Search Documents

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By W. C. Whittaker

"This paper gives a brief resume of the changes in the market picture for Western coal since 1948. It then analyzes present markets and recent developments in Western Canada, the western United States and Japan, and forecasts future markets in these areas to 1975.INTRODUCTIONCOAL HAS BEEN MUCH IN THE NEWS OF LATE, both in the United States and in Canada. In the United States, this is because of the booming condition of the industry and because of the purchase of control of a number of America's largest coal producers by the integrated oil and metal producing companies seeking additional fossil fuel reserves and diversification. In this regard, it is interesting to note that ownership of America's largest strip coal producer was recently acquired by one of the world's largest copper mining companies. In Canada, the conclusion of several large-scale, long-term contracts for the sale of coal to the Japan Steel Group and the projected use of Canadian coal in steel mills in the western United States has focused much attention on the coal industry."

Jan 1, 1968

By Y. C. Liu, G. A. Alers, S. S. Choi

In searching for an explanation for the obvious difference between the copper and the brass type of rolling texture, it is common practice to look for correlations with other properties. For example, there are obvious differences between copper and brass in the critical resolved shear stress, the extent of easy glide or stage I, and the amount of "overshooting)) during single-crystal deformation.' Also, the slip lines in copper are fine and wavy while those in brass are more coarse and better described as slip bands.' Since neutron irradiation is known to make these properties in copper change in such a way as to resemble brass,2'3 an excellent test for these possible correlations is to see whether neutron irradiation produces a corresponding change in the texture, i.e., whether irradiated copper develops a brass-type rolling texture. The experiment would also answer the more important question of whether or not lattice defects like those introduced by neutron irradiation have any effect on the development of rolling textures in fcc metals. Experimental studies using conventional X-ray pole figure techniques are inconvenient because the X-ray detection system must be modified to discriminate against the radioactivity which is induced in the specimen by the necessarily long exposure to neutrons. Nevertheless, some texture determinations have been

Jan 1, 1968

By A. E. Jenkins, A. Jostsons

Isothermal sections of the Ti-0-H phase diagvam at 600°, 700°, and 800°C have been constructed from equilibrium hydrogen pressure measurements over a range of Ti-0-H alloys containing up to 34 at. pct 0. Oxygen reduces the hydrogen solubility at fixed hydrogen pressure but increases the terminal solubility in the a solid solutions at the a/(a + P) phase boundary. Metal-lographic studies of alloys annealed below the eutectoid temperature show that oxygen also increases the ter-ninal solubility of hydrogen in the a solid solution in equilibrium with the hydride phase. The effect of oxygen on hydrogen solubility is discussed in terms of the electronic and geometric structure of interstitial solid solutions. THE isothermal solubility of hydrogen in a Ti-0 alloys at 800°C has been measured by Hepworth and ~chuhmann' who subsequently used ternary Gibbs-Duhem integrations to calculate oxygen activities in binary Ti-0 alloys. The present study aims to extend Hepworth and Schuhmann's measurements to alloys richer in oxygen and to a range of temperatures. This paper presents the results of hydrogen equilibrium pressure/concentration measurements in Ti-0 alloys as well as observations on the effect of oxygen on the terminal solubility of hydrogen in a titanium. The thermodynamic properties of binary Ti-0 alloys, derived from these measurements, will be published separately.' EXPERIMENTAL METHODS Specimen Preparation. Ti-0 alloys were prepared from iodide-refined titanium and titanium dioxide obtained by hydrolysis of redistilled titanium tetrachlo- ride. Specimens containing up to 16 at. pct 0 were prepared by electromagnetic levitation3 whereas a conventional tungsten arc furnace with a water-cooled copper hearth was used to melt oxygen-rich alloys. The specimen homogeneity was indicated by the constancy of lattice parameters of samples from various parts of the ingot as well as by the sharpness of the reflections on X-ray powder patterns. Oxygen-rich specimens in the composition range (20 to 34 at. pct), where ordering has been ~bserved,~ were annealed for 300 hr at 600°C prior to use in hydrogen solubility measurements. Apparatus. The hydrogen pressure/concentration measurements were made with a modified Sieverts apparatus shown diagrammatically in Fig. 1. Specimens were placed in a clear silica tube and impurity pickup by direct reaction with silica was prevented by lining the heated end of the silica tube with thin molybdenum sheet. A double silica tube was required to eliminate loss of hydrogen by diffusion through silica at high temperatures and high hydrogen pressures, the space between the tubes being maintained at a hydrogen pressure equal to that above the specimen. Hydrogen was purified by diffusion through a Ag-Pd tube.= Hydrogen pressures were measured with a mercury McLeod gage in the range 0.001 to 4 Torr

