Search Documents

The kinetics of the hydrogen reduction of iron oxides in granular calcined bauxite were studied at 550-1,050°C in a shallow bed reactor. The iron oxides behaved as a dispersion of particulate iron oxide in a porous alumina matrix in which the iron oxide particles were reduced independently. The observed rates of reaction were found to be virtually independent of the bauxite grain size. At 800,°C and above, the reduction was multistage, Le.1. Fe203 +2Al203 (matrix) ?2FeAl204, and2. FeAl204? Fe0 +Al203.Reaction 1 was very rapid. Reaction 2 was much slower, the latter stages being controlled, at least in part, by phYSIcal changes of the Fe0 and a-Al203 produced in the reaction. Owing to the observed nature of the material, the reaction rate controlling steps could not be determined.

Jan 1, 1972

By Yues Bertube

Molybdenite and chalcopyrite are two often-associated minerals. In Quebec, the Gaspe Copper Company, a subsidiary of the Noranda group, currently operates a molybdenite flotation circuit to recover a one percent trace of this mineral in the chalcopyrite concentrate. The low levels of molybdeni 2 preclude the use of flotation to remove molybdenum directly from the ore while scavenging of chalcopyrite concentrate for molybdenite yields a concentrate of the latter of somewhat inadequate quality. Such a situation could possibly best be solved by hydrometallurgical means, if molybdenite could be leached selectively from the chalcopyrite concentrate. Work in the field of extractive metallurgy was initiated about 22 years ago in the laboratory of the department of mining and metallurgy at Laval University, Quebec. Following a literature search, two objectives were selected. The present talk will outline some of the results obtained to-date and it is hoped the ensuing discussion of the paper can raise questions of immediate assistance to us for the future. First, as an immediate objective of-practical use, the oxidation rates for molybdenite and chalcopyrite in alkaline media would be studied under conditions of possible industrial application. Secondly, the kinetics of mass transfer of gases in pressure reactor are to be studied. Solubility data for various gases in aqueous solutions have been gathered by a few investigators, to mention the work of Pray1, Wadsworth2, Pawlek3 and Gerlach. Scattering in experimental results and discrepancies between authors are ominously present. Kinetics of mass transfer have somewhat been more neglected. A systematic investigation by the school of Berlin has greatly helped in the design of impeller most suitable for gas dispersion, without much reference however to the solid dispersing ability of the various designs. Variables affecting rates of gas transfer to the solution have not been studied. Studies on the aqueous oxidation of sulfide minerals are much more numerous. While molybdenite has been relatively less studied, work has been carried in two areas namely in alkaline oxidation of MoS2 , work performed by Dresher2 and Wadsworth, and in the hypochlorite leach of molybdenite by Bhappu4 and co-workers, These two methods showed appreciable rates of leaching for molybdenite. In general, comparisons between rates of oxidation of this sulfide with that for chalcopyrite have not been made.

Jan 1, 1972

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972

By R. O. Dannenberg

The Bureau of Mines investigations described in this report were undertaken to devise a process to economically recover precious metals and copper from low-grade, complex electronic scrap generated in large quantities by military and civilian electronic operations. Leaching with various media is applicable to certain selected items of electronic scrap but cannot be practically applied to complex mixtures of scrap. A process comprising incineration, caustic leaching to remove aluminum, smelting with a siliceous slag, and electrolysis recovered 99.9-percent-pure copper metal and anode slimes assaying more than 7,000 ounces per ton of combined precious metals. Silver, gold, and copper recoveries were 93, 95, and 87 percent, respectively. Cost analysis indicated that an alternative process using direct smelting of the scrap to make assayable products for sale to a custom smelter would provide better overall financial returns.

Jan 1, 1972

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By Manuel Gomez

The mean and the standard deviation were used to describe general sulfur and ash populations as well as specific populations of these variables from one coal seam. Both the mean and the standard deviation were incorporated in the exploration process to determine the number of drill cores necessary for seam evaluation and to guide the sequential drilling plan. Probability regions were computed to establish a basis for predicting probable ranges of average sulfur and ash concentrations that may be expected upon continued or future drilling. A computerized plot program was utilized to interpolate sulfur and ash concentrations between grid points. The plot program, which is essentially a moving average technique, permits a rapid evaluation of sulfur, sulfur forms, and ash spatial distributions as a drilling program progresses sequentially. This information, in the form of contour plots, can be made available to both the mining engineer and the fuel technologist in advance of mining to outline reserves, to improve selective mining, and to anticipate preparation facilities.

