Search Documents

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth's surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last 15 years. Fifteen years ago a 21/4-cu-yd front end loader was the largest standard machine you could purchase. Today there are two commercially available 15-yd front end loaders and many 10-yd loaders. The estimated total worldwide market for all front end loaders over 1 cu yd has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 and 24-cu-yd front end loaders in prototype form. It is not inconceivable that within another 15 years there will be front end loaders in the 50-cu-yd class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry, and the design criteria are being directed at this market area. The costs of these larger loaders may be greater per unit of capacity, but it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Table 1 are data for U.S. production of front end loaders (5 to 6-cu-yd class and 10-cu-yd class) and U.S. production of cable-operated, crawler-mounted power shovels, draglines, and cranes (11/z to 5-cu-yd class) for the years 1965 and 1970 (Source: Bureau of Census, U.S. Department of Commerce). Many believe that the decline in shovel production, in particular, is due at least in part to the acceptance of the front end loader as a primary production tool. However, the foregoing comparison is for a smaller shovel class than for front end loaders. It has generally been a rule of thumb that a front end loader is competitive on a cost and production basis with a shovel when it is approximately twice as large as the shovel. This same relationship may not hold true with the larger 10 to 15-cu-yd electric shovels, but at some point, direct competition will probably occur. Current Trends There are many trends today that are significant. One major usage trend in large front end loaders involves load and carry operations. This application is defined as "performing the functions of loading, hauling and dumping with one machine over distances within its economical limits." Many people are using front end loaders to transport material as well as load it. It is estimated that nearly half of all 10-cu-yd front end loaders sold in 1970 went into primary load and carry work. Many times, significant savings result from using the load and carry system, instead of small truck and shovel operations, for distances in excess of 1000 ft. Strip mining in coal utilizes great numbers of front end loaders in this manner. In-pit crushing of limestone is developing on an ever-increasing level, especially in Europe, and this stimulates interest in load and carry operations. In Table 2 is a cost example for 10-cu-yd front end loader in a limestone quarry. More than likely, load and carry use will continue to increase over the next few years. While some types of mining do not lend themselves to load and carry in the pit, such areas as surge piles are applicable and should be studied. In the area of machine operating cost reduction, there

Jan 1, 1974

By G. I. Mathieu, R. W. Bruce

Flotation schemes for the separation of molybdenite from other minerals are based on utilizing the Inherent hydrophobicity of molygdenite (Fuerstenau1). This natural floatability was attributed to the crystalline structure of molybdenite by Gaudin et al.2 who suggested that any surface formed by the rupture of van der Wall's bonds should be hydrophobic and, therefore, naturally floatable. Other authors argued that "natural floatability" is dependent of adsorption of hydrocarbon ions and/or molecu1es on the surface of the minerals. This theory, albeit-c questioned 1,2 has long been recognized in actual practice of molybdenite flotation as the latter in carried out with hydrocarbons, such as fuel oil, kerosene and stove oil. Although conferring ready floatability to molybdenite, these presents generally have little effect on other sulphides and silicates. However, talc is a noteworthy exception because of its innate floatability4. Not withstanding the reason for this behavior which has also been attributed to crystal structure2 its end results as in the case of molybdenite is an immediate flotation response to frothing oils arid kerosene, as was observed by Baranovski5, Sutherland and Wark6.

Jan 1, 1974

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By Roshan Bhappu, Laszlo Dudas, Herman Maass

Introduction Chemical and mineralogical constitution play a very important role in the processing of ores because they dictate the method, either physical or chemical, for extracting the mineral or metal. Similarly, the mineralogical nature of the ore, especially the grain size of the valuable minerals, is very important in its processing. The fineness of the grain may be such that physical separation pro- cesses may be eliminated in preference to chemical techniques. In the past, very little attention has been devoted to the geo- logical and mineralogical occurrences which may be potential sources of ores by both the geologist and mineral processing engineer. On the one hand, geologists have devoted less attention to lower grade, complex mineral deposits, and, therefore, may have inadvertently curtailed an exploration 2rogra.m. On the other hand, the metal- lurgists have neglected to study in detail the geological environ- ments and mineralization of potential ores with the view of deter- mining the critical parameter that could assist in economically processing complex submarginal deposits. In the final analysis, a chemical processing technique converts the valuable metals to a mobile state under conditions similar to those which deposited originally in the host rock. The relationship between ore-genesis and chemical processing is close when the process of mineral or metal deposition in a particular ore deposit is understood--putting the metal in solution by reversing the process of deposition is re- latively easy. For this reason, some researchers and educators have been stressing the importance of ore-genesis, geochemistry, mineral equilibria, and ionic equilibria in studying and explaining the

