Search Documents

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By J. A. Eisele

The Bureau of Hines conducted a bench-scale investigation of a concentrated H2S04 reaction for recovering and separating rare-earth elements, barium, and strontium from a bastnasite ore and byproduct. Barium and strontium were dissolved in the concentrated acid and precipitated as a mixed product by water dilution. Separation of strontium from barium was effected by reaction with Na2C03 solution, followed by a dilute acid leach of the SrC03 formed. After removing the barium and strontium from bastnäsite are, the rare-earth elements were roasted to water-soluble sulfates. The rare-earth sulfate solution was subsequently processed by solvent extraction to produce rare-earth oxides low in lead and magnesium.

Jan 1, 1974

By George A. Savanick

Coal mine roof shales fracture preferentially at slickensided surfaces because of weak or nonexistent adhesion between two slickensided rock surfaces. The purpose of this Bureau of Mines research was to characterize chemically the thin film of smooth, glossy material that makes up the slickenside. This material was analyzed by electron spectroscopy and ion scattering spectrometry while in place on the rock surface and by standard methods of quantitative chemical analysis on concentrate removed from the rock. These analyses showed that the chemistry and mineralogy of the slickensides are similar to that of the adjacent shale.

Jan 1, 1974

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By R. F. Stewart

A nuclear meter based on measurement of prompt capture gamma rays is being developed for monitoring the sulfur content of coal streams. Equipment has been built to measure sulfur rapidly, and methods have been devised to compensate for changes in moisture, ash, and bulk density of coal flowing through a bin. Pilot plant tests of the system with various additives to different coals show a precision and accuracy of 0.02 percent sulfur and 0.04 percent sulfur, respectively. Based on these results, a hardwired meter has been fabricated for testing in a commercial coal preparation plant.

Jan 1, 1974

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

We have been exploring for minerals in Australia for over 100 years and our methods are constantly improving - but why do we pros- pect? Is the effort justified? Obviously the main motive is economic gain. It is now and always has been but conditions are changing rapidly. Once it was the prospector who could cash the nugget. Then it was the syndicate, the small company, an amalgamation of small companies, the large company, the corporation; the multinational corporation - where do we go from there? Early there was personal satisfaction and excitement in out-door activity which gave scope for individual energy, hope and in some cases reward. There still remains the satisfaction, either individual or corporate that a mineral discovery creates new wealth and makes a contribution to the nation's well being. Parallel with developments has always been the growth of restraints on exploration, frequently out of phase with the current mineral developments - miners' rights, licences, titles, royalties, mining laws and regulations, taxation etc. As the operations have become more complex so the restraints have become more confining until it is now very necessary to question whether the chances of economic gain justify the risk and responsibility of mounting costly mineral exploration leading-to extensive capital development.

Jan 1, 1974

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

Statistics show that despite a low lost-time accident rate there is a high fatality rate from falls of ground in pillar extraction work. Investigation of accidents indicates that in many cases the planned ex- traction cycle has been ignored. Better training, supervision, and personnel protection and where possible changed systems are suggested as a means of improving safety and achieving better Results.

Jan 1, 1974

The development of the Moura Coal Preparation Plant is described, commencing with the first'stage of the plant commissioned in 1963. The subsequent expansion stages are traced through to October, 1973. The plant has undergone frequent stages of expansion and modification and this process is continuing. The development programme for 1974 is described as proposed in late 1973. The characteristics of the Moura and Kianga field coal seams with respect to washability are summarised and some comment is made on the blending of these coals prior to washing, to ensure production of export grade coal within specification.

Jan 1, 1974

By D. J. Oswald, J. G. Ziegler

It is of common knowledge that loading within a grinding mill, whether ball, rod, pebble, or autogenous, is directly related to the lubrication back pressure developed between the mill journal and bearing shoe during mill operation. The merits of both forced-feed and gravitational-feed bearing lubrication methods are discussed with particular emphasis directed toward their applicability to continuous grinding mill inventory control. Data obtained from wet grinding mill applications in the cement and mining industries is presented to more clearly define the influence of such variables as feed consistency, slurry viscosity, mill retention, bearing oil temperature, grind fineness, and grinding media wear on the measured journal lubrication back pressure during automatic mill feed control. Finally, various grinding mill control schemes for maintaining constant mill loading and consequently optimizing mill operating efficiency are discussed and evaluated as to their advantages and/or disadvantages.

