Search Documents

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

Further evidence is presented as to the widespread occurrence of Thiobacillus ferrooxidans in nature in association with sulphide minerals. Leaching rates are discussed in terms of the effect of environmental parameters, particularly Eh and pH, on the bacterial process.The methods used to investigate leaching phenomena are described and the advantages and limitations of each method are discussed. A theoretical treatment of the bacterial leaching process is given which indicates that the optimum conditions arrived at by traditional methods are compatible with those deduced from consideration of the mathematics of continuous culture and thermodynamics

Jan 1, 1968

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By S. H. Penn

Preliminary experimental evidence seems to preclude the use of unlubricated mechanical force drills on the moon. Measured values of the coefficients of friction and adhesion between metallic and nonmetal-lic solids have been shown to increase in an ultra-high vacuum environment. The paucity of real knowledge of the influence of a hard lunar vacuum upon interacting solid surfaces, relegates current proposals to sample the moon with a mechanical force drill, to the equivalent of wildcatting on earth. Within a few years, drilling will be attempted on the lunar surface with tools that have been designed with parameters that are normally considered for most conventional terrestrial drills. Lunar drills must be light in weight, portable, have reasonable penetration rates, low manpower requirements, etc. Although the initial equipment cost is expected to be high, this will probably not be a critical factor. Early lunar drilling will be limited to shallow holes with depths of 10 ft or less. The primary function of these holes will be to furnish samples of lunar surface materials but they may also be utilized for other purposes, such as geophysical experiments. Instruments may be installed in them capable of measuring thermal diffusivity, gamma radiation, etc. As sampling will be the primary objective of the earliest holes, sample contamination is a parameter that effectively excludes such otherwise promising techniques as explosive or plasma jet drilling. The most desirable method is probably some form of mechanical force drilling that has the capability of operating in the extreme lunar thermal environment (125° to 37S°K), high vacuum (10- l3 torr range), and low gravity.

Jan 1, 1968

By John H. Schilling

The Gabbs magnesite-brucite deposit is unique in size and is one of two magnesite deposits being exploited in the United States. It is near the town of Gabbs, which is one hundred miles southeast of Reno, in west-central Nevada. The brucite was discovered in 1927; the magnesite was found while exploring the brucite. During World War II, more than 80,000 tons of magnesium metal was produced from about 900,000 tons of magnesite ore mined from these deposits. An additional 5,000,000 tons of magnesite and 1,000,000 tons of brucite have been produced for use in making magnesia refractories and chemicals. Basic Inc., presently the only producer, mines 1.5 ± 0.25 million tons of ore and waste annually using high-selective open-pit rriethods; the ore is up-graded, calcined, and processed into a variety of products. Known reserves of highgrade (less than 5 per cent CaO) magnesite ore total more than 25,000,000 tons, and there are larger tonnages of lower-grade material; brucite reserves are small. The magnesite and brucite are in generally west-dipping dolomite of the upper member of the late Triassic Luning Formation, in the over-riding plate of the Paradise thrust fault. A great variety of dikes and a stock of Cretaceous granodiorite intrude the Luning Formation in the vicinity of the magnesite-brucite deposit. The magnesite bodies are scattered over an area of about a square mile around a prong of granodiorite which extends north from the stock. The brucite is mainly in two bodies in contact with the prong of granodiorite; at the surface and along deeper cracks the brucite has weathered to hydromagnesite and artinite. In the area of magnesite-brucite mineralization, much of the dark, fine-grained, schistose, regionally-metamorphosed dolomite of the Luning Formation has been marmorized to a lighter-colored, coarser-grained, massive dolomite that is intergrown in varying proportions with the magnesite. The magnesite and marmorized dolomite can not be distinguished visually. In addition to the two varieties of dolomite, the gangue in the magnesite and brucite bodies mainly is the various varieties of dike rock, serpentine and a variety of other "contact" minerals, and "post-ore" dolomite and calcite. The magnesite ( and recrystallized dolomite) is believed to have formed by the hydrothermal replacement of the regionally metamorphosed sedimentary dolomite; alternatively it has been suggested that the magnesite is sedimentarv and formed contemporaneously with the dolomite in an embayment of the Triassic sea. Because all the igneous rocks exposed in the immediate vicinity of the magnesite deposits appear to be younger than the magnesite, the ore-forming solutions are thought to be related to a somewhat older granite which crops out elsewhere in the area. The brucite is the result of contact-metasomatic replacement of magnesite during the emplacement of the granodiorite stock.