Jan 1, 1974

By Jaime Lomelin

[First of all I want to thank the Society of Mining Engineers of AIME for the opportunity to present what Industrias Penoles, S.A. is doing in Mexico to reach the basic objetive of the enterprise without compromising, in short or long term, the living conditions of the community or attempting in an irreversible form against Nature. Industrias Penoles, S.A. is one of the largest mining and metallurgical companies in Mexico. It was founded in 1887 and at the turn of the century installed a lead smelting operation close to the village of Torreon, which became city five years after the start up of the Penoles smelter. Now Torreon has a population close to 300,000 inhabitants. In 1974 Penoles is still the largest industry in Torreon and the dynamic growth of the city is close related to this factor. Today Penoles in Torreon has a lead smelter with a capacity of 130,000 metric tons/year of bullion, an electrolitic zinc plant of 105,000 metric ton/year, and it is modernizing its lead smelter to control pollution and expand it to 190,000 metric ton/year of bullion including all the services and refinery. The Penoles complex in Torreon is the biggest in the non-ferrous metals field in Latinoamérica.]

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

1 Abaibanel, S , "Deflection of Confining Walls by Explosive Loads," Israel Jour. Technology, vol. 4, n. 1, Feb 1966. 2 Albertoni, S and others, "Numerical Computation Methods for Implosion Processes," EURATOM Proc. of the Conf. on Megagauss Magnetic Field Generation by Explosives and Related Experiments, Milan (Italy), July, 1966. 3 Alexander, S. J , and Hambly, E. C., "Design of Structures to Withstand Gaseous Explosions," Concrete, vol. 4, n 2, Feb. and March, 1970. 4 Anonymous (Belgium Institute of Extractive Industries), "Report for 1968 (covering approved equipment for Belgiums gassy coal mines)," (in French and Flemish), Amales des Mines de Belgigue, n. 6, June, 1969. 5. Anonymous (Ghent Univ., Belgium), "The Welding of Very Thick Steels. Margin of Uncertainty of the Robertson Test," EURATOM Contract 042-61-9-RDB, May 20, 1965. 6. Anonymous, "Inportance of the Nature and Size of Weld Defects with Regard to the Mechanical Strength of Pressure Vessels, (in Flemish), A. Sys. Rev. Soudure, vol. 27, n. 3, 1971. 7. Anonymous (Raentgen Technische Dienst N V., Rotterdam), "Non¬Destructive Welding," Quarterly Report No 13, EURAEC - 1342, March 30, 1965. 8. Anonymous (Staff, USBM Safety Research Center), "Research and Technologic Work on Explosives, Explosions, and Flames: Fiscal year 1969," USBM IC8492, 1970. 9. Anonymous, "Symposium on Flameproofing Intrinsic Safety and Other Safeguards in Electrical Instrument Practice, April 27, 1962," IEEE Conf. Report Ser. 3, 1963. 10. Anonymous, "Unfired Pressure Vessels," ASME Pressure Vessel Code, Sec. 8, 1965. 11. Anonymous, "Unusual Pressure Relief Devices," Industrial and Engineering Chemistry, vol 54, n. 1, Jan., 1962. 12. Archer, G. L., "Design to Avoid Brittle Fracture in Welded Structures," Paper No. 4, Improving Welded Prod Design, vol. 1, Welding Inst., Cambridge, England, 1971. 13. Bailey, F. C., "Buckling and Failure Strength of Plating Panels Loaded in Shear," Final Report NASA Contract NObs-72290, Lessels and Assoc., Inc., Waltham, Mass., Sept. 20, 1963.

Jan 1, 1974

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974

By Frank E. Dalton

The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves an area of approximately 860 square miles and collects and processes used water from the city of Chicago and 116 surrounding communities. As a public agency, the MSDGC -Serves a population equivalent to 10 million people which is composed of 5.5 million people and an industrial wasteload equivalent to an additional 4-1/2 million people. -Provides 400 miles of intercepting sewers and tunnels ranging in diameter from 12 inches to 24 feet. -Operates 71 miles of navigable waterways and channels conncecting the Atlantic Ocean and the Great Lakes with the Gulf of Mexico and 6,000 miles of inland waterways. -Maintains the largest water reclamation plant in the world. -Processes 1,380,000,000 of used water daily and removes approximately 1,000 dry tons of organic solids each day. -Has spent approximately 700 million dollars in capital improvements to date, and will require expenditures in excess of 3 billion dollars (including over one-half billion dollars in tunnels) to meet existing federal and state water quality standards.

