Search Documents

By F. W. Jessen, R. W. Durie

The development in the laboratory of mall salt cavities illustrated that the rate at which salt dissolved was affected by the rate at which fresh water was injected into the cavity. Experiments carried out with small salt cores indicated, however, that the rate of salt removal with forced convection was not significantly different from that with natural convection, provided the flow was in the laminar range. The rate of salt removal was apparently controlled by the water salinity, which was indirectly determined by the rate at which fresh water was injected. With turbulent flow at the salt surface, the rate of salt removal could be increased several-fold with the same salinity in the cavity. A quantitative evaluation of the rate of salt removal under natural convection was attempted by using techniques developed for the analogous heat convection system. The values of the rate of salt removal obtained experimentally were considerably greater than the calculated values due to surface irregularities. To determine the effect of these irregularities, the rate of salt removal was found for a smooth surface by experimentally determining the rate of salt removal as an irregular surface developed and then extrapolating this trend back to initial time. Excellent agreement between the experimental and calculated values then were obtained. INTRODUCTION Underground cavities leached from massive salt formations have been used extensively for many years for storing LPG products. The development techniques for storing methane gases in the liquid state at a low temperature leads to speculation that underground salt cavities of controlled geometry may be quite important in this field. In any case, the increasing number of salt cavities used for storage indicates an impending need for a better knowledge of the washing process to efficiently develop maximum storage volumes within specified regions. It is the purpose of this paper to discuss some aspects of -the mechanism of the dissolution of salt in the formation of cavities of controlled geometry. Although no attempt is made to resolve the problems that may be associated with the storage of methane in the liquid state in salt formations, the fact that salt cavities can be formed at reasonable cost would appear to justify investigation in this direction. Further, underground cavities have the advantage of allowing storage at higher pressures (and hence higher temperatures) than surface installations. Although the thermal conductivity of salt is somewhat higher than frozen earths, 0.017 cal/(sec) (cm)(c) for salt at 32F vs 0.005 cal/(sec) (cm) () for ice at this temperature, this disadvantage is offset by the higher storage temperature in underground cavities. For example, at atmospheric pressure, the temperature of liquid methane would be —258F. In a storage cavity at 2,000 ft, the pressure would be approximately 1,000 psia, which would allow a storage temperature of -9OF. The formation temperature would be roughly 110F at this depth, hence the total temperature differential would be 200F. Under surface storage conditions the corresponding temperature difference would be some 333 F (75 F + 258 F). The results of this difference can be compared more readily by substituting the appropriate values of thermal conductivity, temperature difference, heat capacity and density into the solution of the diffusion equation for the unsteady linear conduction of heat. For the underground salt storage, the heat flux is 15cal/(sec) (sq cm), where t is the time in seconds from the initiation of the cooling. For the surface system, and using the thermal properties of ice at the average temperature, the corresponding figure is 21cal/(sec) (sq cm). Hence, the heat losses through ice under surface conditions would be some 30 per cent higher than the underground salt storage. This ratio would vary, considerablv. Of course, for other conditions, but it indicates that an advantage over surface facilities may be obtained by storage in underground salt cavities.

Jan 1, 1965

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

By J. M. Neilson

The occurrence of iron ore deposits in the State of Western Australia has been known at least since the 1930's,3 but the true significance of the deposits has only come to light within the past four years. Although they are widely distributed throughout the State, it is now known that more than 90% of the available iron ore reserves are located in the "Hamersley Iron Province". Western Australia may well contain the world's largest known reserves of iron ore. Recent reports place this reserve at 15 billion tons and an even higher figure may appear in the future. LOCATION, CULTURE AND COMMUNICATIONS It is difficult to comprehend the immense size of Western Australia (Fig. 1). The State occupies almost one million sq miles and it is more than 2000 miles from north to south. More specifically, it stretches from the 14th to the 35th parallel of latitude south. The Ophthalmia Region in the Hamersley Iron Province is barely halfway up the long dimension of the State. Nevertheless, the region is 800 miles north of Perth, a distance comparable to that from New York to Chicago or to that from Chicago to New Orleans. The Hamersley Iron Province (so named in 1963 to distinguish it from the Pilbara mineral district adjacent to it on the north) covers an area of approximately 30,000 sq miles in the northwestern part of the State. It extends in a roughly oval form from the Indian Ocean to the Gibson Desert of the interior, a distance of about 300 miles. With the exception of the small coastal towns of Onslow, Roebourne and Port Hedland and a few other communities such as the asbestos-mining town of Wittenoom, the region is very sparsely populated. Sheep and cattle stations are scattered thfough the region and these and the main towns are connected by truck tracks and a few main highways. Voice communication is almost entirely by the short-wave radio net operated by the Royal Flying Doctor

Jan 1, 1965

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By John Nagy

Dust explosion data obtained in laboratory studies by the Bureau of Mines are presented for activated carbon, asphalt, charcoal, carbon black, coal, coke, gilsonite, graphite, lignite, miscellaneous carbons, pitch, tunnel dust, and mixtures of these materials with other ingredients. The explosion hazard is shown to increase as the volatile content of the dusts increases.

