Search Documents

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

By R. C. Hall

We are pleased to confirm some of the mechanical data presented by Dr. Detert on the 18 pct Ni marag-ing steel.15 Bar 3 in. in diam and containing 0.02 wt pct C, 18.5 Ni, 8.9 Co, 5.1 MO, 0.55 Ti, 0.05 Al, and balance iron has been examined in our laboratory. Cylinders 0.5 in. high and 0.4 to 0.5 in. in diam were cold-compressed from 3 to 40 pct reduction in height. Table VI shows some typical data; deformation in-

Jan 1, 1968

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal' Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By J. F. Held

In a study of the influence of cold rolling on mechani cal properties of steel, it was found that the specific rolling procedure influenced crystallographic orientation. Properties developed by several rolling modes were determined and related to crystallographic orientation. Sanzples were cold-rolled various amounts on a laboratory mill. When palm oil was used as a lubricant, the crystallographic orientation was homogeneous throughout the thickness of the samples. Other samples were rolled without lubrication. Variations in intensity of the recrystallization texture components persisted throughout more than 50 pct of the volume of these samples. When the average plastic strain ratio, which is dependent upon crystallogvaphic orientation, was plotted as a function of percent reduction, a maximum was found at 40 pct in the samples which contained the observed texture variation. No maximum was found for the samples with the homogeneous texture distribution. Other mechanical properties, such as tensile strength and yield strength, were not influenced by the variation in crystallopaphic orientation. MECHANICAL properties of steel sheets depend, in general, upon the structural properties of the steel. For example, the Petch equation describes the relationship between yield strength and grain size. Other properties, such as hardness, vary with chemical composition. The plastic strain ratio, or R value, has been found to be dependent upon crystallographic orientation . In the course of investigating the effect of cold rolling on mechanical properties, it was found that a previously reported relationship between percent cold reduction and R value was not always observed. Published data had shown that the optimum cold reduction for best R values is 70 pct for aluminum killed steel.' However, by altering the rolling conditions, the optimum reduction can be shifted to much lower values, or it can be moved to very high values. This paper describes the rolling conditions that lead to shifting of the optimum cold reduction. The effect of rolling conditions on the various structure parameters and the resulting mechanical properties are evaluated. EXPERIMENTAL PROCEDURE Samples of three low-carbon aluminum killed steels were cold-rolled various amounts on a 9-in.-diam 2-high laboratory mill. Hot-mill thermal practice and steel chemistries are listed in Table I. Steel A was rolled with palm oil lubrication and heavy reductions on each pass; i.e., a total reduction of 75 pct was ac- complished with a maximum of five passes. Steel B was rolled without lubrication, and light reductions were given on each pass. After approximately 75 pct reduction, it was necessary to use a small amount of light oil to achieve any additional reduction in thickness. Following cold reduction, the samples were box-annealed at 1300°F for 10 hr. The heating rate between 800" and 1300°F was 50°F per hr, and the cooling rate following the soak period was 50°F per hr. Tensile specimens were machined from the annealed material and these were used to measure yield strength, tensile strength, and the plastic strain ratio (R value). Recrystallization textures were determined by an inverse pole figure technique.*'3 Integrated intensities of the (110), (002), (112), and (222) reflections were recorded for those planes lying parallel to the sheet surface. Examinations were made on both surfaces of each sample, and also at various levels beneath each surface to approximately 0.010 in. depth by etching techniques. RESULTS R Values. The R values obtained in steels A and B are shown as a function of percent cold reduction in Fig. 1. No optimum cold reduction was observed in steel A, rolled with palm oil lubrication. It is likely, however, that an optimum reduction would have occurred had higher reductions than 88 pct been employed. The optimum reduction in steel B occurred at 40 pct. The behavior in both of these steels is quite

Jan 1, 1968

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

The 64th Regular Meeting of the Rocky Mountain Coal Mining Institute convened at Jackson Lake Lodge, Grand Teton National Park, Wyoming, and was in session at 10:00 a.m. The meeting was called to order by Past President .Tames Westfield. He introduced Mr. Raymond C. Lillie, President of Grand Teton Lodge Company, who welcomed the members to Jackson Lake Lodge. Mr. Lillie stated he had been with the organization since the Lodge was built. They had a snowstorm the day before our meeting so stated it was perfect weather for coal miners. Mr. Westfield introduced President Joe T. Taylor, Superintendent, York Canyon Mine, Kaiser Steel Corporation, Raton, New Mexico. Mr. Taylor was born in Miami, Florida. Attended the Colorado School of Mines and graduated in 1952. He was associated with Sunnyside Operations of Kaiser Steel Corporation in Utah until 1962. Was then transferred to the Koehler Mine in Raton, New Mexico, as Superintendent, and had charge of opening the new mine, York Canyon, and at the present time is in charge of Kaiser operations there.