Jan 1, 1968

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By F. W. McQuiston, L. J. Bechaud

3.2-1. Introduction. Much has appeared in the technical literature on theory of sampling (18, 37), weight of sample required in relation to particle size (28), probability of error in sampling (3), and statistical analysis of sample data (20). Each industry, whether it be copper, iron ore, or coal, has its own standards and methods. All of the rather extensive theoretical treatments appearing in published literature on sampling apply to material already on hand such as coal, iron ore, or copper concentrates in rail cars, or in moving streams such as on conveyor belts. The attempt usually is to apply statistical techniques in order to improve reliability and precision in sampling, and to reduce differences between the analyses of seller and buyer. In contrast to this type of sampling, very little has appeared in the literature on sampling a virgin deposit from the metallurgical point of view. Perhaps it would he more descriptive to designate this point of view as "Gm-metallurgical," since geology is inextricably interwoven with metallurgy in gaining an understanding of the complexities of a deposit, eventually leading to a definition of mineable reserves, with the development of a flowsheet and engineering criteria for the planning of a successful and profitable operation. The degree of cooperation between these two departments often determines whether the processing plant is a success at the inception of operations, or whether expensive changes and modifications must he made, with the plant finally reaching rated capacity at some later date. The first concern of the metallurgical department should be to establish proper accreditation of the samples which will be used in any ore-testing campaign. It should he made mandatory, as part of operating management policy, for the responsible metallurgist to he aware of the significance of the samples and to become intimately knowledgeable in all aspects of metallurgical behavior and response to treatment of all varieties of ore in the deposit under consideration.

Jan 1, 1968

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

This publication is designed to be helpful in promoting health and safety in tunneling and related operations. The format has been selected and arranged to provide a condensed guide for safety personnel, inspection and investigative agencies, design and project engineers, and others responsible for the health and safety of workmen. All the precautionary measures recommended are based on actual conditions observed, from investigations of fatal or serious accidents, and from research conducted to find ways and means of alleviating hazards and unhealthful conditions. Many of the recommended rules are included in State laws and in the general safety requirements of the construction industry. Explanatory, descriptive, and qualifying information has been largely omitted in this publication to keep basic data in more useful and compact form. Included in the appendixes are special precautions for gassy (methane atmospheres) tunnels and tunnels where petroleum products are encountered.

Jan 1, 1968

By M. J. Salkind

In discussing the possible contribution of plastic deformation to neck growth during sintering, Wilson and Shewmon State that Lenel, Ansell, Salkind, and Early34, 35 concluded that dislocation flow is the rate-controlling process in sintering under zero external load. The experiments cited34, 35 were done with applied external loads, and the conclusions were that the same kinetics could be controlling sintering due to the force of gravity with no additional applied load. The effect of gravity on sintering behavior was previously cited.34, 31 In addition, Wilson and Shewmon argue that the conclusions of Refs. 34 and 35 are doubtful because the strain rate is proportional to stress for plastic flow. This assumption is true only for certain kinds of plastic flow such as Nabarro-Herring Microcree38 As Early, Lenel, and Ansell point out3' plastic flow, based upon dislocation movement, can exhibit strain rates which exhibit a power law relationship to the applied stress.39, 40 Wilson and Shewmon also doubt the results of Refs. 34 and 35 because the stresses in the necks are too small for x/a > 0.1. This is true, and the experiments described in Refs. 34 and 35 were done for small values of %/a. The conclusion was that plastic flow by dislocation movement was important during the early stages of sintering when x/a is small.