Jan 1, 1965

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

By H. Conrad, K. Janowski, G. Stone

The available data on the dynamics of plastic flow of sapphire indicate that the deformation rate in the temperature range .from 900° to 1700°C can be expressed either as A number of investigators1-10 have established that sapphire deforms plastically above 900°C, the most common mode of deformation being slip on the basal plane in the [1120] direction. Under certain conditions and at temperatures above 1500°C, slip

Jan 1, 1965

By A Hitchen

A general outline is given for the determination of copper, nickel, cobalt, zinc, lead, cadmium, bismuth, manganese, uranium, molybdenum, vanadium, sulphate and fluoride by polarographic or amperometric methods in a variety of ores or metallurgical products. The detection of oxygen in gas mixtures by an amperometric method used as a safety device is also discussed. Introduction I N this paper, a general outline will be given of the polarographic and amperometric methods used for the chemical analysis of various ores and metallurgical products in the Chemical Analysis Section of the Extraction Metallurgy Division of the Mines Branch. The methods to be discussed will be confined to those based on the use of normal D.C. polarography and will not include those methods which utilize a cathode-ray, square wave, pulse or A.C. type of polarograph. For the sake of convenience, ? the polarographic methods will be discussed according to the type of supporting electrolyte employed, as the same electrolyte may serve to determine more than one element in more than one type of ore. Amperometric methods will be discussed according to the element to be determined rather than

Jan 1, 1965

By M. S. Burton, H. H. Kranzlein, G. V. Smith

The influence of up to 2 at. pct of Ni and Pt on the yield strength of mono- and polycrystalline high-purity iron has been evaluated at temperatures from + 25° to -196°C. Current theories of solid -solution strengthening fail to explain the experimental observations. The temperature dependence of yield stress was found to be less in the alloys than that in high-purity iron. The room-temperature yield stress increased with alloy content, but at —78°C the yield strength first decreased with increasing a1loy content. AS a result of many studies, a number of theories have been proposed for solid-solution strengthening. The purpose of the present study was to evaluate these theories, as applied to the solid-solution strengthening observed in Fe-Ni and Fe-Pt alloys. Of various theories of solid-solution strengthening, those of Cottrell,1,2 Fisher,3 Suzuki,4 and Mott and Nabarro5 are most prominent, and have been discussed widely in the literature.'-' Of the recent concepts of solid-solution hardening the work of Fleischer9 is notable. Each of these models has been applied to particular alloy systems with some success, but in general none has proved generally applicable. In many of the previous studies to assess the effects of alloy additions in ferrous systems, lack of adequate control of the purity and grain size of the materials has obscured strengthening effects, so that few comprehensive data relating composition, temperature, and change of lattice parameter have been determined. In the present investigation an attempt was made to obtain data which would be meaningful in evaluating the theories of strengthening. Materials of high purity were used to minimize extraneous impurity effects, and both single crystals and polycrystalline materials were studied to evaluate the effect of grain boundaries. Nickel and platinum were chosen as alloy additions, because both belong to the same chemical group and have the same crystal structure and valence, with markedly different atomic diameters. It appeared that some conclusions regarding atomic size effect on strengthening might be made. MATERIALS AND PROCEDURES Fe-Ni and Fe-Pt alloys containing 0.5, 1.0, 1.5, and 2.0 at. pct alloy additions were prepared from high-purity materials. The iron was supplied by the American Iron and Steel Institute from a stock of 99.98 pct zone-refined iron prepared by Battelle Memorial Institute. The minimum purity of the nickel and platinum used for alloying was 99.98 and 99.999 pct, respectively. Alloys were prepared by levitation melting, cast into cylindrical copper molds, and cooled, all under a partial pressure (0.3 atm) of purified helium. Samples were 0.375 in. in diameter and weighed 20 to 25 g. Chemical analyses of the alloys are given in Table I. A sample of unalloyed iron also was cast as a control specimen.