Jan 1, 1968

By D. R. George, J. R. Ross, J. D. Prater

In the United States nearly 200,000 tons of copper per year are being produced, by leaching waste rock and oxidized copper ore with dilute sulfuric acid-ferric sulfate solutions and precipitating the copper on scrap iron. The flow of solutions is in excess of 80 million gpd. A survey conducted by the U.S. Bureau of Mines in late 1965 at 14 mines in Arizona, Utah and Nevada, showed that with a few exceptions, the solutions contain from two to a maximum of 15 ppm U3O8, and there is strong evidence that these represent equilibrium concentration and not merely an accumulated in-process inventory resulting from recycling the solutions for many years. Consequently, it is believed that uranium could be recovered at a constant rate as long as mining and leaching operations continue. Preliminary surveys and estimates by the USBM indicate a production potential of possibly 1000 tons of U3O8 per year at a cost of less than $8 per lb if the major process streams from most of the large copper mines in the western United States were to be treated. Laboratory research by the USBM showed that the uranium could be efficiently recovered as a specification-grade uranium concentrate by a combination of ion exchange resin and solvent extraction of liquid ion exchange techniques. A joint pilot plant investigation by Kennecott Copper Corp. and the USBM was conducted on solutions from the Bingham Canyon mine to evaluate a new system of countercurrent ion exchange developed during the laboratory studies. In subsequent small-scale continuous tests, recovery of uranium from the pregnant eluate by solvent extraction and chemical precipitation techniques was investigated.

