Search Documents

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

The kinetic and practical aspects of the extraction of copper from copper-rich solutions by cementation on iron was investigated. Tests were made on the effect of stirring speed, cupric sulphate concentration, acid concentration, temperature, and ferric sulphate concentration on the reaction rate and excess iron consumption.Most kinetic investigations were conducted under a nitrogen atmosphere to prevent any oxidation of the iron or copper metals. The stirring mechanism for all tests incorporated the use of a rotating impeller above a static disc in the solution. The activation energy for cementation on the steel disc at high stirring speed was 8·6 kcal/mole, indicating a predominant chemical control.Increasing the pH first decreased, then above pH 3, increased the reaction rate. Additions of sodium sulphate also significantly increased the reaction rate.The use of high temperature and high pH under an inert atmosphere has been suggested for increasing the reaction rate and producing a high purity sponge copper product.

Jan 1, 1972

By Kandalla Ravindranath, C. C. Patel

Studies of the adsorption of dialkyldithiocarbamates at the surfaces of galena and sphalerite have shown that characteristic contact angles are obtained at galena surfaces in the 7-10 pH range, whereas lower angles are obtained at unactivated sphalerite surfaces even at pH 71 Further, the angles at sphalerite surfaces progressively decrease with increase in pH. However, when sphalerite is activated with cupric sulfate, characteristic contact angles are obtained at pH 7 and beyond. This shows that galena and sphalerite can be selectively floated with dithiocarbamate collectors at pH 7 and beyond. Experimental Materials Ore: The lead-zinc ore for the present study was obtained through the courtesy of the Geological Survey of India from Dariba, Udaipur, Rajasthan, India. The average ore analyzed 15.5% lead, 11.6% zinc, 6.7% iron, 15.6% sulfur and 36.6% acid insolubles. The ore was crushed in a Denver laboratory rod mill and sieved in a Denver automatic sieve shaker to obtain a -200- to +250-mesh (Tyler standard) fraction. This particular size was chosen because it was conducive to good liberation of sulfide minerals, both from one another and from gangue minerals. Collectors: Dimethyl, diethyl, diisopropyl and diisobutyl dithiocarbamates were prepared and purified by the methods described by Klopping and Van der Kerk.2 A freshly prepared 0.03% dithiocarbamate solution in distilled water was used for flotation studies. Frother: A 0.03% solution of pine oil in ethyl alcohol was employed. Activator: 7.3 g of cupric sulfate pentahydrate were dissolved in 1 1 of water and used for the activation of sphalerite. Depressant: 16.0 g of zinc sulfate heptahydrate were dissolved in 1 1 of water and used for the depression of sphalerite.

Jan 1, 1972

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By Leonard Sugin

Recent changes in the field of ore and bulk commodity handling has forced a reevaluation of previously conceived notions. When vessels were small, and sources of raw material were reasonably close to areas of need, the role of the shipping terminal was of secondary importance. Now terminals must be built to take advantage of the economic benefits of the supercarriers. The shipping rates of the 80's will not be determined by the 60,000 DWT or even 150,000 ton capacity bulk carrier, but rather by the supercarriers in the 250,000 DWT class or larger. When the Suez Canal was closed, the shipping industry took a hard look at the economics of the large bulk carrier. Naval architects overcame the problems and successfully designed large supertankers, which today are plying the seas in excess of 350,000 DWT. Orders have been placed for tankers of 480,000 DWT. The shippers of dry bulk materials are now coming to similar conclusions about the economics of supercarriers. As of today, over 40 orders have been placed for vessels in the 250,000 DWT class, representing an investment of over 11/2 billion dollars, and many more are being considered. These vessels are being designed as combination ore/oil (0/0) or ore/bulk/oil (OBO's) carriers. The oil industry has seen the need for terminals which can accommodate these supertankers. The dry bulk shippers, and particularly ore shippers, must now act.

Jan 1, 1972

Contract No. H0110929 was awarded by the U.S. Bureau of Mines in February, 1971, to DeTer Company, Incorporated, of Mountain Lakes, N. J. The contract provided for the modification of the contractor's Model 5000 Pressure Foam Generator to fit it for the suppression of coal dust in mines, a detailed testing program in a working coal mine, and for additional modifications and testing for the suppression of fires in coal mines. The contractual program was completed in April, 1972. The results of the dust suppression tests showed conclusively that the modified DeTer equipment effectively reduced the level of respirable dust in a working coal mine well below the present and future acceptable levels set by the Mine Health and Safety Act of 1969. The fire tests, carried out in a simulated mine entryway erected on the surface, demonstrated the ability of the DeTer equipment in suppressing fires of varying degrees of severity within an acceptably short time.