Jan 1, 1965

By William R. Patterson

ACCORDING to the phase diagram for the Mn-Ni system,' the high-temperature, fcc y-manganese solid solution is stabilized to below room temperature, in the range approximately 22 to 28 wt pct Ni. However, pearson2 cites evidence in the literature showing that for manganese contents greater than about 75 wt pct the quenched phase in Mn-Ni alloys is fct. This is in keeping with zener's3 suggestion that in manganese-rich alloys the fcc high-temperature phase undergoes a diffusionless or martensitic transformation to a fct structure upon quenching. Work by Basinski and christian4 on manganese-rich compositions in the similar alloy system Mn-Cu established that in alloys of greater than about 82 wt pct Mn the y-manganese phase underwent a fee fct martensitic transformation upon quenching to room temperature. Striking evidence for this martensitic transformation was the highly twinned or banded microstructure, an example of which is shown in Fig. 1. Similar microstructures have also been found in quenched Mn-Cr5 and Mn-Au6 alloys. In the present investigation, we attempted to obtain similar evidence of a fcc — fct martensitic transformation in manganese-rich Mn-Ni alloys. Manganese alloys in the range 10 to 30 wt pct Ni were prepared by arc-melting, under argon, at atmospheric pressure. The alloys all were 50 g in size, and negligible weight loss occurred during melting. The starting materials were electrolytic manganese and nickel, both of 99.9+ pct purity. The alloys were subsequently homogenized 48 hr at 1750°F, hot-rolled 50 pct at 1700°F, annealed 2 hr at 1700°F, and water-quenched to room temperature. All heat treatment was done in purified argon. Both X-ray and metallographic techniques were used to examine the structures of the quenched alloys. X-ray diffractometer studies were conducted on powder specimens obtained from filings rean-nealed 2 hr at 1700°F in argon and water-quenched. Identification of the intensity peaks from the diffractometer counter traces showed that below about 10 to 12 pct Ni the y phase decomposed partially upon quenching to give an a- + ?-manganese structure. In the range approximately 12 to 25 pct Ni, the structure was found to be fct ? manganese with a c/a ratio approaching 1.0 at 25 pct Ni. Beyond approximately 25 pct Ni, the structure remained fcc. These results, including lattice-parameter determinations, are given in Table I. Metallographic examination. was carried out on specimens polished and etched after quenching, and also on polished specimens reannealed and quenched. In the first case, the distinctive twinning or banding so prevalent in Mn-Cu alloys was sought, while in the second, the surface relief effect generally regarded as being truly characteristic of a martensitic transformation was sought. The microstructure of representative alloys in the range 12 to 25 pct Ni is shown in Fig. 2. The structure of the Mn-15 pct Ni

Jan 1, 1965

By Bagley A. S

The accuracy and precision of rutile analyses are discussed. Comparison is made between the wet chemical and X-ray fluorescence spectrographic methods of. estimating Ti02 in commercial rutile. Various allotropes of 'I'i02 are identified by diffractometry and a comparative analysis of the coloured varieties of rutile is given. For X-ray fiuorescence . analysis, specimen preparation is critical and sample grinding and pressures. for pellet making are discussed in detail.Cellulose bonded and backed pellets are shown to be subject to relaxation with increasing age.INTRODUCTIONTo date much of the analytical work on commercial samples has been done by wet chemical methods.This led to various discrepancies in results, which are of particular importance when certificates must be issued for overseas shipments. The present work reviews the nature of rutile and compares the results of Ti02 estimation by wet chemical methods and those obtained by X-ray fluorescence spectrographic analysis.In the rutile industry the results from different analysts and even those from the same analyst are not always consistent. To the analytical chemist this should not be surprising.Fairbairn (1951) showed the results obtained from 34 different analysts on a specially prepared sample of granitic rock. It is of some interest to note that the Ti02 content as determined by the 34 analysts using unspecified methods ranged from 0-17 per cent to 0·30 per cent. Fairbairn (1953) found that1. replicate analyses from the same analyst give a high order of precision,2. analyses by different analysts using the same procedures give reasonable precision, and...

Jan 1, 1965

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

By S. E. Khalafalla

The Bureau of Mines investigated variations in the activation energy for the carbon monoxide reduction of magnetite and ferrous oxide with respect to the state of aggregation of the oxide material. Reduction phenomena can only be satisfactorily explained by including an adsorption step in the reduction process. Summation of the values of the exothermic heat of chemisorption and the variable apparent activation energy for reduction yields a nearly constant value of about 50 kcal for either ferrous oxide or magnetite regardless of whether they are aggregated in pelletized form or coarsely crystalline particles.

Jan 1, 1965

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß' and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.' Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965