Jan 1, 1968

By Harold M. Feder, Robert V. Schablaske, Irving Johnson, Ewald Veleckis

The stoichiometry, structure, and stability of the internzediate phases formed between zinc and some of the rare earth (RE) metals were systematically exarnined by means of a recording effusion balance and X-ray diffraction analyses. In the La-, Ce-, PY-, Nd-, and Y-Zu systems, at or below about 600 C, the following sequences of phases (REZnx) were found: La, x = 1, 2, 4.0, 5.25, 7.3, 17/2, 11, and 13.0;' Ce, x = 1, 2, 3, 11/3, 4.3, 5.25, 7.0, 17/2,* and 11; Pr,x = 1,2, 3, 11/3 ,* 4.3, 5.3(?), 7.0, 17/2,* and 11; Nd,x = 1,2, 3,* 11/3,* 4.3, 6.5, 8.5,* and 11; Y,x = 1,2,3, 11/3, 4.5, 5.0, 17/2,* and 12.* The structure types of all these phases were classified. In addition, lattice parameters were obtained for the first time for the pluses denoted by asterisks. In the absence of de tectable valency or electronegativity effects the systesnatic trends in the results have been ascribed to the effects of' the lanthanide contraction. For example, the maximum number of zinc atoms in the coordination polyhedron surrounding the RE atom decreases from twenty-four to twenty-two to twenty as the size of the RE atom decreases. THE structures and compositions of a great many intermetallic phases (e.g., the Laves phases) are known to be based primarily, but not exclusively, on the space-filling efficiency of various modes of packing together atoms of different sizes. The valencies and electronegativities of the constituent atoms are, however, also influential. In extreme cases hypothetical intermetallic phases which fulfill the efficient spacefilling requirements may not be present in the constitutional diagram because of thermodynamic instability brought about by the operation of valency or electronegativity factors. Hence, for a detailed study of the influence of atomic size on alloy structure and composition, it would be desirable to minimize variations of valency and electronegativity. The intermetallic phases formed by the rave earths (RE) with some common partner offer an excellent opportunity for isolating the effects of size from those of valency and electronegativity. The rare earths exhibit a large, but smooth, decrease in size (the lanthanide contraction) in the series from lanthanum to lutetium when inter comparison is made for a common valence state, e.g., isolated atoms or trivalent ions. The elements yttrium and scandium are frequently included as pseudo rare earths; their sizes place them in the vicinity of dysprosium and lutetium, respectively. The electronegativities of RE elements vary by less than 10 pet. The trivalent state is the most common; however, the well-known tendency of cerium, praseodymium, and terbium to achieve higher valencies, and of samarium, europium, and ytterbium to seek lower valencies, requires that caution be exercised in the assumption of equal valencies. In the present study the existence, constitution, and structure of each of the numerous intermediate phases formed by zinc with lanthanum, cerium, praseodymium, neodymium, or yttrium were examined systematically and in detail. The investigation was conducted by a recording effusion balance technique and by X-ray diffraction analysis. The results enrich our knowledge of the phase diagrams of these systems. In addition, they present some clear-cut evidences of the operation of the size factor alone. EXPERIMENTAL PROCEDURE Apparatus. The mode of operation of the recording effusion balance and its application to phase studies have been discussed in detail elsewhere.' In this work, an effusion cell containing a finely divided alloy was suspended within an evacuated tube from the beam of an analytical balance. The tube was immersed in a massive molten salt bath whose temperature was controlled to within 0.5o C during each experiment. The loss in weight of the alloy owing to effusion of zinc* was continuously recorded. Two effusion cells, 1/2 in. diam by 1 in. high, were machined from tantalum rods. Two orifices were drilled laterally into the walls of each cell. The orifice areas were determined by calibration with pure zinc: cell A had a total orifice area of 6.5 x 10-41 sq cm, and cell B an orifice area of 9.8 x 10-3 sq cm. By appropriate choices of orifice area and temperature the wide range of volatilities from pure zinc to pure rare earth metal could be investigated. X-ray diffraction powder photographs were made at room temperature with a 114.6-mm Debye-Scherrer camera with both filtered CuKa radiation and filtered CrKa radiation. Lattice parameters were refined by a computer-programmed least-squares analytical treatment which incorporated appropriate extrapolation techniques.2 Frequent use was also made of a special computer program3 designed to generate a powder pattern from an assumed structure in order to verify structural assignments. Materials. Lanthanum, neodymium, and yttrium were purchased from the Lunex Co., cerium from the Cerium Metals Corp., and praseodymium from the St.

Jan 1, 1968

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,' the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By W. S. Owen, T. Bell