Jan 1, 1974

To improve a miner's chances for survival in an emergency by providing an improved self-rescuer device that functions in a toxic or oxygen-deficient atmosphere. The Approach: Development of a compact, lightweight apparatus which produces oxygen by using the wearer's breath in a chemical reaction. How It Works: The device is designed to cause the user's breath, which contains water vapor and carbon dioxide, to react with potassium superoxide (K02) to produce oxygen in quantities sufficient to sustain the wearer for one hour. The system is a closed circuit and does not depend on "screening" of noxious gases. To use the device, the miner opens the top and

Jan 1, 1974

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

Until the early 1960s the world aluminium industry was dominated by six principle pro- ducers with integrated activities from bauxite mining to aluminium production. The growth in consumption of aluminium since that time and the emergence of additional producers has broadened the market for bauxite. In addition the increase in the optimum size of alumina refin- eries has influenced competing metal producers to unite in large joint ventures to minimize alumina costs. From these bases the paper examines present and likely future markets for Australian bauxite; differing marketing phil- osophies for serving those markets; factors influencing successful marketing; and the sources and relative strength of competition which Australia faces.

Jan 1, 1974

By Barber J

The manganese ore of Groote Eylandt is a shallow sedimentary deposit of Cretaceous age. There are a number of deposits which vary greatly in ore texture, density, percentage of matrix and thickness. The thickness in the present five operating quarries varies from 1-5 metres. The mine output in 1973 was 3 million tonnes of which 60% was blasted, the remainder ripped and bulldozed. The shallow deposit and its varying thickness create rather unique blasting problems which must be overcome in order to produce a minimum overall mining cost but not necessarily resulting in a minimum drilling and blasting cost per tonne. Future planning envisages the introduction of site mixed slurry explosives following test work and the application of a twin boom single operator rotary percussion drill. The paper outlines the overall developments,present and envisaged practices and the reasons for these changes.

Jan 1, 1974

By H. H. Fukubayashi

This Bureau of Mines report describes the development of a pyrometallurgical process for the recovery of the zinc and lead contained in brass smelter flue dusts, which constitute a recycling or disposal problem. Tests on brass flue dust from several sources were made in a quartz tube, heated by an electric furnace to temperatures as high as 1,050° C. The dusts were mixed with carbon and heated in an oxygen-free atmosphere. It was demonstrated that 98 pct of the zinc and 12 to 25 pct of the lead, both in the metallic state, could readily be removed from the dusts. It was also found that 75 pct of the zinc could be recovered, with less than 0.1 pct of the lead, in the absence of chlorides. Pelletization techniques were investigated and 0.6 inch pellets were found to be optimal. Pelletizing results in a tenfold reduction in volume.

Jan 1, 1974

By Palmer King

The increased emphasis on environmental protection, together with the exorbitant costs, or in many urban areas the complete unavailability of surface space, has resulted in a burgeoning demand for greater use of underground space. More and more, those considering new or expanded facilities are looking toward the possibility of utilizing underground space for communications installations, for transportation of people, industrial products, water, sewage and energy, and for industrial installations. Happily, this growing demand for use of underground space is accompanied by fast forward strides looking toward more efficient underground excavation techniques. The tunnel boring machine is already here and where ground conditions are suitable for its use it can greatly reduce the cost of underground excavations, savings of one-third or more often being realized. Research is underway involving excavation by use of laser beams, jetting, vibrations, improvement of tunnel boring machines to make possible the excavation of harder rock, and other advanced techniques. The Engineering Foundation estimated in 1973 that tunneling costs can be reduced as much as 30 percent by rapid excavation methods which are expected to be developed through ongoing research programs in the next few years. Your American Society of Civil Engineers reported in 1973 that $60 billion per year, or 15 percent of the gross national product, could be saved if facilities required to support life were located in the subsurface. Studies looking toward improved contracting practices are going on under the sponsorship of the National Academy of Sciences, and Mr. Al Mathews who is heading this program will address you during this session on the status of this project. I myself am a member of Mr. Mathews' study group and, considering the human element involved, it is too early to make predictions as to what can be accomplished in the way of savings in costs of

Jan 1, 1974