Jan 1, 1972

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers' opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By A. V. Pegler, R. C. E. Bray

The purpose of this study is to determine the distribution of stresses in a particular portion of the ore body of an operating mine. DESCRIPTION OF GEOLOGY The ore body of this base metal mine is a lenticular mass of copper-zinc-iron sulfides, enclosed in a drag-folded quartz mica schist. The schistose host rock has steep dip which varies from north to south and an east-west strike. The drag-fold plunges eastward at about 35º, and this gives a rake of similar inclination to the bottom horizon of the ore zone. The core of massive sulfides is surrounded by an irregular envelope of disseminated sulfides in the schist, so that stope walls are comprised, in most cases, of strongly foliated schist. Adjoining the schist on the south is competent gneiss, while instrusive into the schist in a direction nearly parallel to the foliation is a series of discontinuous quartz diorite dikes, whose contacts with the schist often prove to be lines of weakness. Coarse to fine-grained pegmatites of irregular dimensions are a second type of intrusive associated with the ore body. These dikes generally strike north-east and dip westerly at about 65º. They therefore intersect the schist at an obtuse angle. The dikes are considered to be older than the massive

Jan 1, 1972

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By Martin P. O'Connell

"IT IS INDEED A PRIVILEGE to address a group representing a sector of the Canadian economy so important as is the mining sector. Important, not only today, but certainly of great importance for the future development of Canada, for employment, for our trade balance and indeed, when one looks at what we are calling increasingly an industrial strategy, for the future. Surely mining will have a very significant role to play in fulfilling that. It's of special interest to me, as the Minister of Labour - and I ought to confess at the very beginning that I am just two months into this function - of special interest for me to know that you are giving such attention to labour-management relations. I think it is timely that, from my point of view at least, you do this, because for the first time in twenty four years major revisions of the Canada Labour Code as it relates to industrial relations and disputes settlements are currently in the House of Commons going through their second reading, after an easier introduction and some changes which I would be very pleased to describe later this morning. It is very timely too, I think, that we should be looking at this area because public interest is certainly at a high level. It is not only at a high level but it expresses a good deal of irritation with the current status and procedures and results in collective bargaining and there is some urgent search for more sophisticated or modified procedures for settling differences in labour-management relations. The public wants different kinds of results. I think that is apparent to all of us. They want results in terms of justice and equity on both sides. And it means that a Minister of Labour and certainly governments who often are representing, or are the third party in discussions, have a very important and complex role to play in attempting to create a balance as these two parties come to contracts and come to agreements."

Jan 1, 1972

By James Yancik

The Howe Coal Co. is mining the Oklahoma Lower Hartshorne bed which ranges in seam thickness from 38 to 42 in. and pitches approximately 7° to the northeast. The raw feed to the cleaning plant averages about 20% ash and 1.10% sulfur, being reduced in the cleaning process to 4.8% ash and 0.9% sulfur with a free swelling index of 8 or 8%. This coal rivals the Pocohantas seam in chemistry and coking characteristics but has better fluidity than the Pocohantas seam coal. The coal is presently being prepared for the Japanese steel market in an 85-tph pilot plant designed and constructed by Roberts & Schaefer. The cleaning-plant flowsheet is discussed in detail.

Jan 1, 1972

By J. D. Dixon

Procedures are given for calculating stresses in underground tunnel supports which accounts both for the structural behavior of the support and that of the adjacent rock mass. Stresses in the support are caused by service loads and rock reactions. Service loads are due to rock pressures, hydrostatic and hydraulic pressures, selfweight of the support, or other utilitarian-type loads. Rock reactions, equal and opposite those in the support, are due to the deformational interaction that results as service loads deform the tunnel support against the adjacent rock mass. The procedures developed for solving this problem are an application of matrix structural analysis. The principles involved in this method allow for the consideration of the deformable characteristics of most tunnel support systems and an iterative solution procedure is applied to determine the areas of support-rock interaction. Numerical results of example problems are given.

Jan 1, 1972

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low and high backgrounds and low, intermediate, and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1972

By C. C. Merrill

Columbium, tantalum, titanium, and zirconium are present in solid waste products generated by the chlorination of rutile used for production of titanium tetrachloride (TiC14). The columbium and tantalum were separated from titanium and zirconium by liquid-liquid extraction techniques using a secondary amine. Salts of these elements are in a leach liquor produced by water leaching of mineral waste from the chlorination of rutile. This waste, produced at the rate of approximately 50,000 tons per year, is about 40 wt pct water soluble. Leach liquors, separated by filtration, were further separated into a solid fraction and a liquid fraction by pressure hydrolysis, The solid fraction containing Cb, Ta, Ti, and Zr was dissolved in HC1-HF and used as a feed solution. Columbium and tantalum were removed from the organic extractant with 1 [N] HC1. A miniature 10-stage reactor showed that the columbium and tantalum present in solution could be separated with a continuous flow.

