Search Documents

By Joseph M. Chelini

A cash-flow factor is any figure acquired in an evaluation that effects the cash flow potential of an eventual operation. Table I is a list of some of these cash-flow factors. There are more, such as, the payments and penalties in a smelter schedule if the concentrate would be sent to a smelter. During an evaluation it is necessary to maintain a two-way flow of communication between the evaluation people and financing people. To accomplish this, it is necessary to translate the vocabulary of the evaluating people into the vocabulary of the financing people, or geologic and engineering jargon into dollars and cents. This is done by cash-flow studies in which cash-flow factors are input, which when logically manipulated using accepted rules and procedures of accounting, provide an output in dollars and cents.

Jan 5, 1972

By Garry M. Hughes

Sherritt's new, 3000 tpd, copper- zinc Fox mine is situated 30 miles southwest of Lynn Lake. The copper-zinc orebody is part of a large body of massive and semi-massive sulfides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9s Fe) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The average sulfide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content. Surface diamond drilling indicated an orebody containing 12,269,000 tons grading 1.74% Cu and 2.35% Zn to the 2000 ft level. Underground drilling established the tonnage at 11,- 300,000 tons containing 1.96% Cu and 2.74% Zn.

Jan 4, 1972

By Donald A. Cumming

Since the first major mine development, the company has continually looked for ways of improving drifting methods. The planned increase in production to 60,000 tpd, and the lack of trained personnel, requires new development methods to maintain this high production rate. In order to finish the drifting on the 2015 and 2075 levels, a total of 59,000 ft is required, or two years at the present rate.

Jan 4, 1972

By J. H. Venter

The accuracy of estimation from samples of ore in bulk By J. H. Venter Published in the Journal April 1972. ERRATA: Equation (1) should read... Equation (3) should read .... line following "Duscussion" Delete" .... Insert... above "References" "Discussion". Replace .... tenth DISCUSSION M. DA VID Professor Venter has proposed a formula to compute the variance of the estimated grade of a lot of broken ore, and interesting comments on the relevance of the formula and suggestions for developments are made by P. R. Janisch.

Jan 4, 1972

By George A. Roche

Investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria used to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of investment strategy for two of the three mutual funds sponsored by the Price organization and for its private clients. However, during the past five years inflation has accelerated due to a variety of factors including the inability of government to meet seemingly unlimited needs with limited revenue sources.

Jan 4, 1972

By Theodore H. Eyde

In the southwest porphyry copper province, the virgin prospect with good copper mineralization cropping out has disappeared. Future discoveries will require an increasingly sophisticated arsenal of exploration techniques and concepts. One of the latter, stratigraphic analysis, is a technique which is often overlooked. A surprising number of exploration geologists still think of porphyry copper deposits as occurring wholly within intrusive bodies such as quartz monzonite or granodiorite. Disseminated copper mineralization, though genetically related to intrusive rocks, can occur within both the intrusive and the intruded rocks. At present, as much as 30% of the total copper produced from disseminated copper deposits in the Southwest originate from the intruded rocks rather than the intrusive.

Jan 4, 1972

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

The recent dedication of Magma Copper Co.'s San Manuel, Ariz., electrolytic copper refinery and rod casting plant marks the culmination of a three year, $250 million expansion-modernization program. The new facilities will eventually permit an annual production of 200,000 tons of marketable copper for direct sale to fabricators. The Newmont Mining Corp. subsidiary will produce and market continuous cast 5/16 in. copper redraw rod, full plate cathode copper and sheared cathode plate under its own brand name. Among the four largest in the nation, the new refinery and plant, was built at a cost of $34 million and will be fully automated. In addition, all materials used in the plant will be recycled and no waste, discard or emissions will occur.

Jan 3, 1972

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

By Charles M. Brinckerhoff

When I first went to Arizona in 1925, mining was primarily an underground job. Ajo, Sacramento Hill in Bisbee and Jerome were the only open pit operations in the state. Thousands of men, however, were employed in underground mining at Morenci, Miami, Inspiration, Globe, Ray, Bisbee, and Superior. The grade of ore in the larger operations was about 1-1/2% copper while a few of the smaller ones mined ore better than 2% Cu. In Utah, the Bingham pit was doing well and growing; in Montana, the vein mines of Butte still yielded ore running 6% Cu.

Jan 3, 1972

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

By Thomas V. Falkie

Mining and exploration, in the year 1971, can be characterized as a year of politics and the beginning of an era of legislation. Certainly the activities of our state and federal lawmakers and international politicians over-shadowed technical developments, which are outlined in the following pages. The nationalization of the Chilean copper industry was the most far-reaching event of the year. Not only will it have an effect on international metal trade, but the nationalization will also affect the major mining companies in such a way as to cause strategic, managerial and technical adjustments in metal mining and exploration efforts in other parts of the world.