Jan 1, 1968

By W. Henry Weimer

A successful surface coal operation requires the combined efforts of engineering and operating personnel. In the planning for a mine, machines should be selected to do the best work in getting the coal uncovered, loaded, and transported to the preparation plant. The best system and extent of cleaning will be determined by the market. After the fundamentals of operation have been established, the operating personnel should see they are carried out. There is no simple solution to some of the every day problems facing the operating officials. Here the production engineer with the technical approach, time studies, control methods, past experience, and available records can help in detecting causes of inefficient phases of the operations. With these studies, a careful analysis can be made in setting up the expected standards to be followed. Management can then compare the job under study with the standards and make corrections to solve the problems. 5.2-1. Annual or Daily Coal Production. Once the production cycle has been established, it is paramount that coal sales keep the productivity of the mine as high as possible. A successful company does this by what they call "the control approach." The daily tonnage report is one of the things that is a potent control tool in attaining the goals to be achieved. If production is falling short of the goal, the daily tonnage report will reveal what has to be done in the remaining days of the month or year to achieve the expected schedule. When goals are reached or exceeded, then budgeted tonnages and costs will be reached or exceeded and thus assure attainment of a profit. Failing to keep to the scheduled pace shows up quickly and prominently, facilitating any necessary action to get things back to the projected plans. The sales target is usually set a little higher than the operating production. The sales tonnage is scheduled and sales are made accordingly, slightly

Jan 1, 1968

By David Phillips, George Jura

WHEN Bridgman1 determined the volume-pressure relationships of bismuth to 100 kg Cm-2, he found two small volume discontinuities at 45 and 64 kg em-2. Probably every investigator in high pressures has determined the electrical resistivity of bismuth in this pressure range. Until Zeitlin and Brayman2 reported discontinuities in the resistance of bismuth at these pressures, no one had found resistance discontinuities

Jan 1, 1968

By John R. Hutchins

1ms is a report of nickel (wire) oxidation studies designed to test the validity of Valensi's1 equation developed for the kinetics of a reaction controlled by diffusion in a continuously growing product layer on cylindrical surfaces. The equation is:

Jan 1, 1968

By Barry K. McMahon

The fundamental problem in rock mechanics is accounting for the discontinuous and anisotropic nature of the jointed rock mass. It is this problem that makes rock mechanics distinct from the mechanics of steel, glass, or concrete. Existing mathematical models explain much of the behavior of rock cores in the laboratory but, in civil engineering at least, the rocks that matter are the ones that are already broken. On the other hand, the basically descriptive methods now used in engineering geology do not lend themselves easily to mathematical analysis. A set of indices of geological properties related to the strength and deformation characteristics of jointed rock is needed. Like the index properties used in soil mechanics these will probably not have precise mathematical meaning, but once correlations are established with large scale tests they can form a basis for the transfer of test results, obtained in one area under one set of conditions, to the prediction of rock behavior in another area under another set of conditions. Indices of rock properties are even more important in rock mechanics than in soil mechanics as the cost of testing is much higher. To be useful, these indices must be easily and quickly measured and give reproducible results when measurements are made by different people. In this paper the word "joint" means all naturally occurring rock fractures with less than 3 in. of clay or other soft coating material. EXISTING INDICES OF ROCK PROPERTIES A comprehensive review of indices of rock properties for intact rock is given by Deere and Miller.' They provide charts ". . . for estimating the strength or modulus properties for intact rock from the numerical indices obtained by either the Schmidt hammer, the Shore Scleroscope,

Jan 1, 1968

By Maurice Magee

The Ducktown ore deposits have been known, explored, and mined for 120 years. Eight massive sulfide ore bodies occur in highly folded and metamorphosed graywacke, graywacke conglomerate, mica schist, chloritegarnet schist, and staurolite schist of Precambrian age. The ore deposits are tabular bodies that have been extensively folded, generally conform to the enclosing rocks, but show local complex differences. The ore deposits, ranging in size from 250,000 tons to over 20 million tons, are composed principally of the minerals pyrrhotite, pyrite, chalcopyrite, sphalerite, and magnetite. Gangue minerals are quartz, calcite, actinolite, tremolite, hornblende, garnet, and masses of schistose wall- rock. Three fault systems are present that have influenced ore control and ore body configuration. Hydrothermal effects are evident in wall-rock alteration. Evidence of retrograde metamorphism is extensive in the wall and ore associated rock. Preliminary isotopic age dates have indicated four possible metamorphic events during the Paleozoic Era. Ore genesis is considered to be hydrothermal replacement of receptive beds, predominantly highly calcareous zones, quartzitic zones, and brecciated shear zones. Ore deposition is thought to have occurred during the Devonian Period, with later mobilization and recrystallization of the ore and gangue during Middle and Late Paleozoic times.

Jan 1, 1968

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute's H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company's Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968