Jan 1, 1972

By K. J. Rosengren

INTRODUCTION Mount Isa Mines Limited operates a major mining complex at Mount Isa in northwest Queensland, Australia. The location is arid and remote, some 600 miles distant from the nearest port of Townsville on the eastern coast (Fig. I). Current mine production is 6 million long tons per annum comprising 3.8 million tons of copper ore and 2.2 million tons of silver-lead-zinc ore. Copper ore production is scheduled to increase to 5.8 million long tons per annum by 1973 and a new silver-lead-zinc mine is being developed at Hilton, 13 miles north of Mount Isa. The Mount Isa and Hilton orebodies occur in a single stratigraphic member, termed the Urquhart Shale. This shale is conformable with several other sedimentary formations striking north-south and dipping approximately 65º west. The silver-lead-zinc orebodies occur in bands conformable with the shale bedding and tend to be of tabular shape, varying in width from a few feet to nearly 200 ft. The copper orebodies occur in breccia bodies, locally known as "silica-dolomite", within the Urquhart Shale and tend to be more irregular and massive with widths up to several hundred feet. The detailed geology is described by Bennett (1 2). At present, production comes almost entirely from underground operations with only about 25,000 tons per year of carbonate ore from open pit operations. The mining method used in the copper orebodies is sublevel open stoping with pillar recovery by pillar blast before stope filling or by sublevel caving after stope filling. A large primary sublevel caving operation was also carried out until recently in one of the orebodies. The wider lead orebodies are mined by sublevel open stoping, with or without pillar recovery, while cut and fill stoping is used in the narrower orebodies. Details of the mining methods are given by Davies (3). The company's interest in open pit mining stems from a large open pit which was mined out in 1965 and a further large open pit planned for future production. In addition, the company is currently evaluating several large ore deposits in Australia and New Guinea. All of these orebodies would be mined by open pit methods and rock mechanics studies of slope stability are now a standard feature of all open pit evaluations.

Jan 1, 1972

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972

By James R. Russell

Rock bolts are commonly used to support and stabilize the rock around excavated openings. The assumption is made that the less competent rock near the surface can be supported by bolting it to more competent rock away from the surface. Naturally, a rock bolt can be no more effective than its anchoring mechanism which induces a stress field into the surrounding rock. Details of various types of bolts have been described e1sewhere.l The purpose of the present investigation is to study the stress distribution around an expansion-type rock bolt anchor, using the theory of elasticity. The elastic stress distribution provides some insight into the behavior of rock bolt anchors which may eventually lead to improved designs. Very little information is available on the induced stress field which is rather complex; consequently, photoelastic techniques have been used to obtain a qualitative picture of the stress ditribution.2 The present work provides quantitative information on the stress field induced by an idealized distribution of surface tractions, provided that the assumptions of the linear theory of elasticity are approximately satisfied. FORMULATION OF THE PROBLEM Consider an elastic region which extends to infinity and contains a circular cylindrical hole as shown in Fig. 1. The hole is assumed to be the bolt hole and the surface tractions shown are assumed to be caused by an idealized rock bolt anchor. The relationship between the idealized

Jan 1, 1972

By A. W. Deurbrouck

This report presents the results of a washability study of 322 coal mine samples showing the sulfur forms and distribution in the coals. The samples were collected from mines which were principally utility coal producers. Generally, the data show the total sulfur content of the coals evaluated could be significantly reduced by some combination of stage crushing and specific gravity separation. However, few coals could be upgraded to a final product containing 1 percent or less total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds.