Jan 1, 1968

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968

By J. G. Tilton

While most of the Pittsburgh coal horizon is dependably regular, there are areas where it is dis-turbed by sandstone cutouts which can seriously hamper mining operations. Because these channel sandstones often cut out the coal abruptly, they are difficult to detect by core drilling; and mine operators, for want of a better way to discover them, have largely trusted to luck to avoid them. This paper, based on a study the author is presently conducting, is an attempt to point out some sources of information and signposts which might aid the operator in determining the presence of a cutout before he begins to mine. The presence of sandstone cutouts in the Pittsburgh coal has been known for many years. Some of these irregularities were observed at outcrops and others were discovered by drilling, but the majority were and are found during mining operations. These sandstone cutouts are commonly called "faults" and have been a bane to mining companies wherever they have been encountered. Profiles of some typical deposits appear in Fig. 1. The cutouts disrupt the normal system of mining, replace valuable coal reserves, create ventilation problems by emitting large quantities of gas and sometimes oil, limit the number of entries that can be economically driven, affect the quality of the coal, disrupt the normal structure of the coal, and create roof control problems. It might be expected that such severe disturbances in the structural regularity of the coal would instigate determined and extensive searches for possible cutouts prior to mining operations, but this apparently has not been so except in isolated cases. Two reasons may be cited to explain this lack of exploratory work. The first and probably the strongest reason is the over-all regularity of the Pittsburgh coal. No coal seam in the country exhibits the horizontal continuity and relative regularity of the Pittsburgh coal. It lies in an almost unbroken sheet across southwestern Pennsylvania, eastern Ohio and northern West Virginia, and has been recognized as far east as the Potomac Basin of western Maryland. Over 5729 square miles are underlain by this coal, of which 2077 square miles are in Pennsylvania, 2214 square miles in West Virginia, 1410 square miles in Ohio, and 28 square miles in Maryland. The area covered by this study is outlined by the map in Fig. 2. Over most of this territory the coal has the following characteristic structure as illustrated in Fig. 3: roof coal, draw slate, breast coal, parting, bearing in coal, parting, brick coal, parting, and bottom coal. With such regularity of thickness and structure, mines were opened and laid out with confidence that the coal would be present. Extensive drill testing was considered unwarranted and it was also quite expensive because the coal dipped to the west away from the Monongahela River. Consequently, drill holes were widely spaced and rarely encountered ad-

Jan 1, 1968

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By D. T. Peters

To better understand the Co-Mo interaction in maraging steels, the precipitate reversion behavior of two alloys closely related to the 18 Ni-250 grade has been studied. The reversion experiment is carried out by aging at a low temperature, T1 (preaging temperature), for some period of time and then aging at a higher temperature, T2, called the reversion tetnperature. Aging and reversion tmzperatures used were in the range 679 to 1050°F. Reversion is marked by an increase in resistivity and a decrease in hardness. It teas found that some reversion took place at all cornbinations of T1 and T2 but that pronounced rei3ersion resulfed for an Fe-18 pct Ni-5 pct Mo-8 pcl Co alloy exposed to preagz&apos;ng&apos; temperatures at or below 850°F. A similar alloy not containing cobalt exhibited no such discontinuity in reversion behazior with TI. The results are interpreted in terms of two types of molybdenum-rich precipitates, one nucleated at dislocations and the other in the matrix. The increased supersaturation resulting from the presence oj- cobalt evidently provides sufficient energy to nucleate the matrix phase. Anotnalies in the temperature dependence of the resistivity decrease and peak hurdness in the Fe-18 pct Ni-5 pct Mo-8 pct Co alloy as a junction of aging temperature noted in an earlier study are explained on this basis. SEVERAL investigatorsl-9 have studied the details of the precipitation-hardening reaction of the maraging steels. The great majority of conclusions have been drawn from transmission electron microscopy. Although much has been learned by this method, alternate techniques which will give information earlier in the aging process are needed for a more complete understanding of the series of precipitation steps probably involved in the aging reaction. Peters and cupp&apos;&apos; have recently shown, by measurements of the kinetics of precipitation, that an 18 pct Ni-Co-Mo maraging steel shows a distinct change in precipitation behavior at aging temperatures below 850°F. The results were interpreted in terms of the existence of two types of precipitates at low aging temperatures. Only one precipitate type is present at higher aging temperatures. The low-temperature precipitate was found to be a particularly effective strengthener. No evidence for the additional low-temperature precipitate was found in the 18 pct Ni-5 pct Mo ternary alloy. The object of this investigation was to study further the characteristics of the two types of precipitates and the interaction between cobalt and molybdenum characterizing this system. Some preliminary experiments indicated a difference in reversion behavior in specimens aged above and below 850°F. This suggested that knowledge of the reversion behavior might shed some light on these two questions. Hardy and Heal11 have defined reversion as the loss of hardness, electrical conductivity, or other properties caused by heating for a very short time at temperatures above the aging temperature. The precipitate reversion referred to in this paper is entirely distinct from "austenite reversion" often referred to in maraging steel literature. This latter phenomenon could more accurately be called the diffusion-controlled formation of austenite. Much has been written about reversion in several of the aluminum-base binary and ternary alloys.&apos;2-16 Two explanations for reversion have been advanced. Based on the classical nucleation theory of Volmer-Weber-Becker-Doring,17 Konobeevski18 suggested that reversion was due to the size of the precipitate particles