Jan 1, 1974

By Abbas Ali Daneshy

A study of the mechanics of hydraulic fracturing shows the fracture initiation pressure to be a function of the in-situ principal stresses, the formation and fluid properties, and how the wellbore has been completed. The orientation of the hydraulic fracture is perpendicular to the least in-situ principal stress. The geometry of the induced fracture depends on the treatment fluid properties, the injection rate and volume, fluid leak-off and formation properties.

Jan 1, 1974

By William G. Schultz

Sylvite of Canada, a division of Hudson Bay Mining and Smelting Co., operates a new 8500-tpd potash mine ten miles northeast of Rocanville, Sask. This mine, employing less than 60 men in its underground maintenance, engineering, and production operations probably ranks as one of the most highly mechanized and automated mining operations in the world. Access to the flat lying potash bed is through two 16-ft-diam concrete and steel lined shafts 3300 ft deep. The backbone of the operation is two 258-ton, 1500-hp continuous mining machines capable of mining in excess of 700 tph per machine while employing extensible conveyors for haulage. This production capability is complemented by a completely automated haulage, storage, and hoisting system. Of the other unique features of this operation, the principal ones are that the mine was designed and developed by the people that are currently operating it and from the time the shafts were commissioned, the mine was completely developed, equipped, and brought to full production in less than six months.

Jan 1, 1974

By E. T. Turkdogan, L. S. Darken, R. G. Olsson, H. A. Wriedt

Several aspects of the calcination of Michigan limestone were investigated: the rate of calcination of limestone spheres with diameters from 1.8 to 14 cm at temperatures from 800° to 1200°C by a thermogravimetric method; the temperature profile across limestone during calcination; the excess pressure developed in the interior of the stone during calcination; the pore surface area, pore volume, and effective gas diffusivity in burnt lime; and the microstructure of polished and fracture surfaces. It is found that, over a wide range of experimental conditions, the difference between the surface and center temperatures remains essentially unchanged during the latter half of calcination. From the rate of weight loss after about 50% calcination, the value 0.00126 cal per cm sec degree is found for the effective thermal conductivity of burnt lime. From the excess internal pressure measurements, i.e., 0.4 to 6 cm Hg at 800° to 1200°C, the permeability of burnt lime is estimated to be within the range 8 X 10-' to 5 X 10' sq cm. With increasing temperature and time of calcination, the pore structure of burnt lime coarsens as indicated by a decrease in the pore surface area, pore volume, and an increase in the average pore size. For the temperature range 600° to 835°C the ratio (effective gas diffusivity/molecular diffusivity) is about 0.18.

Jan 1, 1974

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By Guillermo P. Selas

Perhaps this is the first time that an analysis of the industrial minerals panorama has been made in Mexico for that type of commodities. Because the non-metallic minerals lack the glamour of the metallic minerals and are usually of less unit value than metallics, a comparative study of these commodities has seldom been attempted. Sulphur, fluorite, barite and few others are an exception. Consequently, the statistics on the lowest per unit value industrial minerals, such as limestone, dolomite, gravels, sands, etc., are usually scarce and not always accurate. The following, then, will be an attempt to show a general status of the industrial minerals in Mexico with due reservations regarding volumes and values. According to Kruger (1971), this group of minerals surprisingly very little known, and called non-metallics because the lack of metallic luster, is the largest group of the mineral kingdom. It constitutes perhaps 75% of all the mineral varieties. For the most part, these minerals are compounds of common acids, sulphides, hydroxides and two elements carbon and sulphur. The list of non-metallic minerals is therefore very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulphates and less commonly arsenates, chromates, molybdates, sulphides, tungstates and vanadates. The latter group and many of the oxides are sought usually for their metal content.

Jan 1, 1974

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By T. M. Evers, R. P. Van Den Berg

Ancient mining in Southern Africa, with reference to a copper mine in the Harmony Block, north-eastern Transvaal T. M. EVERS. B.A. (Birm.) (Visitor) and R. P. VAN DEN BERG. B.Sc. (Wits.) (Visitor) A recently discovered mine on the farms Harmony 24 and 25 in the Letaba district has been investigated archaeologically by T. M. Evers and geologically by R. P. van den Berg. The archaeological investigations shed light on the mining techniques and accompanying metallurgical techniques, while the geological investigations give information on the structure and mineralization of the mine. Comparisons with other investigated ancient workings show that mining was well understood in Iron Age times, before the African peoples had any contact with Europeans.

Jan 1, 1974