Jan 1, 1972

By Joseph L. Condon

High-speed movies were taken of crater experiments in two-dimensional plates of Tennessee marble to study craters being formed primarily by stress-wave action. The contribution of gas action to the cratering process was minimized because the two-dimensional models did not contain the expanding gases from the explosive. Four burdens were studied for solid plates and one burden for a segmented plate. After cratering, the plates were reassembled for dye penetrant studies of fracturing. Flyrock velocities were calculated and related to the degree of fracturing, and compared with those from quarry shots. In general, the smallest burdens produced the highest flyrock velocities and the least amount of fracturing. Flyrock velocities compared favorably with initial flyrock velocities in quarry blasts, but did not show step accelerations due to gas effects as did the quarry blasts. The test with a segmented plate was used to simulate cratering in a jointed material and showed that stress-wave effects can be important for crater formation in jointed rocks.

Jan 1, 1972

By Leon Y. Sadler

Equations which predict the unsteady-state response of the continuous froth flotation cell to changes in operating conditions are necessary for the rational design of an automatic flotation cell control system. Unfortunately application of automatic control to froth flotation separation equipment has lagged behind application to other types of separation equipment (for example distillation columns, absorbers, liquid-liquid extractors, etc). This may be due partly to the unavailability of suitable mathematical models for predicting the dynamics of continuous mechanical froth flotation cell. This paper presents the results of a comparison of four dynamic flotation models (in transfer function form) using the same set of unsteady-state continuous flotation data. One of the transfer functions tested has been presented previously in the literature (1), another (2) has been accepted for publication, and two are given here for the first time. In addition, data are presented which confirm earlier findings that the mixing in the rotor-stator type cell is nearly perfect. The specific purposes of this paper are to: (1) provide the automatic control systems designer with several alternative dynamic mathematical models of the continuous mechanical froth flotation cell (2) give some idea of the relative a¬bility of each model to predict unsteady-state behavior by fitting each model to the same set of experimental stimulus-response flotation data and (3) provide more insight into the macro-mechanisms prevailing in the continuous mechanical flotation cell. The dynamic models which are presented and tested here all relate the time variation of the concentration of a given floatable mineral in the tailings to a time-dependent disturbance in the same floatable mineral concentration in the feed to the flotation cell.

Jan 1, 1972

By Hill McDonald

Sand and gravel deposits may be explored by many different methods. The methods used by The Standard Slag Company are primarily two in nature. One is using an auger which is limited in depth by various soil conditions. The other is a heavy wall dry sampler and a heavy wall wet sampler. The heavy wall dry sampler takes continuous uncontaminated samples up to seven inches in diameter. The heavy wall wet sampler takes continuous uncontaminated samples up to six inches in diameter. For us, the maximum depth of the heavy wall samplers has been two hundred fifty feet of which one hundred feet was above the water table and one hundred fifty feet was below the water table.

Jan 1, 1972

By H. Reginald Hardy, Y. P. Chugh, Robert Stefanko

Many materials including rocks, ice, metals and their alloys, wood, etc., emit transient vibrations in the audible and subaudible range when stressed. In rocks, this phenomenon is referred to as "microseismic activity, " "rock noise, " or " seismo-acoustical activity. " In metals this phenomenon is often termed "acoustic emission." Each individual microseismic disturbance is generally referred to as a "microseismim" or an "elastic shock." The terms "microseismic activity" and "microseismim" will be employed exclusively in this chapter. Microseismic activity has been observed in many rocks loaded experimentally in the laboratory.1 The form of a group of typical microseismims is shown in Fig. 1. Quantitatively, the microseismic activity in rock under stress is most commonly described by the number of microseismims observed per unit time. This is commonly known as the "noise rate." The noise rate in general increases with increasing stress level and rises sharply just prior to failure of the material.2 The origin of microseismims is not well understood, but it appears to be related to processes of deformation and failure which are accompanied by a sudden release of strain energy. In a polycrystalline material, microseismims may originate at the micro-level as a result of dislocations or at the macro-level by twinning, grain boundary movement, or initiation and propagation of fractures through and between the grains. It is assumed that the sudden release of stored elastic strain energy accompanying these processes generates a stress wave which travels from the point of origin, within the material, to a boundary where it is observed as a

Jan 1, 1972

By Don Stevens

The Denali Prospect (147° 08' 20" W, 63° 08' 50" N) is located on the south flank of the Alaska Range in the Clearwater Mountains in south central Alaska. (See Figure 1). The mineralization was discovered in 1963 and surface explora¬tion began the following summer. Surface trenching and diamond drilling were used to locate and sample the mineralized zones. In 1969, an adit totalling approximately 1400 feet was completed. In 1970, a -15% grade decline approximately 1800 feet long was completed. Further diamond drilling was done along with both underground programs. Although much work remains to be done to properly evaluate the prospect, results from all the work to date are quite encouraging. This paper will consider the geology of the prospect and the surrounding area, some- aspects of the geochemistry of the sulfides, and the origin of the sulfide deposits. This paper includes data from this writer's Ph. D. dissertation, "Geology and Geochemistry of the Denali Prospect, Clearwater Mountains Alaska" from the University of Alaska and subsequent work.

Jan 1, 1972

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972