Jan 1, 1968

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By W. E. Bearce

The recent concern for the recovery of even the finest fractions of coal preparation plant feeds has created needs for new equipment. Thermal dryers currently available have difficulty reducing the filter cake moisture on down to the desired point. This difficulty involves 1) the physical problem of handling this wet, sticky material and making each particle accessible to the hot gases, and 2) removing the extremely fine dried particles from the cooled gases. The dryer described in this paper handles the first of these problems, and eliminates the second by the substitution of steel balls for air as the heat transfer medium. As a general statement, the cost of preparing coal for market is inversely proportional to the size of the lumps or particles. In the not too distant past the finer sizes were discarded as being uneconomical to treat and this practice might be still continuing if it were not for the insistence of the public that this material be kept out of our streams. This being the only cost-free outlet, the disposal of fine refuse became a significant item of expense in every preparation plant. When this happened it was only reasonable to look to the recovery of the values in this material, not only to defray this expense, but to reduce the tonnage which had to be wasted. There seemed to be no device available suited to reducing the moisture in this material to what the market requires. All of the fine coal dryers commonly employed make use of air to bring the heat of combustion into contact with the coal particles. Any device employing air as a heat transfer medium, has the following two strikes against it in attempting to handle 28 mesh by 0 filter cake: 1) It is practically impossible to bring the hot air into intimate contact with the enormous number of fine particles stuck together in the cake. 2) Even if this can be effected, it is impossible to remove the dried coal from the air. A wet scrubber must be employed, the discharge of which must go back to the filter and dryer as a circulating load of the most objectionable sort, being the extreme fines. Various compromises have been used to cope with the problem of drying this relatively small tonnage of high moisture coal. Often some of the dried coal is mixed back with the feed to the dryer in an attempt to make the mixture more handleable and more available to contact with the hot air than the filter cake alone would be. This may help to some extent with the first problem but it does nothing about the second and a dryer operated in this way has to be oversized. Sometimes the filter cake is mixed with a coarser fraction for the same reason. Here again, while this may make a mixture (the particles of which are more readily brought into contact with the hot air), the problem of getting the fine coal out of the air remains and a larger percentage of the total coal to be dried is handled by the most expensive means. Mechanical dewatering has accounted for more and more of total coal drying lately and in many cases would satisfactorily handle the whole load, down to 28 mesh, if there were a means available for doing a good job on the —28 mesh by itself. The dryer which is the subject of this paper was designed expressly for doing this job — drying fine material by itself regardless of how wet it may be to start with, how fine it may be, or how gummy and sticky these properties in combination may make it. The essential features are depicted in Fig. 1. A rotating cylinder is supported on a frame in such a way that one end may be raised or lowered by hy-

Jan 1, 1968

By J. R. Johanson

In recent years the procedures for functionally designing bulk storage bins and hoppers have evolved from qualitative guess and try methods to a quantative method based on theory and tests of the bulk solid to be stored. This quantative method, developed and implemented by Dr.&apos;s A. W. Jenike and J. R. Johanson as with any new design, must prove its effectiveness and validity in the actual operation of the finished equipment. How accurate are the theoretical predictions? Is it possible to extrapolate from bench size tests on a small ample of the bulk solid to the full scale bin design? Can the theoretical designs be economically translated into working hardware? In this paper the answers to these questions are discussed in light of actual bin operations.

Jan 1, 1968

By W. E. Halle, G. J. S. Govett

"The Institute of Applied Geology, Manila, Philippines, is jointly sponsored by the University of the Philippines, the Philippines Bureau of Mines and the United Nations Development Programme (Special Fund). It provides, in its fourth year of operation, an interesting example of international cooperation in mineral development. Objectives include: (1) the training of mining engineers in modern techniques of mineral exploration; (2) assisting government and industry in discovering new ore deposits; and (3) providing the basis for the establishment of an economically oriented graduate school of geology at the University, the first of its kind in the country. Training of engineers requires roughly one full year, which is divided between academic study and actual field practice. Lecture and laboratory instruction include courses at university level designed specifically to up-grade those aspects of the geological sciences that are required by mining engineers now qualifying as mineral exploration engineers-economic geology, applied geochemistry, geo-physical exploration, petrology and structural geology. The field training involves direct participation in actual mineral exploration projects arranged with the co-operation of the Bureau of Mines and private interests engaged in mineral development and production. The system works well in practice, and the Institute staff and trainees were responsible for outlining new evidence of economic mineralization. It is also apparent from the application of the exploration methods available to the project -geological mapping, air photo interpretation, magnetic, electric, electromagnetic, self potential and gravity surveying as well as geochemical prospecting -that, under the humid, tropical, mountainous conditions in which the practical program was conducted, air-supported geochemical prospecting with attendant reconnaissance geological mapping affords the most economical and effective approach to mineral exploration for at least some of the deposits characteristic of the region."

Jan 1, 1968

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex3 X-ray instrument for the measurement of the ash content of washed bituminous coal products. The results obtained for selected products from six preparation plants in the Appalachian region and one preparation plant in the mid-western region are described. Emphasis of the study was placed on low-ash bituminous coal products suitable for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by ash determination using the Cendrex for all products tested.

Jan 1, 1968