The variation ox the M, temperature with nitrogen concentration has been determined experinzentally. The free-energy difference between martensite and the parent y Phase at the M, temperature,is computed for Fe-C and Fe-N alloys using recent solubility data fm the Fe-N system and new data for the variatim of the activity of the interstitial solute in the y phase with concentration. The "geometric model" is considered also, and the importance of Zener ordering is noted. It is shown that, although at any chosen concentration the M, temperature and the activity are significantly different in the two alloy systems, the free-energy duference is the same within the limits of experimental error, thus Providing further evidence of the very close similarity between the martensite transformations in Fe-C and Fe-N alloys. TO estimate the free-energy change accompanying the martensite transformation in binary interstitial alloys it is necessary to know the variation of the Ms temperature with interstitial solute concentration and some thermodynamic data. To date, only the Fe-C system has been discussed because this was the only system for which relevant experimental measurements had been made, but even in this case the data available are insufficient to permit the free-energy change to be calculated without the assumption of a thermodynamic model for the y and a solid solutions. The last comprehensive discussion of the topic was by Kaufman, Radcliffe, and Cohen in 1.960.' Since that time Ellis, Davidson, and Bodsworth2 have redeter mined the activity of carbon in y iron as a function of carbon content and Atkinson3 has measured the activity of nitrogen in Fe-N austenite. The M, temperature of Fe-N is reported in the present paper. Thus, it is now possible to assess the free-energy change accompanying the martensite transformation in Fe-N alloys on the same basis as that used to assess the change in Fe-C alloys. This comparison is of interest because it has been shown recently4 that the structure of the martensite formed in Fe-N alloys changes with nitrogen content in a manner exactly parallel to the changes in structure in the Fe-C series and that the strain associated with the distortion of the iron lattice in either the y or the a phase by a nitrogen atom is the same as that produced by a carbon atom. The work to be described tests whether or not this close similarity between the two systems extends to the thermodynamics of the martensitic transformations. THE Ms TEMPERATURES FOR Fe-N MARTENSITE Bose and Hawkes5 found the M, temperature of a eutectoid Fe-N alloy (2.35 wt pct N) to be 35°C. This single determination appears to be the only reported measurement of the M, temperature of an Fe-N alloy. In the present work a series of more than fifteen different specimens containing between 0 and 2.7 wt pct N were prepared by controlled nitriding of pure iron wire 0.010 in. diam. The iron was supplied by B.I.S.R.A. and was designated ACN2. The nitriding procedure, all aspects of which are critical, has been described in detail elsewhere.' Each specimen was quenched from the austenitizing temperature into brine at 20°C without removing the specimen from the ammonia-hydrogen atmosphere in which it was ni-trided. Alloys containing up to 0.7 wt pct N were fully martensitic. More concentrated alloys contained progressively more retained austenite. At 2.34 wt pct N the specimen was completely austenitic after quenching to 20°C. The M, temperature of specimens with M, temperature above 20°C (those containing less than 2.35 wt pct N) was determined by a thermal arrest technique. For the more concentrated alloys (2.35 to 2.70 wt pct N) the variation of electrical resistance with temperature down to -196°C was used. Unlike Fe-C alloys, Fe-N alloys cannot be reaus-tenitized in vacuum or in an inert atmosphere because excessive loss of nitrogen occurs, even in short times, at high temperatures. Consequently, the alloys were reaustenitized in the ammonia-hydrogen mixture corresponding to nitrogen equilibrium at the temperatures used. The specimens were quenched in a blast of cold hydrogen gas and the temperature, measured by a thermocouple welded to the 2.5-in.-long specimen, was recorded on a high-speed recorder. In the first experiments 0.002-in.-diam chromel-alumel wire thermocouples were used but it was found that these gave erroneous readings due to contamination by nitrogen pickup. Pt-Pt 13 pct Rh wires of 0.002 in. diam were found to be satisfactory. Further details of the experiments are available in the original thesis.7 The cooling rate was controlled between 400° and 4000°C per sec by adjusting the hydrogen pressure. At least three cooling curves were obtained for each composition. Each specimen was analyzed for nitrogen after quenching. To aid in the accurate location of the martensite arrest points a series of cooling curves of 0.010-in.-diam platinum wire were recorded and these, which did not contain an arrest, were used as comparison standards. Four specimens, each in the form of a 3-in. loop, were prepared from each of the four alloys containing more than 2.35 wt pct N. One specimen was used for nitrogen analysis, one for X-ray diffraction, and two for resistance measurements below 20°C. The latter specimens were quenched from 20°C into constant-temperature baths at selected lower temperatures.

Jan 1, 1968

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

By H. L. Snyder

This paper outlines the approach to the underground construction work involved in the Churchill Falls Power Project. It is the first in a series of papers which CIM Bulletin plans to publish as the different 11hases of this large-scale operation evolve.

Jan 1, 1968

By John S. Brown

The northeastern United States embraces that area of the Appalachian Mountains, and adjacent territory, beginning on the south at the Potomac River. It thus extends from the flat-lying Paleozoic terrane of the Appalachian plateau on the west, across the folded Paleozoics of the Great Valley and adjacent ridges (Paleozoic and Precambrian), over the Piedmont and New England metamorphic complex (mixed Paleozoic and igenous rocks), broken by the great Triassic rift remnants, onto the subdued coastal plain of Cretaceous and Tertiary sediments. Although not noted as a metal mining region, the area does contain numerous substantial and several outstanding mines, chiefly of the more prosaic metals, particularly iron, zinc, and copper, as well as many minor occurrences of these and a few additional items. These deposits occur to some extent in every subdivision of the area. The region to date (1966) has produced almost 500,000,000 tons of medium to lowgrade iron ore, especially magnetite, including ilmenitic magnetite; 50,000,000 tons of highgrade zinc ore; and 5,000,000 tons of lowgrade copper. In the past, it has yielded small amounts of chromite and nickel, and at present is a large producer of titanium. Precious metals are conspicuously absent, and so also are the Tertiary or Mesozoic igneous phenomena so commonly associated with mines of the West. Hence, a survey of the extensive mineralization · of this region should be instructive

