to mechanized mining for a solution to its problems. The degree of mechanization of ore removal has increased from 1966 with the purchase of the first diesel-powered load-haul-dump (LHD) machine to the present, with over 53% of all underground production handled by these units. Keeping pace with mechanized ore removal, there has been a parallel development of drilling equipment to complement the mucking units. This paper deals with the applications and economic advantages of mechanized drilling at the underground mines of Inco, Ontario Div. It covers the use of various types of mechanized drills in such mining methods as cut-and-fill, induced block caving, and sublevel caving. The economics of raise boring are also discussed.

Jan 1, 1974

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texasgulf, Inc., Operates the Kidd Creek Mine, Concentrator and Zinc Plant at Timmins, Ontario. Two different ore types are mined and milled to produce concentrates of copper, zinc, lead and tin. The ores are processed at the Concentrator in three separate individual milling circuits, each with the capacity to treat up to 3500 tons per day. Two circuits treat copper-zinc ore 1t an average combined rate of 6500 tons per day and the third circuit treats 3500 tons per day of silver-lead zinc ore. Conventional crushing, grinding and flotation procedures are followed. The purpose of this paper is to describe Ecstall's experience with rubber mill linings in the grinding circuits.CrushingBoth ores are crushed to minus 6 inches at the Mine and delivered by rail to the Concentrator where they are reduced by secondary and tertiary crushing to minus 5/8 inch.GrindingThe crushed ores are prepared for selective flotation by grinding with rod mills and two stages of ball milling. flotation circuit middling products are reground in regrind mills prior to further treatment. A typical flowsheet of one of the grinding circuits is shown in Figure 1.All the grinding units are Allis-Chalmers Mills. The rod mills are 10 1/2 feet diameter by 16 feet long. Both the primary and secondary ball mills are 12 feet diameter by 18 feet long and all regrind mills are 6 feet diameter by 12 feet long. The primary mills are charged with 1 13/16 inch forged balls. Secondary mills are charged with 1 1/2 inch forged balls and the regrind mills are charged with 1 inch forged balls. All cyclones are Kreb units. The primary cyclones are Dl5B hydrocyclones, the secondary cyclones are D6B hydrocyclones and all regrind cyclones are D6B hydrocyclones."

Jan 1, 1974

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By Kenneth L. Schellie

In preplanning the reclamation of a pit or quarry the geology of the site is the name of the game! The planner must know the parameters of the deposit, the quantity and kind of earth materials to be removed, and the amount and nature of the materials to be left behind or wasted as the result of processing the marketable product. With many states and most local jurisdictions requiring reclamation plans prior to the issuance of mining permits, the need for accurate and complete data concerning the geology of the site becomes increasingly important. The producer need only know that marketable materials are available in sufficient quantity to make the mining operation economically feasible-the planner, in order that the land may be reshaped for a useful purpose, must have reasonably precise information as to the dimensions and configurations of the pit or quarry following extraction and the amount and type of materials available on the site (or in some cases offsite as well). Therefore the geology of the site is of major significance in determining the land forms and use capabilities of the property upon completion of the mining process.

Jan 1, 1974

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By R. H. Jefferson

This Bureau of Mines report describes a series of rapid wet chemical methods for the analysis of blast furnace slags. A "complete" analysis for total iron, manganese, silica, lime (calcium oxide), magnesia (magnesium oxide), sulfur, and mixed oxides (R203) can be routinely performed in less than 3 hours. These methods were employed as the analytical control procedures for the Bureau's experimental blast furnace operations and have been satisfactorily applied to the analysis of other slags and calcareous materials.

Jan 1, 1974

By Thomas G. Langton

The demand for mineral raw materials, especially in the major industrialized nations, has grown rapidly during the past three decades. One consequence of this growth has been an increasing reliance by the large industrialized countries upon nondomestic mineral supplies. These mineral supplies, to a large extent, have been developed by capital from the major industrialized countries. Until recently, most foreign mining ventures were either wholly-owned subsidiaries or joint ventures between two or more mining companies. The recent rise of economic nationalism has substantially changed the business climate and parameters under which foreign investors operate. This paper describes some of the underlying reasons for this change and notes how investors have adapted to the new business conditions.

Jan 1, 1974

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974

By Peter G. Groer

Several methods1-3 are being used to determine the WL and individual Rn-daughter concentrations in uranium mine atmospheres. The best of these methods is the one given in Ref. 3. According to this method, the WL and the Rn-daughter concentrations are determined from the total a-counts observed during three consecutive time intervals. Its only disadvantage lies in the fact that rather involved calculations are necessary to convert the observed counts into WL or pCi/l (picocuries per liter). There are, however, counting intervals that give simple weighting coefficients for the observed counts. This fact makes it possible to convert from a-counts to WL or pCi/l with the aid of a graph. After some trial runs on a computer the following equations emerged as the basis for the most practical procedure: [ ] NA, N.., and & stand for the number of RaA, RaB, and RaC atoms per liter of air. C(t1,t2) denotes the counts observed from time t. to time t2 (in minutes) after the end of the 5-min sampling period. E is the detector efficiency and V is the flow rate in liters per minute. With an accuracy loss of less than -5% one finds from [Eq. 1] by adding the corresponding terms: If the WL would have been calculated according to [Eq. 2] instead of using the graph, the result would have been 0.31. Since the values used for C's under [Eq. 3] represent the exact number of counts from a Rn-daughter mixture in equilibrium with 100/3 pCi of Rn the exact WL of this mixture can be calculated easily. The exact value is: [ ] This shows that the method is quite accurate for the 0.3 WL domain. The precision of the method excluding errors made in reading the graph can be estimated with the help of the following formula: [ ]

Jan 1, 1974