Jan 1, 1972

By P. B. Knuckey, D. Littleford

The Kalengwa mine, situated in a remote area of Zambia in Central Africa, has presented some unique problems to the planners engaged in developing the deposit. This small, high grade copper deposit contains some 1,688,000 tons of ore at a grade of 9.3% contained copper. Of this 362,000 tons is classified as high grade ore at 27.2% Cu, the coarse fraction of which can be fed directly to converters; 733,000 is classed as intermediate grade ore averaging 6.3% Cu, and 593,000 tons classed as low grade ore containing 2.1% Cu. The geology of the deposit and the establishment of the mining operation is fully described. A concentrator is being built at Kalengwa to treat the high grade fine product, intermediate, and low grade ore, whilst the coarse high grade ore will be trucked to the Copperbelt smelters for direct smelting. Details of metallurgical processing are given. The decision to truck the coarse high grade ore to the smelters on the Copperbelt necessitated the construction of a new 200-mile road, the setting up of a fleet of heavy ore transport trucks and associated equipment. The remoteness of the area from established communication facilities on the Copperbelt necessitated the provision of radio communications between Kalengwa and the head office at Kalulushi, and the establishment of a regular mine air service. The paper also describes the training of an unsophisticated local population in the operation of heavy plant and machinery, the establishment of the township, and the provision of health services.

Jan 1, 1972

Mackenzie (1968, p. 167) inferred that amphibolitelayers grade into and may be correlated with footwall Potosi gneiss where it is thin under the thickest development of the "lead lode" in the New Broken Hill Consolidated mine, Broken Hill. This gradation from amphibolite to Potosi gneiss is tacitly assumed in many of the constructed crosssections of the southern end of the orebody, where amphibolite and Potosi gneiss, defined in hand specimen, are correlated in adjacent drill holes. The basis for such correlations is the observation that some amphibolites in drill core lighten in colour from black to grey along the core and grade into an unlayered rock containing conspicuous pink garnets, which resembles Potosi gneiss (for descriptions of Potosi gneiss see Andrews, 1922; Gustafson, BurreIl and Garretty, 1950; Carruthers and Pratten, 1961;\Ternon, 1969).Average chemical compositions of "footwall" Potosi gneiss and "upper" amphibolite (Hawkins...

Jan 1, 1972

In recent years, with the advent of new steelmaking procedures, the emphasis has turned away from conventional teeming and has been directed toward continuous casting. This paper points out the fact that there are still new methods being considered to decrease the problems and costs associated with conventional teeming. Although Inland has had no experience with the repair of mold lugs, we do find some problem with damaged ears associated with mechanically capped steel. When pouring bottle tops, any crane movement or leak from the pouring nozzle may result in steel over the top of the mold which, in turn, may result in the shearing of the mold lugs during stripping. Recent back pouring practices increase the chances of this occurring. At Inland's steelmaking shops, we have tried to combat this problem by various methods such as burning the steel from around the top of the mold at the pouring stand with oxy-gas torches. Last year, No. 4 BOF began a conversion from round to elliptically shaped bottle top caps. This change has greatly reduced the chance of splashing due to crane swing by increasing the dimension in the direction on normal swing. The answer to this particular problem is, however, tighter control of pouring performance. We are presently engaged in a process of re-education of personnel and experimentation with different materials and designs of nozzles, heads, and sleeves to help us achieve our goal.

Jan 1, 1972

By W. D. Mulholland

"I ASSUME that any effort on my part to deal with the question of the importance of the mining industry is going to be largely an exercise in preaching to the converted, but there are one or two aspects that I'd like to particularly mention.The first is that, in terms of almost all factors, the mining industry is a very important industry in Canada. It is important in terms of employment in relation to the gross national product of Canada and it is particularly important in the international trade of Canada. So far from being insignificant domestically, it is also an extremely important factor in the international picture. That's an important point to bear in mind, because as we talk about all the other matters we never can lose sight of the fact that mining management always has to be conscious of its international competitive position. It is something that one forgets at one's peril, and to a somewhat greater extent than is true of many other industries, those managements have to compete in an international context for their markets, to some extent for their people for specialized skills and of course for finance. In the evolution of domestic policies it is a very, very perilous step to take to impair that competitive ability of the domestic mining industry."

Jan 1, 1972

By B. I. Ferber

Toxic and explosive atmospheres are discussed, along with some of the instruments commercially available for their detection. No attempt has been made to evaluate the accuracy of anyone device. This circular has been prepared primarily to aid mine inspectors in selecting suitable instruments for underground gas detection.

Jan 1, 1972

Developments in furnace construction and design have been very rapid in recent years. Larger furnaces operating at high top pressures with much improved burdens are giving extremely high production rates. Modern scientific techniques and the use of computer control are contributing to these Rates.

Jan 1, 1972