Jan 1, 1968

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Henry Rumfelt

8.1-1. History and Description of Shovels. The history of excavating machinery is not clearly defined but the machines seem to have been originally developed for dredging activities, principally involving rivers and harbors. The first, as far as can be determined, was a steam "spoon dredge" developed by Grimshaw of Boulton and Watt of Sunderland, England, in 1796. The land machine forerunner of the present-day power shovel was not developed until 1835. It was invented by William Smith Otis, a young partner of a Philadelphia contracting firm by the name of Carmichael and Fairbanks. The moving force behind this invention was the heavy activity in railroad construction. From this early start the power shovel has developed from steam powering to internal-combution-engine powering and to electric powering. In both directions it has developed to its present state of a finely engineered and precision-built tool. Through the interim the railroad-type shovel, about a half-swing arrangement designed especially for making railroad cuts and mounted on rails, was developed. The rail-mounted shovel gradually gave way to the full revolving shovel. It was high on the list in 1912 and was practically extinct by 1927. From the beginning, a few of the small revolving shovels designed primarily for the general contractors' market had found their way into quarry and mining operations. During this same period, the stripping shovel had been introduced-a 2 ½ cu. yd., 100-ton, full revolving stripping machine with a 41 ft boom. Although this shovel was designed especially for stripping, it was also used for heavy-duty, open pit mining service. In 1925 the heavy-duty, full revolving quarry and mine machine was developed. Strip mining shovels evolved through a somewhat separate path. Hand digging plows and mule-drawn slip scrapers were first reported used by Kirkland, Blakeney and Groves near Danville, Illinois for strip mining

Jan 1, 1968

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By K. E. Gray

The status of rock mechanics as applied to petroleum production might be termed, "Rock Mechanics-A New Name for Old Problems." The petroleum industry's efforts, from its earliest days, have been concerned with rocks, hopefully containing hydrocarbon accumulations in economic quantities. Geophysical and geological studies, wildcat and development drilling procedures, well bore mechanics and reservoir engineering operations, and certain aspects of production operations involve rock mechanics in various ways. Stress states and temperatures of interest range from low values in surface or near-surface activities, to very high values encountered at depths now exceeding 25,000 ft; deeper and deeper drilling will continue to increase this range. Time scales vary from a few microseconds in wave propagation measurements and some aspects of rock behavior during drilling, to seconds, minutes or hours for other drilling and well bore mechanics problems, to several years during which the efficient and economical depletion of reservoir systems is achieved. Subsurface sedimentary formations contain various fluids, of course, and reservoir fluid movement commonly involves three-dimensional, three-phase (oil, gas, and water) fluid flow. Many extremely difficult problems in rock mechanics arise for the Petroleum Engineer because of fluid movement (or lack of desired movement) in a well bore or reservoir. The discussion to follow illustrates just a few of the many topics in rock mechanics of significance to the petroleum industry. Time precludes anything other than a superficial treatment of the topics mentioned. A great deal of work has been carried out by various research groups in the petroleum field and significant efforts are continuing, as a review of the technical literature will reveal.

Jan 1, 1968

The occurrence of molybdenite in a small shaft in the western margin of the Wuuluman Granite in central western New South Wales is noted. Full petrographic and mineragraphic descriptions are given of a mineralized contact zone between the granite and a basic hornfels.Mineralogical data .indicate a similarity between this mineral occurrence and other occurrences in larger mines remote from the granite.

Jan 1, 1968