Jan 2, 1972

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By J. L. Weaver

The spiraling rate in phosphate rock demand during the period 1957 to 1967 led producers to expect a continuation of a high growth rate. Consequently they expanded production capacity to meet the expected demand. Both the domestic and the world demand has shown little growth over the past three years. Florida producers operating at less than 75% of installed mining capacity, produce all that their markets will absorb. We expect that the nest few years will bring only a slight improvement in this condition. An increased demand in the domestic agricultural market will be partially offset by a continuing erosion in the export market.

Jan 1, 1972

By Jan M. Mutmansky

Simulation is a general term which commonly appears in the technical literature and which can have different meanings to different people. One interesting definition (9)* applicable in an engineering context is the following: "Simulation is the use of a model to study a problem." In most cases, the model referred to in the above definition is a simulation model constructed in a computer language and implemented on a computer in order to solve the problem under consideration. The application of computer simulation models to the study of problems in materials handling and earthmoving has been successful in the past. Generally speaking, this method has been used where the system to be studied has many variables and where the ability to predict the outcome of the system under different sets of conditions is difficult. The prime reason for using such a model is to evaluate the numerous likely ways of operating any particular system without the necessity of actually conducting full-scale field tests. The simulation model presented here is such an application made to the process of tunneling and, in particular, to the process of tunneling with a boring-type tunneling device. At first glance, the process of tunneling may not appear to be particularly complex and susceptible to study by a computer model. However, a close analysis of the tunneling process will reveal that it is rather complicated as a result of limitations placed upon the system by restricted space in the tunnel, geologic variations along the tunnel

Jan 1, 1972

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

By R. L. Every, A. G. Fonseca

"Sulphur deposition on the internal wall of a pipeline is caused by the temperature effect on the solubility of sulphur in the carrier fluid and is not due to particulate sulphur present. Deposition can be completely eliminated by proper insulation of the pipeline to prevent ""cold-spots"" and the resultant temperature gradient necessary for sulphur to precipitate from solution. Friction head losses for sulphur-condensate slurry systems are quite acceptable from a technical and economic standpoint and, in fact, are less than many present commercial slurry systems. Slurry transportation of sulphur in a hydrocarbon pipeline is a viable possibility and promises to have economic advantage over currently accepted transportation modes."

Jan 1, 1972

By Douglas R. Piteau

Douglas R. Piteau (Engineering Geologist, De Beers Corp., Kimberley, South Africa; Presently Consulting Specialist at Nchanga Mine Open Pit, Chingola, Zambia)-Mr. Lutton is to be commeneded on his analyses and presentation of such practical data which can be used for predicting a preliminary optimum slope angle in rock. It appears that he assumes all slopes analyzed to be straight. Although there are overriding factors which affect the general slope configuration, such as structural discontinuities, ground water, and other environmental factors such as weathering conditions, regional stress, etc.,8 the affects of plan geometry under certain conditions also can be of outstanding importance. In investigation of natural slopes, for example, the effects of plan geometry are not entirely appreciated and it is in this respect that discussion is given. Experience in southern Africa has shown that the overall geometry of surface openings in rock, particularly those with dimensions of the order of 1500 ft or less, i.e., where radii of curvature of the slopes are less than, say, 700± ft, must be considered in rational slope-stability analyses. That is, the slope angle is not only a function of slope height, strength of the mass, and geometry of structural discontinuities, but also is dependent upon the plan geometry of the local slopes and the plan shape of opening. Technically speaking, adequate analysis of the slope must be three-dimensional, the third dimension being that of overall plan configuration and the analysis must incorporate its subsequent effects. However, current theories of slope stability all deal with the slope as a two-dimensional problem, i.e., a slice of unit length of an infinitely long slope is considered for a condition of plane strain. In this the tacit assumption is made that the plan radii of the crest and toe of the slope are infinite and no attention is given to the plan geometry of the slope. Clearly this is not the condition encountered in practice, particularly in open pit mining where excavations, relatively speaking, can be small and where these radii of curvature accordingly can have important affects on the slope stability. This is illustrated by the analyses of Piteau and Jennings 9 of the natural slopes which had developed around pipes of four diamond mines in the semiarid Kimberley area of South Africa. Although these slopes consist of dolerite overlying shale, the values of the slope angles of all the pits were corrected for a height of slope of 320 ft assuming that no dolerite occurred. This brought the data onto a comparable basis. These data were analyzed statistically and a clear empirical relationship, as is shown [in Fig. 4], is seen to have formed between angle of slope and curvature of slope, i.e., the angles of slope are greatest where the radii of curvature are least. Also, it can be seen that the slope of each line is different, indicating that the plan shape of the open pits also are significant, the curve being steepest for the open pits which are more circular in shape in contrast to those which are more elongated. The effect of slope curvature on the average angle of slope for the two extreme radii of 200 ft and 1000 ft for all four open pits is 39.5° and 27.3°, respectively. Hence, the concave curvature effect represents an average increase in slope angle of 12.2° from the essentially straight slope. In quantitative terms in Mr. Lutton's Fig. 2, this represents displacing the curve for a 320-ft pit from the second curve from the bottom (i.e., shale in subtropical climate) to that of the third from the bottom (i.e., quartzite in temperate environment).

Jan 1, 1972